There is presently a race condition between the bonding periodic
link monitor and the updating of a slave's speed and duplex.  The former
occurs on a periodic basis, and the latter in response to a driver's
calling of netif_carrier_on.

	It is possible for the periodic monitor to run between the
driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE
event that causes bonding to update the slave's speed and duplex.  This
manifests most notably as a report that a slave is up and "0 Mbps full
duplex" after enslavement, but in principle could report an incorrect
speed and duplex after any link up event if the device comes up with a
different speed or duplex.  This affects the 802.3ad aggregator
selection, as the speed and duplex are selection criteria.

	This is fixed by updating the speed and duplex in the periodic
monitor, prior to using that information.

	This was done historically in bonding, but the call to
bond_update_speed_duplex was removed in commit 876254ae ("bonding:
don't call update_speed_duplex() under spinlocks"), as it might sleep
under lock.  Later, the locking was changed to only hold RTNL, and so
after commit 876254ae ("bonding: don't call update_speed_duplex()
under spinlocks") this call is again safe.
Tested-by: N"Tantilov, Emil S" <emil.s.tantilov@intel.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: dingtianhong <dingtianhong@huawei.com>
Fixes: 876254ae ("bonding: don't call update_speed_duplex() under spinlocks")
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current logic in bond_arp_rcv will accept an incoming ARP for
validation if (a) the receiving slave is either "active" (which includes
the currently active slave, or the current ARP slave) or, (b) there is a
currently active slave, and it has received an ARP since it became active.
For case (b), the receiving slave isn't the currently active slave, and is
receiving the original broadcast ARP request, not an ARP reply from the
target.

	This logic can fail if there is no currently active slave.  In
this situation, the ARP probe logic cycles through all slaves, assigning
each in turn as the "current_arp_slave" for one arp_interval, then setting
that one as "active," and sending an ARP probe from that slave.  The
current logic expects the ARP reply to arrive on the sending
current_arp_slave, however, due to switch FDB updating delays, the reply
may be directed to another slave.

	This can arise if the bonding slaves and switch are working, but
the ARP target is not responding.  When the ARP target recovers, a
condition may result wherein the ARP target host replies faster than the
switch can update its forwarding table, causing each ARP reply to be sent
to the previous current_arp_slave.  This will never pass the logic in
bond_arp_rcv, as neither of the above conditions (a) or (b) are met.

	Some experimentation on a LAN shows ARP reply round trips in the
200 usec range, but my available switches never update their FDB in less
than 4000 usec.

	This patch changes the logic in bond_arp_rcv to additionally
accept an ARP reply for validation on any slave if there is a current ARP
slave and it sent an ARP probe during the previous arp_interval.

Fixes: aeea64ac ("bonding: don't trust arp requests unless active slave really works")
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace 'goto' with 'return' to remove unnecessary check at label:
err_undo_flags.

The reason is that 'err_undo_flags' do two things for the first slave device:
1.revert bond mac address if it is set by the slave device.
2.revert bond device type if it's not ARPHRD_ETHER.

It's not necessary for the following three places, they changed neither bond
mac address nor type. It's straightforward to return directly.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove some redudant brackets, use sizeof(*) instead of sizeof(struct x).
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_dbg() will add bond device name, it will be helpful if we print
slave device name.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sample output with this set applied for an active-backup bond:

$ cat /sys/devices/virtual/net/bond0/lower_p7p1/statistics/rx_nohandler
16568
$ cat /sys/devices/virtual/net/bond0/lower_p5p2/statistics/rx_nohandler
16583
$ cat /sys/devices/virtual/net/bond0/statistics/rx_nohandler
33151

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: netdev@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 1f718f0f ("bonding: populate neighbour's private on enslave")
undoes the fix provided by commit c2edacf8 ("bonding / ipv6: no addrconf
for slaves separately from master") by effectively setting the slave flag
after the slave has been opened.  If the slave comes up quickly enough, it
will go through the IPv6 addrconf before the slave flag has been set and
will get a link local IPv6 address.

