The code used '&= 0x00002000' when it tried to set the TCO_EN bit, which
obviously didn't set that bit at all, but instead just reset all the
other bits in the SMI_EN register.

This bug seemingly caused various random behavior, with Frans Pop
reporting that X.org just silently hung at startup and Rafael Wysocki
reports the fan spinning with full speed.

See
	http://lkml.org/lkml/2008/12/3/178
	http://bugzilla.kernel.org/show_bug.cgi?id=12162

The problem seems to have been triggered by "[WATCHDOG] iTCO_wdt :
problem with rebooting on new ICH9 based motherboards" (commit
7cd5b08b), but the bogus code existed
before that too (in the "supermicro_old_pre_stop()" function), it just
apparently never showed up due to different logic.

In that commit the broken code got moved around and now gets executed
much more.
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NFrans Pop <elendil@planet.nl>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix setting of max_segment_size and seg_boundary mask for stacked md/dm
devices.

When stacking devices (LVM over MD over SCSI) some of the request queue
parameters are not set up correctly in some cases by default, namely
max_segment_size and and seg_boundary mask.

If you create MD device over SCSI, these attributes are zeroed.

Problem become when there is over this mapping next device-mapper mapping
- queue attributes are set in DM this way:

request_queue   max_segment_size  seg_boundary_mask
SCSI                65536             0xffffffff
MD RAID1                0                      0
LVM                 65536                 -1 (64bit)

Unfortunately bio_add_page (resp.  bio_phys_segments) calculates number of
physical segments according to these parameters.

During the generic_make_request() is segment cout recalculated and can
increase bio->bi_phys_segments count over the allowed limit.  (After
bio_clone() in stack operation.)

Thi is specially problem in CCISS driver, where it produce OOPS here

    BUG_ON(creq->nr_phys_segments > MAXSGENTRIES);

(MAXSEGENTRIES is 31 by default.)

Sometimes even this command is enough to cause oops:

  dd iflag=direct if=/dev/<vg>/<lv> of=/dev/null bs=128000 count=10

This command generates bios with 250 sectors, allocated in 32 4k-pages
(last page uses only 1024 bytes).

For LVM layer, it allocates bio with 31 segments (still OK for CCISS),
unfortunatelly on lower layer it is recalculated to 32 segments and this
violates CCISS restriction and triggers BUG_ON().

The patch tries to fix it by:

 * initializing attributes above in queue request constructor
   blk_queue_make_request()

 * make sure that blk_queue_stack_limits() inherits setting

 (DM uses its own function to set the limits because it
 blk_queue_stack_limits() was introduced later.  It should probably switch
 to use generic stack limit function too.)

 * sets the default seg_boundary value in one place (blkdev.h)

 * use this mask as default in DM (instead of -1, which differs in 64bit)

Bugs related to this:
https://bugzilla.redhat.com/show_bug.cgi?id=471639
http://bugzilla.kernel.org/show_bug.cgi?id=8672Signed-off-by: NMilan Broz <mbroz@redhat.com>
Reviewed-by: NAlasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: NDean Nelson <dcn@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix this sparse warning:

  drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We guarantee 400ns delay at the time of issuing the command.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also while at it:

* Drop unused arguments from ide_complete_power_step().

* Move DEBUG_PM printk() from ide_end_drive_cmd() to
  ide_complete_power_step().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Should fix kernel.org bug #10225:
http://bugzilla.kernel.org/show_bug.cgi?id=10225Reported-by: NMatthias B. <haferfrost@web.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NSergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode.  In order to achieve this:

* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.

* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
  driver for nVidia controllers in Compatibility Mode.

* Teach actual_try_to_identify() and drive_is_ready() about the new flag.

This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).

[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
  and distributions use) it never worked correctly. ]

Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.

More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659
http://bugzilla.kernel.org/show_bug.cgi?id=10216Reported-by: NRemy LABENE <remy.labene@free.fr>
Tested-by: NRemy LABENE <remy.labene@free.fr>
Tested-by: NLars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_release_lock() spits out lots of:

	ide_release_lock: bug

warnings on Atari Falcon.

Fix the ide_release_lock imbalance.
Signed-off-by: NMichael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't overflow the 16-character fb_fix_screeninfo id string (fixes some 
console erasing and blanking artifacts). Have the ID default to "Unknown" 
on machines with no built-in video and no nubus devices. Check for 
fb_alloc_cmap failure.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix module removal bugs of i82875p_edac.  Also i82975x_edac code seems to
have the same module removal bugs as in i82875p_edac.

The problems were:

1. In module removal i82875p_remove_one() is never called.

   Variable i82875p_registered is newer changed from 1, which
   guarantees i82875p_remove_one() is not called (and even if it were
   called, it would be called in wrong order).

