This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.

The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.

As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: NMika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Eliminate OMAP_MAX_NR_PORTS

Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.

Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.

This was done with:

#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"

for header in $headers; do
	old="#include <mach\/$header"
	new="#include <plat\/$header"
	for dir in $omap_dirs; do
		find $dir -type f -name \*.[chS] | \
			xargs sed -i "s/$old/$new/"
	done
	find drivers/ -type f -name \*omap*.[chS] | \
		xargs sed -i "s/$old/$new/"
	for file in $other_files; do
		sed -i "s/$old/$new/" $file
	done
done

for header in $(ls $mach_dir_old/*.h); do
	git mv $header $plat_dir_new/
done
Signed-off-by: NTony Lindgren <tony@atomide.com>

Most board-*.c files read configuration data from the bootloader in
their .init_machine() function.  This needs to happen earlier, at some
point before omap2_init_common_hw() is called.  This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.

Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path.  Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.

OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention.  The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup.  The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.

While the activity timer is active, the smart-idle mode of the UART is
also disabled.  This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.

Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.

In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.

Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.

Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)

Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds common function to enable/disable omap2/3 uart
clocks. Enabled uarts are passed by bootloader in atags and clocks for
these enabled uarts are touched.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires.  Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Start adding 24xx support by Paul Mundt
- Clean-up of cpu detection by Dirk Behme and Tony Lindgren
- Add DSP header by Toshihiro Kobayashi
- Add support for mtd-xip by Vladimir Barinov
- Add various new mux registers
- Move OMAP specific serial defines back to serial.h
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>