In order to ensure that addrconf knows to ignore the slave devices on state
change, set IFF_SLAVE before dev_open() during bonding enslavement.

Fixes: 1f718f0f ("bonding: populate neighbour's private on enslave")
Signed-off-by: NKarl Heiss <kheiss@gmail.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.

This patch:
  - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
    NETIF_F_ALL_CSUM is being used as a mask).
  - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
    use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not necessary to use two brackets. As such, the redudant brackets
are removed.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be correct and symmetric to enslave and set inactive flags during release.
That gives LAG offload drivers - lower state change listeners - possibility
to do proper cleanup.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let netdev notifier listeners know about link and slave state change.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to state notifications.

We allow caller to indicate if the notification should happen now or later,
depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify
function (similar to bond_slave_state_notify) which is later on called
with rtnl mutex and goes over slaves and executes delayed notification.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize netdev_lag_upper_info structure by TX type according to
current bonding mode and pass it along via netdev_master_upper_dev_link.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliminate netdev_master_upper_dev_link_private and pass priv directly as
a parameter of netdev_master_upper_dev_link.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 7d5cd2ce529b, when bond_enslave fails on devices that
are not ARPHRD_ETHER, if needed, it resets the bonding device back to
ARPHRD_ETHER by calling ether_setup.

	Unfortunately, ether_setup clobbers dev->flags, clearing IFF_UP
if the bond device is up, leaving it in a quasi-down state without
having actually gone through dev_close.  For bonding, if any periodic
work queue items are active (miimon, arp_interval, etc), those will
remain running, as they are stopped by bond_close.  At this point, if
the bonding module is unloaded or the bond is deleted, the system will
panic when the work function is called.

	This panic is resolved by calling dev_close on the bond itself
prior to calling ether_setup.

Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 7d5cd2ce ("bonding: correctly handle bonding type change on enslave failure")
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old logic of updating state-machine is not required since
ad_update_actor_keys() does it implicitly. The only loss is
the notification differentiation between speed vs. duplex
change. Now only one unified notification is printed.
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If using a sixtofour device on top of a bonding device,
skb segmentation of TCP traffic is done right before calling
bonding xmit, because bonding only enables TSO for IPv4.

This patch improves single flow performance by about 120 % on my hosts,
because segmentation is deferred right before calling slave xmit.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If skb carries a l4 hash, no need to perform a flow dissection.

Performance is slightly better :

lpaa5:~# ./super_netperf 200 -H lpaa6 -t TCP_RR -l 100
2.39012e+06
lpaa5:~# ./super_netperf 200 -H lpaa6 -t TCP_RR -l 100
2.39393e+06
lpaa5:~# ./super_netperf 200 -H lpaa6 -t TCP_RR -l 100
2.39988e+06

After patch :

lpaa5:~# ./super_netperf 200 -H lpaa6 -t TCP_RR -l 100
2.43579e+06
lpaa5:~# ./super_netperf 200 -H lpaa6 -t TCP_RR -l 100
2.44304e+06
lpaa5:~# ./super_netperf 200 -H lpaa6 -t TCP_RR -l 100
2.44312e+06
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flags argument will allow control of the dissection process (for
instance whether to parse beyond L3).
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is rcu_read_unlock_bh() which triggers a warning when irqs are
disabled. ndo_poll_controller should run with irqs disabled always so we
can drop the rcu_read_lock_bh.

