These are predefined states of the driver model. When not present,
as if not set in the device tree, they become no-ops.
Explicitly selecting the default state is not needed since the
device core layer sets pin mux to "default" state before probe.
This is not the simplest implementation, on AM335x at least, we could
switch to idle at any point in the suspend hook, only the default state
needs to be set before writing to the irq registers or an IRQ might get
lost.
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On multicores, an sdio irq handler could be running in parallel to
runtime suspend. In the worst case it could be waiting for the spinlock
held by the runtime suspend. When runtime suspend is complete and the
functional clock (fclk) turned off, the irq handler will continue and
cause a SIGBUS on the first register access.
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To detect sdio irqs properly without spurious events,
OMAP4 needs IWE in CON and CTPL, CLKEXTFREE in HCTL to be set
Tested-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add SDIO IRQ entries to debugfs entry. Note that PSTATE shows current
state of data lines, incl. SDIO IRQ pending
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.

Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.

This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.

This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.

Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>

For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.

To use it, you need to specify the wake-irq using the
interrupts-extended property.

[1] http://www.sakoman.com/cgi-bin/gitweb.cgi?p=linux.git;a=commitdiff_plain;h=010810d22f6f49ac03da4ba384969432e0320453
[2] http://comments.gmane.org/gmane.linux.kernel.mmc/20446Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

moving dmaengine consumer specific function to omap-dmaengine.h
to Resolve build failure seen with sh-allmodconfig:
    include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
    make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1

Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Check for set block count command fails always since host->cmd is set
to NULL in the same function incorrectly. Correct host->cmd usage properly.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

With devm_ioremap_resource conversion release_mem_region, iounmap can be
removed in clean up path
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

With devm_request_threaded_irq conversion free_irq can be removed
in clean up path
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

With devm_request_irq conversion free_irq can be removed in clean up path
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

With devm_clk_get conversion clk_put can be removed in clean up path
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Replaced UHS_DDR50 with MMC_DDR52.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Add support for autocmd23 support
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

Add set block count command support for close ended multiblock read/write.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

split start dma function into setup and start dma to keep track of
host_cookie when cmd23 support is enabled along with async request.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

mrq is not populated for set block count(cmd23) command.
Use block read/write mmc_commond pointer for request done and
avoid NULL pointer access in error case for sbc (cmd23).
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

clk_get_rate throws DEBUG_LOCKS_WARN_ON(in_interrupt()) warning
if called from interrupt context.
use cached clock rate in set_data_timeout, so that
set_data_timeout can be called from interrupt context.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

Remove redundant reset done check since omap hwmod layer ensures IP reset.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NChris Ball <chris@printf.net>

of_get_hsmmc_pdata returns a pointer, returning NULL is invalid,
return ERR_PTR for error case.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NChris Ball <chris@printf.net>

remove pbias workaround
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NChris Ball <chris@printf.net>

In DT case, PBAIS registers are programmed via regulator,
use regulator APIs to control PBIAS.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NChris Ball <chris@printf.net>

handle vcc and vcc_aux independently to reduce indent.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NChris Ball <chris@printf.net>

Use devm_regulator API, while at it use
devm_regulator_get_optional for optional vmmc_aux supply
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NChris Ball <chris@printf.net>

This should probably be done implicitly through mmc_of_parse(), but that
doesn't play well along with the multi-slot model the hsmmc driver
features. Hence, for now, do it manually. The properties are already
documented in Documentation/devicetree/bindings/mmc/mmc.txt.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

When device is booted using devicetree, platforms impacted by Erratum
2.1.1.128 is not detected easily in the mmc driver. This erratum
indicates that the module cannot do multi-block transfers. Platforms
such as LDP which use OMAP3 ES revision prior to ES3.0 are impacted by
this.

