This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the tunnel APIs to use per tunnel
info instead of using bitmasks for all tunnels and also
uses single struct to hold the data to prepare multiple
variant of tunnel configuration ramrods to be sent to the hardware.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds necessary APIs to interface with
qede aRFS support in successive patch.

It also reserves separate PTT entry for aRFS,
[as being in fastpath flow] for hardware access instead of
trying to acquire it at run time from the ptt pool.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware can query for some basic iSCSI-related statistics.
Provide those just as we do for other protocols.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When qedr is enabled, qed would try dividing the msi-x vectors between
L2 and RoCE, starting with L2 and providing it with sufficient vectors
for its queues.

Problem is qed would also do that for storage partitions, and as those
don't need queues it would lead qed to award those partitions with 0
msi-x vectors, causing them to believe theye're using INTa and
preventing them from operating.

Fixes: 51ff1725 ("qed: Add support for RoCE hw init")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: NRam Amrani <Ram.Amrani@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware is used as an arbiter between the various PFs
in regard to loading - it causes the various PFs to load/unload
sequentially and informs each of its appropriate rule in the init.

But the existing flow is too weak to handle some scenarios where
PFs aren't properly cleaned prior to loading.
The significant scenarios falling under this criteria:
  a. Preboot drivers in some environment can't properly unload.
  b. Unexpected driver replacement [kdump, PDA].

Modern management firmware supports a more intricate loading flow,
where the driver has the ability to overcome previous limitations.
This moves qed into using this newer scheme.

Notice new scheme is backward compatible, so new drivers would
still be able to load properly on top of older management firmwares
and vice versa.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We'll soon need additional information, so start by changing
the infrastructure to receive the initializing variables
via a parameter struct.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware is used as arbiter between different PFs
which are loading/unloading, but in order to use the synchronization
it offers the contending configurations need to be applied either
between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE
management firmware commands.

Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and
qed_hw_reset() which don't abide this requirement; Most of the closure
is doing outside the scope of the unload request.

This patch removes qed_hw_reset() and places the relevant stop
functionality underneath the management firmware protection.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.

It also adds 2 new PCI device-IDs to qede:
  - 0x8070 for QL41xxx PFs
  - 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.

This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.

Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flows accessing registers require the flow to hold a PTT entry.
To protect 'major' load/unload flows a main_ptt is pre-allocated
to guarantee such flows wouldn't be blocked by PTT being
unavailable.

Status block initialization currently uses the main_ptt which
is incorrect, as this flow might run concurrently to others
[E.g., loading qedr while toggling qede]. That would have dire
effects as it means registers' access to device breaks and further
read/writes might access incorrect addresses.

Instead, when initializing status blocks acquire/release a PTT
as part of the flow.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the backbone required for the various HW initalizations
which are necessary for the FCoE driver (qedf) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: NArun Easi <arun.easi@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today qede requests contexts that would suffice for 64 'whole'
combined queues [192 meant for 64 rx, tx and xdp tx queues],
but registers netdev and limits the number of queues based on
information received by qed. In turn, qed doesn't take context
into account when informing qede how many queues it can support.

This would lead to a configuration problem in case user tries
configuring >64 combined queues to interface [or >96 in case
xdp isn't enabled]. Since we don't have a mangement firware
that actually provides so many interrupt lines to a single
device we're currently safe but that's about to change soon.

The new maximum is hence changed:
  - For RoCE devices, the limit would remain 64.
  - For non-RoCE devices, the limit might be higher [depending
    on the actual configuration of the device].
qed would start enforcing that limit in both scenarios.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous fix has broken RoCE support as the rdma_pf_params are now
being set into the parameters only after the params are alrady assigned
into the hw-function.

Fixes: 0189efb8 ("qed*: Fix Kconfig dependencies with INFINIBAND_QEDR")
Signed-off-by: NRam Amrani <Ram.Amrani@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware is interested in various tidbits about
the driver - including the driver state & several configuration
related fields [MTU, primtary MAC, etc.].
This adds the necessray logic to update MFW with such configurations,
some of which are passed directly via qed while for others APIs
are provide so that qede would be able to later configure if needed.

This also introduces a new default configuration for MTU which would
replace the default inherited by being an ethernet device.
Signed-off-by: NSudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the current default values for Rx path i.e., 8 queues of 8Kb entries
each with 4Kb size, interface will consume 256Mb for Rx. The default values
causing the driver probe to fail when the system memory is low. Based on
the perforamnce results, rx-ring count value of 1Kb gives the comparable
performance with Rx coalesce timeout of 12 seconds. Updating the default
values.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cleans many of the warnings that would arise in qed as a
result of compilations with C=1; Most of those are the addition
of missing 'static' to functions, although there are several other
fixes as well.
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The qedr driver would require a tristate Kconfig option [to allow
it to compile as a module], and toward that end we've added the
INFINIBAND_QEDR option. But as we've made the compilation of the
qed/qede infrastructure required for RoCE dependent on the option
we'd be facing linking difficulties in case that QED=y or QEDE=y,
and INFINIBAND_QEDR=m.

To resolve this, we seperate between the INFINIBAND_QEDR option
and the infrastructure support in qed/qede by introducing a new
QED_RDMA option which would be selected by INFINIBAND_QEDR but would
be a boolean instead of a tristate; Following that, the qed/qede is
fixed based on this new option so that all config combinations would
be supported.

Fixes: cee9fbd8 ("qede: add qedr framework")
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: NRam Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other protocols beside the networking driver need the ability
of passing some L2 traffic, usually [although not limited] for the
purpose of some management traffic.
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NRam Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support for dumping and formatting the HW/FW debug data.
Signed-off-by: NTomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.

$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
   text	   data	    bss	    dec	    hex	filename
 127817	  27969	  32800	 188586	  2e0aa	drivers/net/ethernet/qlogic/qed/built-in.o.new
 132474	  27969	  32800	 193243	  2f2db	drivers/net/ethernet/qlogic/qed/built-in.o.old

Miscellanea:

o Change allocs to the generally preferred forms where possible.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make semantic-only adjustments to qed* drivers, such as:
  - Changes in code indentation.
  - Usage of BIT() macro.
  - re-naming of variables.
  - Re-ordering of variable declerations.
  - Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.

Please consider applying this to 'net-next' branch.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

100g support is not available in MSI mode. Failing the driver load in this scenario.

Please consider applying this to `net'.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for configuring the device tx/rx coalescing
timeout values in the order of micro seconds. It also adds APIs for
upper layer drivers for reading/updating the coalescing values.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'MODULE_FIBER' value replaced several other FIBER values
in newer management firmware images, so existing code would
fail to properly reflect its mode.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds in the ecore 2 new personalities in addition to
QED_PCI_ETH - QED_PCI_ISCSI and QED_PCI_ETH_ROCE.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The New QED firmware contains several fixes, including:
  - Wrong classification of packets in 4-port devices.
  - Anti-spoof interoperability with encapsulated packets.
  - Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.

In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc warns about qed_fill_link possibly accessing uninitialized data:

drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]

While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.

This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.

The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.

As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapter can support 100g in both MSIx and INTa, but not in MSI.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This line was indented more than it should be.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>