[   98.502922] bond0: making interface eth1 the new active one
[   98.503039] ------------[ cut here ]------------
[   98.503039] WARNING: CPU: 0 PID: 1744 at kernel/softirq.c:150 __local_bh_enable_ip+0x96/0xc0()
[   98.503039] Modules linked in: bonding(OE) rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache netconsole ppdev joydev parport_pc serio_raw parport i2c_piix4 video acpi_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc virtio_net e1000 ata_generic pcnet32 mii virtio_pci virtio_ring virtio pata_acpi
[   98.503039] CPU: 0 PID: 1744 Comm: ifenslave Tainted: G           OE   4.2.0-rc7+ #56
[   98.503039] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   98.503039]  0000000000000000 00000000e96ba230 ffff880020c236b8 ffffffff8183f105
[   98.503039]  0000000000000000 0000000000000000 ffff880020c236f8 ffffffff810a9496
[   98.503039]  ffff88002ea99e08 0000000000000200 ffffffffa02a8e06 ffff88002ea99e08
[   98.503039] Call Trace:
[   98.503039]  [<ffffffff8183f105>] dump_stack+0x4c/0x65
[   98.503039]  [<ffffffff810a9496>] warn_slowpath_common+0x86/0xc0
[   98.503039]  [<ffffffffa02a8e06>] ? bond_poll_controller+0x146/0x250 [bonding]
[   98.503039]  [<ffffffff810a95ca>] warn_slowpath_null+0x1a/0x20
[   98.503039]  [<ffffffff810ae376>] __local_bh_enable_ip+0x96/0xc0
[   98.503039]  [<ffffffffa02a8e2f>] bond_poll_controller+0x16f/0x250 [bonding]
[   98.503039]  [<ffffffffa02a8cf3>] ? bond_poll_controller+0x33/0x250 [bonding]
[   98.503039]  [<ffffffff810feaed>] ? trace_hardirqs_off+0xd/0x10
[   98.503039]  [<ffffffff81848afb>] ? _raw_spin_unlock_irqrestore+0x5b/0x60
[   98.503039]  [<ffffffff816ec48e>] netpoll_poll_dev+0x6e/0x350
[   98.503039]  [<ffffffff816eb977>] ? netpoll_start_xmit+0x137/0x1d0
[   98.503039]  [<ffffffff816b2e8b>] ? __alloc_skb+0x5b/0x210
[   98.503039]  [<ffffffff816ec89d>] netpoll_send_skb_on_dev+0x12d/0x2a0
[   98.503039]  [<ffffffff816eccde>] netpoll_send_udp+0x2ce/0x430
[   98.503039]  [<ffffffffa0190850>] write_msg+0xb0/0xf0 [netconsole]
[   98.503039]  [<ffffffff81116b63>] call_console_drivers.constprop.25+0x133/0x260
[   98.503039]  [<ffffffff81117934>] console_unlock+0x2f4/0x580
[   98.503039]  [<ffffffff81117ea5>] ? vprintk_emit+0x2e5/0x630
[   98.503039]  [<ffffffff81117ee5>] vprintk_emit+0x325/0x630
[   98.503039]  [<ffffffff81118379>] vprintk_default+0x29/0x40
[   98.503039]  [<ffffffff8183de4f>] printk+0x55/0x6b
[   98.503039]  [<ffffffff816c754c>] __netdev_printk+0x16c/0x260
[   98.503039]  [<ffffffff816c7a12>] netdev_info+0x62/0x80
[   98.503039]  [<ffffffffa02ab464>] bond_change_active_slave+0x134/0x6a0 [bonding]
[   98.503039]  [<ffffffffa02aba95>] bond_select_active_slave+0xc5/0x310 [bonding]
[   98.503039]  [<ffffffffa02aeb78>] bond_enslave+0x1088/0x10c0 [bonding]
[   98.503039]  [<ffffffffa02af46b>] bond_do_ioctl+0x37b/0x400 [bonding]
[   98.503039]  [<ffffffff81101d8d>] ? trace_hardirqs_on+0xd/0x10
[   98.503039]  [<ffffffff816dc437>] ? rtnl_lock+0x17/0x20
[   98.503039]  [<ffffffff816e5fd1>] dev_ifsioc+0x331/0x3e0
[   98.503039]  [<ffffffff816e62dc>] dev_ioctl+0xec/0x6c0
[   98.503039]  [<ffffffff816a6c6a>] sock_do_ioctl+0x4a/0x60
[   98.503039]  [<ffffffff816a7300>] sock_ioctl+0x1c0/0x250
[   98.503039]  [<ffffffff81271bfe>] do_vfs_ioctl+0x2ee/0x540
[   98.503039]  [<ffffffff810fd943>] ? up_read+0x23/0x40
[   98.503039]  [<ffffffff81070993>] ? __do_page_fault+0x1d3/0x420
[   98.503039]  [<ffffffff8127e246>] ? __fget_light+0x66/0x90
[   98.503039]  [<ffffffff81271ec9>] SyS_ioctl+0x79/0x90
[   98.503039]  [<ffffffff8184936e>] entry_SYSCALL_64_fastpath+0x12/0x76
[   98.503039] ---[ end trace 00cfa804b0670051 ]---

