- 11 7月, 2007 10 次提交
-
-
由 Ilpo Järvinen 提交于
Got bored to always recompile it for no reason. Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add management firmware version for ethtool -i. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
In addition to the periodic heartbeat, we're adding a heartbeat request interrupt when the heartbeat is late. This is needed during netpoll where the timer is not available. -rt kernels will also benefit since the timer is not as accurate. [ We discussed this patch last time and we decided that the -rt kernel problem alone did not justify this patch. I think the netpoll problem makes this patch necessary. ] Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Spurious interrupts are often encountered especially on systems using the 8259 PIC mode. This is because the I/O write to deassert the interrupt is posted and won't get to the chip immediately. As a result, the IRQ may remain asserted after the IRQ handler exits, causing spurious interrupts. Add read back to flush the I/O write to deassert the IRQ immediately. We also store the last_status_idx immediately in the IRQ handler to help detect whether the interrupt is ours or not when the IRQ is entered again before ->poll gets called. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Modify the link up dmesg to report remote copper or Serdes link. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Modify the driver's ethtool_ops->get_settings and set_settings functions to support remote PHY. Users control the remote copper PHY settings by specifying link settings for the tp (twisted pair) port. The nway_reset function is also modified to support remote PHY. mii-tool operations are not supported on remote PHY and we will return -EOPNOTSUPP. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
In blade servers, the Serdes PHY in 5708S can control the remote copper PHY through autonegotiation on the backplane. This patch adds the logic to interface with the firmware to control the remote PHY autonegotiation and to handle remote PHY link events. When remote PHY is present, the 5708S Serdes device practically becomes a copper device with full control over the 1000Base-T link settings. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Put existing code to setup the default link settings in this new function. This makes it easier to support the remote PHY feature in the next few patches. Also change ETHTOOL_ALL_FIBRE_SPEED to include 2500Mbps if supported. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
The existing model for checksum offload does not correctly handle devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag implies device can do any arbitrary protocol. This patch: * adds NETIF_F_IPV6_CSUM for those devices * fixes bnx2 and tg3 devices that need it * add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO) * fixes assumptions about NETIF_F_ALL_CSUM in nat * adjusts bridge union of checksumming computation Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 6月, 2007 5 次提交
-
-
由 Michael Chan 提交于
Update to version 1.5.11. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The statistics block DMA on 5708 can be messed up occasionally on the average of about once per hour. If the user is reading the counters within one second after the corruption, the counters will be all messed up. One second later, the counters will be ok again until the next corruption occurs. The workaround is to disable the periodic statistics DMA. Instead, we manually trigger the DMA once a second in bnx2_timer(). This manual trigger of the DMA avoids the problem. As a consequence, we can only allow 0 or 1 second settings for ethtool -C statistics block. Thanks to Jean-Daniel Pauget <jd@disjunkt.com> and CaT <cat@zip.com.au> for reporting this rare problem. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add missing code to enable DMA on 5709 A1. The bit is a no-op on A0 and therefore can be set on all 5709 chips. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
For correctness, we need to wait for the MEM_INIT bit to be cleared in the BNX2_CTX_COMMAND register before proceeding. [Added return -EBUSY when the MEM_INIT bit doesn't clear, suggested by Jeff Garzik.] Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
There's a bug in the driver that only initializes half of the context memory on the 5708. Surprisingly, this works most of the time except for some occasional netdev watchdogs when sending a lot of 64-byte packets. The fix is to add the missing code to initialize the 2nd halves of all context memory. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 6月, 2007 1 次提交
-
-
由 Stephen Hemminger 提交于
Many drivers had code that did kill_vid, but they weren't doing vlan filtering. With new API the stub is unneeded unless device sets NETIF_F_HW_VLAN_FILTER. Bad habit: I couldn't resist fixing a couple of nearby style things in acenic, and forcedeth. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 04 5月, 2007 15 次提交
-
-
由 Michael Chan 提交于
Remove the check for skb->len greater than MTU when doing TSO. When the destination has a smaller MSS than the source, a TSO packet may be smaller than the MTU at the source and we still need to process it as a TSO packet. Thanks to Brian Ristuccia <bristuccia@starentnetworks.com> for reporting the problem. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Update version to 1.5.10. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix the code to print PCI or PCIE bus information for all devices. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The 5709 supports the one-shot MSI handler similar to some of the tg3 chips. In this mode, the MSI disables itself automatically until it is re-enabled at the end of NAPI poll. Put the request_irq/free_irq logic in common procedures. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Restructure by adding bnx2_phy_event_is_set() to make code cleaner and easier to understand. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The indirect register access method will be used by more than one caller in BH context (NAPI poll and timer), so a spinlock is required. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add PCI ID and code to support the 5709 Serdes PHY. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add some common procedures to handle enabling and disabling 2.5G. Add some missing code to resolve flow control. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The 5709 Serdes device uses non-standard MII register offsets. This re-structuring will make it easier to support 5709 Serdes. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
This is needed to save the MSI state which will be lost during suspend. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Hot-plug scripts can call bnx2_open() as soon as register_netdev() is called in bnx2_init_one(). We need to call pci_set_drvdata() and setup everything before calling register_netdev(). netif_carrier_off() also needs to be moved to bnx2_open() to avoid race conditions with the irq. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The internal PCIE-to-PCIX bridge of the 5708 has the same 40-bit DMA limitation as some of the tg3 chips. Set dma_mask and persistent DMA mask to 40-bit to workaround. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Tweak registers and memory test range for 5709. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The device may be in D3hot state and should not allow MII register access. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 4月, 2007 5 次提交
-
-
由 Arnaldo Carvalho de Melo 提交于
To clearly state the intent of copying from linear sk_buffs, _offset being a overly long variant but interesting for the sake of saving some bytes. Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
-
由 Arnaldo Carvalho de Melo 提交于
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to avoid the longer, open coded equivalent. Ditched a no-op in bnx2 in the process. I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()... Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open coded skb->nh.iph uses, now to go after the rest... Just out of curiosity, here are the idioms found to get the same result: skb->nh.iph->ihl << 2 skb->nh.iph->ihl<<2 skb->nh.iph->ihl * 4 skb->nh.iph->ihl*4 (skb->nh.iph)->ihl * sizeof(u32) Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 4月, 2007 1 次提交
-
-
由 Michael Chan 提交于
Tweak a register setting to prevent the tx mailbox from halting. Update version to 1.5.8. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 4月, 2007 1 次提交
-
-
由 Michael Chan 提交于
The nvram dword alignment logic was broken when writing less than 4 bytes on a non-aligned offset. It was missing logic to round the length to 4 bytes. The page erase code is also moved so that it is only called when using non-buffered flash for better code clarity. Update version to 1.5.7. Based on initial patch from Tony Cureington <tony.cureington@hp.com>. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 3月, 2007 1 次提交
-
-
由 Michael Chan 提交于
bnx2_has_work()'s logic is flawed and can cause the driver to miss a link event. The fix is to compare the status block's attn_bits and attn_bits_ack to determine if there is a link event. Update version to 1.5.6. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 3月, 2007 1 次提交
-
-
由 Dan Aloni 提交于
This patch splits the vlan_group struct into a multi-allocated struct. On x86_64, the size of the original struct is a little more than 32KB, causing a 4-order allocation, which is prune to problems caused by buddy-system external fragmentation conditions. I couldn't just use vmalloc() because vfree() cannot be called in the softirq context of the RCU callback. Signed-off-by: NDan Aloni <da-x@monatomic.org> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-