   As a result, the edac_mc workque is not stopped and keeps probing.
   If kernel debugging options are not enabled, user may not notice
   anything going wrong.

   if debugging options are enabled and I do "rmmod i82875p_edac", I
   get:

      edac debug: edac_pci_workq_function() checking
      BUG: unable to handle kernel paging request at f882d16f
      ...
      call trace:
       [<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core]
       [<c0233974>] ? run_workqueue+0xd7/0x1a5
       [<c023392f>] ? run_workqueue+0x92/0x1a5
       [<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core]
       [<c0233af9>] ? worker_thread+0xb7/0xc3
       [<c0236a7b>] ? autoremove_wake_function+0x0/0x33
       [<c0233a42>] ? worker_thread+0x0/0xc3
       [<c0236809>] ? kthread+0x3b/0x61
       [<c02367ce>] ? kthread+0x0/0x61
       [<c0204587>] ? kernel_thread_helper+0x7/0x10

   Fix for this is to get rid of needles variable i82875p_registered
   altogether and run i82875p_remove_one() *before*
   pci_unregister_driver().

2. edac_mc_del_mc() uses mci after freeing mci

   edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device().  The
   kobject refcount of mci drops to 0 and mci is freed.  After this
   mci is accessed via debug print and i82875p_remove_one() still
   uses mci->pvt and tries to free mci again with edac_mc_free().

   The fix for this is add kobject_get(&mci->edac_mci_kobj) after
   edac_mc_alloc(). Then the mci is still available after returning
   from edac_mc_del_mc() with refcount 1, and mci->pvt is still
   available. When i82875p_remove_one() finally calls edac_mc_free(),
   this will cause kobject_put() and mci is released properly.
Signed-off-by: NJarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When I do "modprobe i82875p_edac" on my Asus P4C800 MB on kernels 2.6.26
or later, the module load fails due to BAR 0 collision.  On 2.6.25 the
module loads just fine.

The overflow device on the MB seems to be hidden and its resources are not
allocated at normal PCI bus init.  Log shows the missing resource problem:

  EDAC DEBUG: i82875p_probe1()
  PCI: 0000:00:06.0 reg 10 32bit mmio: [fecf0000, fecf0fff]
  pci 0000:00:06.0: device not available because of BAR 0
[0xfecf0000-0xfecf0fff] collisions
  EDAC i82875p: i82875p_setup_overfl_dev(): Failed to enable overflow
device

The patch below fixes this by calling pci_bus_assign_resources() after
the overflow device is revealed and added to the bus. With this patch
I am again able to load and use the module.
Signed-off-by: NJarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The commit aef7db4b fixed the problem with
recursive locking in fb blanking code if blank is caused by user setting
the /sys/class/graphics/fb*/blank.  However this broke the fbcon timeout
blanking.

If you use a driver that defines ->fb_blank operation and at the same time
that driver relies on other driver (e.g.  backlight or lcd class) to blank
the screen, when the fbcon times out and tries to blank the fb, it will
call only fb driver blanker and won't notify the other driver.  Thus FB
output is disabled, but the screen isn't blanked.

Restore fbcon blanking and at the same time apply the proper fix for the
above problem: if fbcon_blank is called with FBINFO_FLAG_USEREVENT, we are
already called through notification from fb_blank, thus we don't have to
blank the fb again.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The engine on some radeon variants locks up if color expansion is called
for non aligned source data.  This patch enables a feature of the core
fbdev to request aligned input pixmaps and uses the HW clipping engine to
clip the output to the requested size

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11875Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NJames Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The spi master driver must have num_chipselect set to allow the bus to
initialise.  Pass this through the platform data.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver.  Fix this
by using spi_master_get_devdata.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.  Tested with mmc-spi.
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Corrects spi_imx driver oops during initialization/probing: can't use
drv_data before it's allocated.
Signed-off-by: NJulien Boibessot <julien.boibessot@armadeus.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send.  The PSC controller holds SS low until the flag is set.