Fixes: 616f4541 ("bonding: implement bond_poll_controller()")
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhil Sutter <phil@nwl.cc>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the first slave is added (such as during bootup) the first
gratuitous ARP gets dropped. We don't see this drop during a failover.
The packet gets dropped in qdisc (noop_enqueue).

The fix is to delay the sending of gratuitous ARPs till the bond dev's
carrier is present.

It can also be worked around by setting num_grat_arp to more than 1.
Signed-off-by: NVenkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:

1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
   bond0 has the same mac address with eth0, it is MAC1.

2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
   eth1 is backup, eth1 has MAC2.

3) ifconfig eth0 down
   eth1 became active slave, bond will swap MAC for eth0 and eth1,
   so eth1 has MAC1, and eth0 has MAC2.

4) ifconfig eth1 down
   there is no active slave, and eth1 still has MAC1, eth2 has MAC2.

5) ifconfig eth0 up
   the eth0 became active slave again, the bond set eth0 to MAC1.

Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.

This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Tested-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
 Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
    link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)

 After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[  908.963051] eql: event: 9
[  908.963052] eql: IFF_SLAVE
[  908.963054] eql: event: 2
[  908.963056] eql: IFF_SLAVE
[  908.963058] eql: event: 6
[  908.963059] eql: IFF_SLAVE
[  908.963110] bond0: Releasing active interface eql
[  908.976168] bond0: Destroying bond bond0
[  908.976266] bond0 (unregistering): Released all slaves
[  908.984097] ------------[ cut here ]------------
[  908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[  908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[  908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]

[  908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G        W  O
4.2.0-rc2+ #8
[  908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  908.984172]  0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[  908.984175]  ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[  908.984178]  ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[  908.984181] Call Trace:
[  908.984188]  [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[  908.984193]  [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[  908.984196]  [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[  908.984199]  [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[  908.984205]  [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[  908.984208]  [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[  908.984217]  [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[  908.984225]  [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[  908.984228]  [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[  908.984232]  [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[  908.984236]  [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[  908.984241]  [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[  908.984244]  [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[  908.984247] ---[ end trace 7c006ed4abbef24b ]---

Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f9399814 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: NCarol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3 ("bonding: Manage /proc/net/bonding/ entries from
                      the netdev events")
Tested-by: NCarol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of these:
drivers/net/bonding//bond_main.c: In function ‘bond_update_slave_arr’:
drivers/net/bonding//bond_main.c:3754:6: warning: variable
‘slaves_in_agg’ set but not used [-Wunused-but-set-variable]
  int slaves_in_agg;
      ^
  CC [M]  drivers/net/bonding//bond_3ad.o
drivers/net/bonding//bond_3ad.c: In function
‘ad_marker_response_received’:
drivers/net/bonding//bond_3ad.c:1870:61: warning: parameter ‘marker’
set but not used [-Wunused-but-set-parameter]
 static void ad_marker_response_received(struct bond_marker *marker,
                                                             ^
drivers/net/bonding//bond_3ad.c:1871:19: warning: parameter ‘port’ set
but not used [-Wunused-but-set-parameter]
      struct port *port)
                   ^
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When "primary_reselect" is set to "failure", primary interface should
not become active until current active slave is down. But if we set first
member of bond device as a "primary" interface and "primary_reselect"
is set to "failure" then whenever primary interface's link get back(up)
it become active slave even if current active slave is still up.

