This patch make it possible to mac80211 to know whether a frame
has been received with short preamble.

It simply checks for the "splcp" flag in the RX status
descriptor, and eventually set RX_FLAG_SHORTPRE in mac80211
rx status structure.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If allocation of io_dmabuf fails, rtl8187_probe() calls usb_put_dev(udev)
while usb_get_dev(udev) is not called yet. As a result refcnt is decremented
incorrectly and usb_dev can be used after memory deallocation.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANAPARAM3 register, defined in the rtl818x common register
struct, is accessed as 16bit by rtl8187se and as 8bit by rtl8187b.
Since I have no documentation about this, I can only stick to
the reference code and to what is known to work.

This issue has been addressed by a patch from Larry Finger
that introduces an "union", in the register struct.
In my last patch-set I applied it on the register struct, but
I forget to update rtl8187 driver too.
This patch does it.

Suggested-by: Larry Finger <Larry.Finger@lwfinger.net> [ Original patch ]
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In rtl8180/rtl8187 drivers, few register bit definitions have
names of form FOOBAR_SHIFT, suggesting they should be used as
shift offset, for example
reg |= (1 << ENABLE_FOO_SHIFT).

However they are actually defined as (1 << x) and thus they are
used (correctly) like
reg |= ENABLE_FOO_SHIFT;

This patch kills the misleading _SHIFT suffix.
Signed-off-by: Nandrea merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under heavy load, the relatively small number of RX queue entries are
completely filled. With an increase from 16 to 32 entries, this condition
rarely happens.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of __dev_alloc_skb() failure rtl8187_init_urbs()
calls usb_free_urb(entry) where 'entry' can points to urb
allocated at the previous iteration. That means refcnt will be
decremented incorrectly and the urb can be used after memory
deallocation.

The patch fixes the issue and implements error handling of init_urbs
in rtl8187_start().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A lot of files contain reference to my old e-mail address.
Now I'm going not to read mail from it anymore, so update it
with my current address everywhere.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.

Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Reported-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Herton Ronaldo Krzesinski <herton@canonical.com>
CC: Hin-Tak Leung <htl10@users.sourceforge.net>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Removes hw.conf.channel usage from the following functions:
 * ieee80211_mandatory_rates
 * ieee80211_sta_get_rates
 * ieee80211_frame_duration
 * ieee80211_rts_duration
 * ieee80211_ctstoself_duration

This is in preparation for multi-channel operation.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add AD-HOC support to the rtl8187 based on the rtl8180 source
Signed-off-by: NAttila Fazekas <turul64@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This converts the drivers in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.

Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Yoann DI-RUZZA <y.diruzza@lim.eu>
Cc: George <george0505@realtek.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The device.h header was including module.h, making it present for
most of these drivers.  But we want to clean that up.  Call out the
include of module.h in the modular network drivers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.

The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
	ops.conf_tx = conf_tx_op;

@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
	conf_tx_op (
-		struct ieee80211_hw *hw,
+		struct ieee80211_hw *hw, struct ieee80211_vif *vif,
		u16 queue,
		const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver for the RTL8187L chips returns IEEE80211_TX_STAT_ACK for all
packets, even if the maximum number of retries was exhausted. In addition
it fails to setup max_rates in the ieee80211_hw struct, This behavior
may be responsible for the problems noted in Bug 14168. As the bug is very
old, testers have not been found, and I do not have the case where the
indicated signal is less than -70 dBm.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).

Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.

Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These drivers share one header file, but nothing else.  Worse, both
drivers use the rtl8225 part with different register settings.  The
results has been some ugly naming -- let's simplify that.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>

Current 8187B initialization misses anaparam registers restore after
8187 reset. This causes ANAPARAM register to stay zeroed out (ANAPARAM2
kept its value on my tests). To avoid this, call rtl8187_set_anaparam
right after chip reset (to be on the safe side, as it makes sure we
restore all ANAPARAM registers).
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Usually you set RTL818X_CONFIG3_ANAPARAM_WRITE when you are going to
change/write ANAPARAM registers. But in current initialization of
RTL8187B there is a place where ANAPARAM_WRITE bit is set without any
ANAPARAM register being written, without reason, so remove it.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are repeated calls for anaparam on/off sequence in the code.
Consolidate the common code in rtl8187_set_anaparam and use it where
needed.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The GNTSel bit should only concern pci devices by looking at RTL8180
spec, which is not the case of 8187B. Also testing shows that trying to
set this bit fails, a subsequent read from the register after trying to
set it shows that the bit isn't set, seems the hardware ignores it,
which makes sense. This setting was a left over from Realtek sources.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On 8187B start, comment about pll reset, and move it out of ANAPARAM
write sequence, so that code is more readable.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The table with misc register initialization was setting it, and later
on we would set it again with a explicity call to rtl818x_iowrite16_idx.

Remove duplicate initialization from the register table.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were using wrong address for BRSR (Basic Rate Set Register) while
initializing its value, comparing with Realtek sources, for 8187B case.

Also, the same register is initialized in rtl8187b_reg_table, so remove
the duplicate initialization from the table.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On 8187B path, we set a initial value for beacon interval and atim
window on initialization. But this isn't needed, since same setup is
done on rtl8187_config.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes redundant write to Auto Rate Fallback Register on RTL8187B.
The same value was being written twice in the same function. Avoid this
removing the duplicate initialization on rtl8187b_reg_table, and also
add comment for this write (information from Realtek source).
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clearing the per packet TX AGC for the RTL8187B device appears to
increase its overall TX power. This allows the device to associate and a
connection to be established using APs a little further away.

This is in accordance to what is done for RTL8187L devices and also what
Realtek drivers do.
Tested-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: linux-wireless@vger.kernel.org
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Rogerio Luz Coelho <rogluz.news@gmail.com>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: seno <senada@t-online.de>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit c96c31e4
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case.  Restore the original case.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Standardize the logging macros used.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>