mac80211 does it for us.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "ath9k: Change rate control to use legacy rate as last MRR"
resulted in the mixing of HT/legacy rates in a single rateset,
which is undesirable. Revert this behavior.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Trim API and remove unused variables.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A reference to the rate table is stored inside the
private structure, so there is no need to pass "rate_table"
around.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove various local variables that duplicate information
already stored in mac80211.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're holding the sta_list_spinlock here so we can't sleep.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Call cfg80211_michael_mic_failure() handler when there is a MIC error
event from firmware.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The key length can be 32 bytes for TKIP and 16 bytes for AES_CMAC.
'smatch' warns on memcpy using key_len variable to copy data to
a 16 bytes buffer. Use fixed length to avoid the warning.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can not assume parallel flash is always present, there are boards
with *serial* flash and probably some without flash at all.
Define some bits by the way.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Reviewed-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These warnings can be detected by using powerpc64-linux toolchain
(gcc-4.6.3-nolibc).

  CC [M]  drivers/net/wireless/mwifiex/sta_event.o
drivers/net/wireless/mwifiex/sta_event.c: In function 'mwifiex_process_sta_event':
drivers/net/wireless/mwifiex/sta_event.c:388:4: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  CC [M]  drivers/net/wireless/mwifiex/uap_event.o
drivers/net/wireless/mwifiex/uap_event.c: In function 'mwifiex_process_uap_event':
drivers/net/wireless/mwifiex/uap_event.c:258:11: warning: comparison of distinct pointer types lacks a cast [enabled by default]

Use min_t() instead of min() to fix the warnings.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no need to export the il_pci_suspend
and il_pci_resume functions since they're only
referenced from il_pm_ops. The latter can also
be defined using SIMPLE_DEV_PM_OPS instead of
open-coding it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Put power_level to ah_txpower struct with the rest tx power infos and
also rename it to txp_requested to make more sense.

v2 make sure we don't memset it to zero on reset
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By using cur_pwr on phy_init we re-use the power level previously set by the
driver, not the one we got from above.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rates[i] is unsigned but txp_offset can be negative for newer parts
with PDADC table. We cover the case when rates[i] + txp_offset > 63
but we must also cover the case when its < 0 or else rates[i] will overflow.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure we don't store the table offsets for min and cur power levels,
store the 0.25dB values instead. This way we don't clamp the tx power level
to max (because now cur_pwr holds the 0.25dB value, not the table offset) after
re-using cur_pwr on reset.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions and structs are not used in an other file and the
prototypes are in no header file, just make them static so the compiler
is able to optimize them better.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For the upcoming tpc changes, the driver needs
to provide sensible max output values for each
supported channel.

And while the eeprom always had a output_limit
table, which defines the upper limit for each
frequency and modulation, it was never really
useful for anything... until now.

Note: For anyone wondering about what your card
is calibrated for: check "iw list".
	* 2412 MHz [1] (18.0 dBm)
	* 2437 MHz [6] (19.0 dBm)
	[...]
	* 5180 MHz [36] (18.0 dBm)
	* 5260 MHz [52] (17.0 dBm) (radar detection)
	* 5680 MHz [136] (19.0 dBm) (radar detection)
(for a Dell Wireless 1450 USB Adapter)
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sequence counter will be sent to firmware via key_material
command.
Signed-off-by: NYing Luo <luoy@marvell.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'cipher' and 'seq' coming from cfg80211 add_key handler will be
parsed in mwifiex_set_encode() to handle AES_CMAC cipher suite.
Signed-off-by: NYing Luo <luoy@marvell.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This array was used for wapi_rxpn only. Now it will be used for
AES_CMAC as well. So make a generic name for it.
Signed-off-by: NYing Luo <luoy@marvell.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup TX/RX BA tables when AP receives deauthentication from
associated station. During BSS_IDLE event, all wmm queues, BA
streams created for AP interface are deleted.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for handling BA request and BA setup
events for AP interface.

RA list is marked as either 11n enabled or disabled from station's
capabilities in association request. BA setup is initiated only
after some specific number of packets for particular RA list are
transmitted.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for reception and decoding of AMSDU
aggregation frames for AP interface.
Patch also adds support for handling AMSDU aggregation event.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1. Separate file for uAP RX handling.
2. If received packet is broadcast/multicast, send it to kernel
   as well as requeue it back to uAP TX queue.
3. If received packet is for associated STA (intra-BSS), requeue
   it back to uAP TX queue.
4. In all other cases (packets for AP or inter-BSS packets),
   pass packet to kernel to handle it accordingly.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After station is associated an entry would be added to station
list. This entry would have station specific information such as
11n support, AMSDU size. The entry would be deleted after
deauthentication. All station entries would be deleted during
BSS_IDLE event.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Route AP events handling to separate function defined in
uap_event.c.
AP specific event handling is removed from sta_event.c.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If HT IE is present in beacon_data of start_ap cfg80211 handler,
enable 11n flag in AP. Disable 11n flag when stop_ap handler is
called.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Earlier scan command was postponed by 20msec multiple times to give
preference to Tx traffic until we find empty wmm queue.

There is a corner case in which wmm queue becomes empty immediately
after processing the packet(before 20msec) and there may be next
packet coming after some time. In this case we should not resume scan
operation.

We will use new flag to check Tx traffic and resume scan operation
only if there is no traffic for 200msec.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As per recent patch "658f37b7 mwifiex: scan less channels..."
less channels are scanned per scan command in associated state.

Default number of channels per scan command for normal scan are
already 4, but those are 14 for SSID specific scan operation.

This code change in this patch is required for SSID specific scan.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do similar conversion for Tx packet header but it was missing
for Rx packet header. Without this fix, Rx packet header won't
be correctly parsed on big endian platform.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Padding arithmetic will always work for MSDUs provided first MSDU
ends on 4-byte boundary. Fixing it by making sure that all MSDU ends
on 4-byte boundary.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>