With this patch, "bond_find_best_slave" will not traverse members if
primary interface is not candidate for failover/reselection and current
active slave is still up.
Signed-off-by: NMazhar Rana <mazhar.rana@cyberoam.com>
Signed-off-by: NJay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.

We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.

With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- introduce port fdb obj and generic switchdev_port_fdb_add/del/dump()
- use switchdev_port_fdb_add/del/dump in rocker/team/bonding ndo ops.
- add support for fdb obj in switchdev_port_obj_add/del/dump()
- switch rocker to implement fdb ops via switchdev_ops

v3: updated to sync with named union changes.
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add couple of empty lines on the way.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roopa said remove the feature flag for this series and she'll work on
bringing it back if needed at a later date.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rocker, bonding and team and switch over to the new
switchdev_port_bridge_dellink to avoid duplicating code in each driver.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rocker, bonding, and team can now use the switchdev bridge setlink to parse
raw netlink; no need to duplicate this code in each driver.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port key has three components - user-key, speed-part, and duplex-part.
The LSBit is for the duplex-part, next 5 bits are for the speed while the
remaining 10 bits are the user defined key bits. Get these 10 bits
from the user-space (through the SysFs interface) and use it to form the
admin port-key. Allowed range for the user-key is 0 - 1023 (10 bits). If
it is not provided then use zero for the user-key-bits (default).

It can set using following example code -

   # modprobe bonding mode=4
   # usr_port_key=$(( RANDOM & 0x3FF ))
   # echo $usr_port_key > /sys/class/net/bond0/bonding/ad_user_port_key
   # echo +eth1 > /sys/class/net/bond0/bonding/slaves
   ...
   # ip link set bond0 up
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
     * fixed up context from change in ad_actor_sys_prio patch]
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In an AD system, the communication between actor and partner is the
business between these two entities. In the current setup anyone on the
same L2 can "guess" the LACPDU contents and then possibly send the
spoofed LACPDUs and trick the partner causing connectivity issues for
the AD system. This patch allows to use a random mac-address obscuring
it's identity making it harder for someone in the L2 is do the same thing.

This patch allows user-space to choose the mac-address for the AD-system.
This mac-address can not be NULL or a Multicast. If the mac-address is set
from user-space; kernel will honor it and will not overwrite it. In the
absence (value from user space); the logic will default to using the
masters' mac as the mac-address for the AD-system.

It can be set using example code below -

   # modprobe bonding mode=4
   # sys_mac_addr=$(printf '%02x:%02x:%02x:%02x:%02x:%02x' \
                    $(( (RANDOM & 0xFE) | 0x02 )) \
                    $(( RANDOM & 0xFF )) \
                    $(( RANDOM & 0xFF )) \
                    $(( RANDOM & 0xFF )) \
                    $(( RANDOM & 0xFF )) \
                    $(( RANDOM & 0xFF )))
   # echo $sys_mac_addr > /sys/class/net/bond0/bonding/ad_actor_system
   # echo +eth1 > /sys/class/net/bond0/bonding/slaves
   ...
   # ip link set bond0 up
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
[jt: fixed up style issues reported by checkpatch]
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows user to randomize the system-priority in an ad-system.
The allowed range is 1 - 0xFFFF while default value is 0xFFFF. If user
does not specify this value, the system defaults to 0xFFFF, which is
what it was before this patch.

Following example code could set the value -
    # modprobe bonding mode=4
    # sys_prio=$(( 1 + RANDOM + RANDOM ))
    # echo $sys_prio > /sys/class/net/bond0/bonding/ad_actor_sys_prio
    # echo +eth1 > /sys/class/net/bond0/bonding/slaves
    ...
    # ip link set bond0 up
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
     * changed how the default value is set in bond_check_params(), this
       makes the default consistent between what gets set for a new bond
       and what the default is claimed to be in the bonding options.]
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>