DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.

(Queueing function signature has changed in order to give
 a build failure instead of silent functional changes due
 to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

By replacing an extra do_IRQ with a goto, the assembly shrinks
from 260 to 212 bytes (gcc-4.3.4).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Eliminate the sharing of IRQ names among the differenct Alchemy
variants.  IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.

This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!

Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.

Run-tested on DB1200.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Extract the alchemy chip variant from c0_prid register.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/14/
Patchwork: http://patchwork.linux-mips.org/patch/707/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Raise RTCMATCH2 interrupt priority in case it is used as the system
timer tick.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Alchemy hardware provides a method to prioritize interrupts
on a controller by assigning them to a differenct core request line.
Assign usb device request interrupt to IC0 Request 0 (which has
highest priority in the core and the dispatcher) and others to
Request 1.  The explicit check for usb device request occurrence
should be obsolete now.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Rewritten XXS1500 PCMCIA socket driver, standalone (doesn't depend on
au1000_generic.c) and added carddetect IRQ support.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
        - supports Db1000, DB/PB1100/1500/1550/1200.
        - support for carddetect and statuschange IRQs.
        - pcmcia socket mem/io/attr areas and irqs passed through
          platform resource information.
        - doesn't freeze system during card insertion/ejection like
          the one it replaces.
        - boardtype is automatically detected using BCSR ID register.

Run-tested on the DB1200.

Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

remove board_init_irq():  On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.

Some small irqmap.c files have been folded into board_setup files.

Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All Alchemy development boards have external CPLDs with a few registers
in them.  They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.

This patch
- adds a primitive facility to initialize and use these external
  registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
  functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
  headers in a central place.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Seen on rm200_defconfig for example:

  CC      arch/mips/boot/compressed/decompress.o
/home/ralf/src/linux/upstream-linus/arch/mips/boot/compressed/decompress.c: In function ‘decompress_kernel’:
/home/ralf/src/linux/upstream-linus/arch/mips/boot/compressed/decompress.c:116: error: implicit declaration of function ‘decompress’
make[3]: *** [arch/mips/boot/compressed/decompress.o] Error 1
make[2]: *** [vmlinuz.ecoff] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds following changes:-
	1) add sub device configuration data for TVP5146 used by vpfe capture
	2) registers platform devices for vpfe_capture, isif and vpss
	3) defines hardware resources for the devices listed under 2)
	4) defines clock aliase for isif driver
	5) adding setup_pinmux() for isif
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NMurali Karicheri <mkaricheri@gmail.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

pxa_camera init() callback is sometimes abused to setup MFP for PXA CIF, or
even to request GPIOs to be used by the camera *sensor*. These initializations
can be performed statically in machine init functions.

The current semantics for this init() callback is ambiguous anyways, it is
invoked in pxa_camera_activate(), hence at device node open, but its users use
it like a generic initialization to be done at module init time (configure
MFP, request GPIOs for *sensor* control).
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch removes "buswidth" struct member, and sets the default buswidth
to the natively supported 10 bit. You can select 8 bit buswidth by new flag.
This patch also modify ap325rxa/migor setup.c
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This adds platform code for ccdc driver on DM355 and DM6446.

1) new ccdc platform devices added
2) added clock aliases master and slave for CCDC clocks
3) added dm355_ccdc_setup_pinmux() pin-mux setup hook in dm355 ccdc driver platform data
Reviewed-by: NVaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMuralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

CONFIG_PM is always set on SH-Mobile these days so
get rid of the unused LED setup code.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Allow building the ecovec board support code
even though I2C support is disabled.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds board specific r-standby resume code
for ecovec.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds board specific r-standby resume code
for ms7724se.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add code to save/restore registers during
R-standby sleep on SH-Mobile processors.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

commit ff097ddd (x86/PCI: MMCONFIG: manage pci_mmcfg_region as a
list, not a table) introduced a nasty memory corruption when
pci_mmcfg_list is empty.

pci_mmcfg_check_end_bus_number() dereferences pci_mmcfg_list.prev even
when the list is empty. The following write hits some variable near to
pci_mmcfg_list.

Further down a similar problem exists, where cfg->list.next is
dereferenced unconditionally and a comparison with some variable near
to pci_mmcfg_list happens.

Add a check for the last element into the for_each_entry() loop and
remove all the other crappy logic which is just a leftover of the old
array based code which was replaced by the list conversion.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

KEYSC::SCN register of SH7724 is 3bit.
Thus, scan_timing should be 0 - 7 here.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Set the PCI CLS early in the boot process to prevent
device failures. In pcibios_set_master use the new
pci_cache_line_size instead of a hard-coded value.
Signed-off-by: NCarlos O'Donell <carlos@codesourcery.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NKyle McMartin <kyle@redhat.com>

Trailing semicolon causes compilation involving out_le32() to fail.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Revert the change made to arch/ia64/sn/kernel/setup.c by commit
204fba4a as it breaks the build.

Fixing the build the b94b0808 way
breaks xpc because genksyms then fails to generate an CRC for
per_cpu____sn_cnodeid_to_nasid because of limitations in the
generic genksyms code.
Signed-off-by: NHedi Berriche <hedi@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The main benefit of using ACPI host bridge window information is that
we can do better resource allocation in systems with multiple host bridges,
e.g., http://bugzilla.kernel.org/show_bug.cgi?id=14183

Sometimes we need _CRS information even if we only have one host bridge,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/341681

Most of these systems are relatively new, so this patch turns on
"pci=use_crs" only on machines with a BIOS date of 2008 or newer.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge.  We've increased this size
several times when the table overflowed.

But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.

This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode.  Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.

I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture.  This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.

This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This hooks up the SET/GET_UNALIGN_CTL knobs cribbing the bulk of it from
the PPC and ia64 implementations. The thread flags happen to be the
logical inverse of what the global fault mode is set to, so this works
out pretty cleanly. By default the global fault mode is used, with tasks
now being able to override their own settings via prctl().
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Follow the ARM change, which is what our alignment helpers are based on
in the first place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.

Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.

Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds the Intel Cougar Point (PCH) LPC and SMBus Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Ignoring the last page when ddr size is 128M. Cached accesses to last page
is causing the processor to prefetch using address above 128M stepping out
of the DDR address space.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/981/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>