However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer.  This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals.  Fix.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I saw a kernel oops in spidev_remove() when a spidev device was registered
and I unloaded the SPI master driver:

Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01c0c50
Oops: Kernel access of bad area, sig: 11 [#1]
CDSPR
Modules linked in: spi_ppc4xx(-)
NIP: c01c0c50 LR: c01bf9e4 CTR: c01c0c34
REGS: cec89c30 TRAP: 0300   Not tainted  (2.6.27.3izt)
MSR: 00021000 <ME>  CR: 24000228  XER: 20000007
DEAR: 00000004, ESR: 00800000
TASK = cf889040[2070] 'rmmod' THREAD: cec88000
GPR00: 00000000 cec89ce0 cf889040 cec8e000 00000004 cec8e000 ffffffff 00000000
GPR08: 0000001c c0336380 00000000 c01c0c34 00000001 1001a338 100e0000 100df49c
GPR16: 100b54c0 100df49c 100ddd20 100f05a8 100b5340 100efd68 00000000 00000000
GPR24: 100ec008 100f0428 c0327788 c0327794 cec8e0ac cec8e000 c0336380 00000000
NIP [c01c0c50] spidev_remove+0x1c/0xe4
LR [c01bf9e4] spi_drv_remove+0x2c/0x3c
Call Trace:
[cec89d00] [c01bf9e4] spi_drv_remove+0x2c/0x3c
[cec89d10] [c01859a0] __device_release_driver+0x78/0xb4
[cec89d20] [c0185ab0] device_release_driver+0x28/0x44
[cec89d40] [c0184be8] bus_remove_device+0xac/0xd8
[cec89d60] [c0183094] device_del+0x100/0x194
[cec89d80] [c0183140] device_unregister+0x18/0x30
[cec89da0] [c01bf30c] __unregister+0x20/0x34
[cec89db0] [c0182778] device_for_each_child+0x38/0x74
[cec89de0] [c01bf2d0] spi_unregister_master+0x28/0x44
[cec89e00] [c01bfeac] spi_bitbang_stop+0x1c/0x58
[cec89e20] [d908a5e0] spi_ppc4xx_of_remove+0x24/0x7c [spi_ppc4xx]
[...]

IMHO a call to spi_set_drvdata() is missing in spidev_probe(). The patch
below helped.
Signed-off-by: NWolfgang Ocker <weo@reccoware.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The netmos_9xx5_combo type assumes that PCI SSID provides always the
correct value for the number of parallel and serial ports, but there are
indeed broken devices with wrong numbers, which may result in Oops.

This patch simply adds the check of the array range.

Reference: Novell bnc#447067
	https://bugzilla.novell.com/show_bug.cgi?id=447067Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit 50f3beb5 fixed em28xx-alsa
locking schema. However, a backport macro was kept.

This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Label fail_unreg is no longer used.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replaced usb_kill_usb for usb_unlink_usb
(wait until urb to fully stop require USB core to put the calling process to sleep).

Oops:
http://www.kerneloops.org/raw.php?rawid=71799&msgid=Signed-off-by: NDouglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware.  Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.

The wiki page has been updated to contain information on this issue.

  http://ata.wiki.kernel.org/index.php/Known_issuesSigned-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Acked-by: NSergei Shtyltov <sshtylyov@ru.mvista.com>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.

Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
  address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
  allowing 4-byte IO.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume.  This patch updates piix_broken_suspend() such that it
can match such case.  As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.

This is reported by Alexandru Romanescu.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When resizing a CQ, MTTs associated with the old CQE buffer were not
freed.  As a result, if any app used resize CQ repeatedly, all MTTs
were eventually exhausted, which led to all memory registration
operations failing until the driver is reloaded.

Once the RESIZE_CQ command returns successfully from FW, FW no longer
accesses the old CQ buffer, so it is safe to deallocate the MTT
entries used by the old CQ buffer.

Finally, if the RESIZE_CQ command fails, the MTTs allocated for the
new CQEs buffer also need to be de-allocated.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This fix enables ehca device driver to generate flush work completions
even if the application doesn't request completions for all work
requests. The current implementation of ehca will generate flush work
completions for the wrong work requests if an application uses non
signaled work completions.
Signed-off-by: NStefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The error message printed when the eHCA driver prevents memory hotplug
is misleading -- the user might think that hot-removing the lhca,
hotplugging memory, then hot-adding the lhca again will work, but it
actually doesn't.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.

Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

scsi_eh_try_stu() was still using the timeout parameter in the device
which is now not set (i.e. zero filled) meaning that it waited no time
at all for the start unit command to complete (leading the routine to
conclude failure every time).  This lead to a 2.6.27 regression:

http://bugzilla.kernel.org/show_bug.cgi?id=12120

Where firewire devices that were non spec compliant wouldn't spin up.

Fix this by using the block queue timeout value instead.
Reported-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

megaraid_sas sets the timeout in its slave configure routine for devices
on special channels.  This now needs to update the request queue timeout
in block.

Cc: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

ibmvscsi sets the timeout in its slave configure routine for disk
devices.  This now needs to update the request queue timeout in block.

Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

aacraid updates the timeout in its slave configure routine if it is too
small.  This now needs to update the request queue timeout in block.

Cc: AACRAID list <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: NKevin Hao <kexin.hao@windriver.com>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>