Provide a new compatible property "ti,omap3-pre-es3-hsmmc" to allow
driver to determine if driver needs to implement quirks associated
with the specific module version (primarily because the IP revision
information is not sufficient for the same).
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

Static checkers complain that testing for both "next" and "!next" is
duplicative.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <chris@printf.net>

Suspend and resume of cards are handled by the protocol layer and
consequently the mmc_suspend|resume_host APIs are marked as deprecated.

While moving away from using the deprecated APIs, there are nothing
left to be done for the suspend and resume callbacks, so remove them.

Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

With lazy disable gone, no_off is not used any more in omap_hsmmc
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

clock divisor can take a max value of 1023.  Update code so that card
init can be handled at f_min even at higher IP clock frequencies from
which clock to the card is derived.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

With HSMMC_HAS_UPDATED_RESET reset of cmd/data (SRC/SRD) can be to
quick and can be missed resulting in wait for software timeout.
With cpu_relax timeout can be long and unpredictable. Use udelay
instead for timeout implementation.
Reported-by: NYuzheng Ma <mayuzheng@kedacom.com>
Tested-by: NYuzheng Ma <mayuzheng@kedacom.com>
Reviewed-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NJianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We want to get rid of the omap specific platform init code
callbacks as they don't play nice with device tree.

Convert the context loss check to be based on a
register state detection instead.

Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
[add check for CON and HCTL in context save and restore function]
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

pbias_disable is set to protect the mmc pbias i/o cells in DT boot
by preventing voltage switch. Currently pbias_disable is enabled only
for omap3 and not for omap4 due to reg_offset difference of 0x100.
Enable pbias_disable for omap4+ too by using res->start
which does not include the reg_offset.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Commit 1f6b9fa4 consolidated writes to
the STAT register in one location, moving them from omap_hsmmc_do_irq()
to omap_hsmmc_irq(). This move has the unwanted side effect that the
controller status flags are potentially cleared after a new command has
been started as a consequence of reading the previous status flags.
This means that if the new command changes the status flags before the
IRQ routine returns, those flags may be cleared without handling the
event which asserted them, and thus missing the event.
Move the writing of the STAT register back in omap_hsmmc_do_irq(),
before handling the status flags which generated the interrupt.
Signed-off-by: NFrancesco Lavra <francescolavra.fl@gmail.com>
Reviewed-and-Tested-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

omap_hsmmc.c depends on <linux/sizes.h> being included indirectly by
another header. Once we enable COMPILE_TEST for this driver, we might
compile under architectures which won't include <linux/sizes.h> for us.
In fact, one such case is x86.

In order to prevent compile breakages, let's explicitly include
<linux/sizes.h>.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NSonic Zhang <sonic.zhang@analog.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC driver probe will abort for DT case because of failed
platform_get_resource_byname() lookup. Fix it by skipping resource
lookup byname for device tree build.

Issue is hidden because hwmod populates the IO resources which
helps to succeed platform_get_resource_byname() and probe.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Convert dmaengine channel requests to use
dma_request_slave_channel_compat(). This supports platforms booting
with or without DT populated.
Signed-off-by: NMatt Porter <mporter@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Otherwise SDIO cards won't necessarily work when booted with
device tree as we will never power down the SDIO cards. This
means the SDIO card reset does not happen which at least some
WLAN controllers expect to happen with ifconfig wlan0 down.

The PBIAS voltage is only available for the first controller
instance, so let's limit the PBIAS workaround to the first
controller only.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Tested-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the CD/WP-GPIOs are not provided by the SoC's GPIO controller,
we need to handle the case where omap_hsmmc is probed earlier than
the GPIO controller chosen in the device tree.

Fix this by checking the return value of of_get_named_gpio against
-EPROBE_DEFER and passing it through to the probe function.
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Define the most frequently used bitmasks of the Interrupt Enable /
Interrupt Status register with consistent naming ( with _EN suffix).

Use meaningful concatenation of bitfields for INT_EN_MASK, which shows
which interrupts are enabled by default.  No functional changes.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>