Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Hummingboard has no over current hardware, so disable the over current
detection for both ports.

Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The following error is seen after a suspend/resume cycle on a mx53qsb with a
MC34708 PMIC:

root@freescale /$ echo mem > /sys/power/state
[   32.630592] PM: Syncing filesystems ... done.
[   32.643924] Freezing user space processes ... (elapsed 0.001 seconds) done.
[   32.652384] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[   32.679156] PM: suspend of devices complete after 13.113 msecs
[   32.685128] PM: suspend devices took 0.030 seconds
[   32.696109] PM: late suspend of devices complete after 6.133 msecs
[   33.313032] mc13xxx 0-0008: Failed to read IRQ status: -110
[   33.322009] PM: noirq suspend of devices complete after 619.667 msecs
[   33.328544] Disabling non-boot CPUs ...
[   33.335031] PM: noirq resume of devices complete after 2.352 msecs
[   33.842940] mc13xxx 0-0008: Failed to read IRQ status: -110
[   33.976095] [sched_delayed] sched: RT throttling activated
[   33.984804] PM: early resume of devices complete after 642.642 msecs
[   34.352954] mc13xxx 0-0008: Failed to read IRQ status: -110
[   34.862910] mc13xxx 0-0008: Failed to read IRQ status: -110
[   34.996595] PM: resume of devices complete after 1005.367 msecs
[   35.372925] mc13xxx 0-0008: Failed to read IRQ status: -110
[   35.882911] mc13xxx 0-0008: Failed to read IRQ status: -110
[   35.955707] PM: resume devices took 1.970 seconds
[   35.960445] Restarting tasks ... done.
[   35.993386] fec 63fec000.ethernet eth0: Link is Down
[   36.392980] mc13xxx 0-0008: Failed to read IRQ status: -110
[   36.902908] mc13xxx 0-0008: Failed to read IRQ status: -110
[   36.953036] ata1: SATA link down (SStatus 0 SControl 300)
[   37.412922] mc13xxx 0-0008: Failed to read IRQ status: -110
[   37.922906] mc13xxx 0-0008: Failed to read IRQ status: -110
[   37.993379] fec 63fec000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   38.432938] mc13xxx 0-0008: Failed to read IRQ status: -110
[   38.942920] mc13xxx 0-0008: Failed to read IRQ status: -110
[   39.452933] mc13xxx 0-0008: Failed to read IRQ status: -110

(flood of this error message continues forever)

Commit 5169df8b ("ARM: dts: i.MX53: add support for MCIMX53-START-R")
missed to configure the IOMUX for the PMIC IRQ pin.

Configure the PMIC IRQ pin so that the suspend/resume sequence behaves cleanly
as expected.

Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The current pinfunc define all uart CTS_B IO port for DCE uart 'CTS_B'
IP port. Since uart IP port 'CTS_B' is output, and it don't need to
set 'SELECT_INPUT' bit.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The VPU on i.MX53 has two distinct clocks for register access and
internal function.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Fixes: fbf970f6 ("ARM: dts: mx53qsb: Enable VPU support")
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NSilvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Previous version had an extra 'fsl' which made the pins not match
any entry.  The console message,

 vf610-pinctrl 40048000.iomuxc: no fsl,pins property in node \
    /soc/aips-bus@40000000/iomuxc@40048000/vf610-twr/esdhc1grp

is displayed without the fix.  The prior version would generally
work as u-boot sets the pins properly for sdhc.  This change allows
Linux sdhc use even if u-boot is built without sdhc support.
Signed-off-by: NBill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Fixes: 0517fe6a ("ARM: dts: vf610-twr: Add support for sdhc1")
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This was caused by commit 5a8da524 ("ARM: dts: exynos5420: add dsi
node"), which conflicted with d51cad7d ("ARM: dts: remove display
power domain for exynos5420").

The DTS addition should never have been merged through the DRM tree in
the first place, and it lacked an ack from the platform maintainer
(who would have known that the disp_pd reference got removed).
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The EHCI and HSIC device tree nodes were added in the wrong place.
Fix them.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds common part of dsi node.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds mipi-phy node for MIPI DSI device.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds socfpga Ethernet filter attributes for multicast
and unicast filters per Synopsys Ethernet IP configuration chosen
by Altera for the Cyclone 5 and Arria SOC FPGAs.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use CPU_METHOD_OF_DECLARE() instead. And declare smp method in dts file.

Changelog:
v6:
  * Use hisilicon,hi3620-smp as enable-method property in Hi3620 dts.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add dts file for Hisilicon x5hd2 development kit board.
Signed-off-by: NHaifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: NJiancheng Xue <jchxue@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
[olof: Rename dts/dtsi to include hisi prefix]
Signed-off-by: NOlof Johansson <olof@lixom.net>

This is the top USB port on the evb (the one closest to the Ethernet
connector).
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

rk3288 has two kind of usb controller; this adds the ehci variant for
host0 and hsic.

At the moment we don't add any phys for these controllers, but the
default settings seem to work OK.

There is a hardware problem in ohci controller which make it
unavailable and host0 controller can only support high-speed devices.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

There is no phy driver that works on the Rockchip board for either USB
host port yet.  For now just hardcode the vbus signal to be on all the
time which makes both the dwc2 host and the EHCI port work.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Working on sound support I noticed the Apalis T30 Evaluation board
device tree missing the more generic Apalis T30 compatible string.
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Indentation of the clock property used a hodgepodge of tabs and spaces.
Make them more consistent (tabs for indentation followed by spaces for
alignment).
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).

After commit 78f87df2
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.

So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This adds the Designware compatible watchdog found on RK3xxx Cortex-A9 SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

We set default pinctrl settings for the uarts in rk3188.dtsi already,
so remove forgotten duplicate.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This patch add missing pinctrl for uart0/1 for Exynos3250. The gpio pin (
uart0_data, uart0_fctl, uart1_data) is only used for UART IP.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch removes duplicat 'interrupt-parent' property for Exynos3250
because exynos3250.dtsi already defined 'interrupt-parent' property
as following:

In arch/arm/boot/dts/exynos3250.dtsi:

	compatible = "samsung,exynos3250";
	interrupt-parent = <&gic>;
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add TMU (Thermal Management Unit) dt node to monitor the high
temperature for Exynos3250.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The IRQB interrupt pin of MAX77686 PMIC is connected to GPX3[2] pin of
Exynos5250 on the Exynos5250 SMDK board. Specify this connection using
interrupts property for the max77686 pmic node.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an Atmel maXTouch instead.
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an s5m8767 instead.
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Commit 9188883f (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.

Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883f (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: NTony Lindgren <tony@atomide.com>

The DMA engine is enabled for all DTs that derive from zynq-7000.dtsi.
There is no need to override the 'status' property in board DTs.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add node describing Zynq's CAN controller.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>

Adds PMU DT node for exynos5260 SoC.
Signed-off-by: NVikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Exynos initialization code now relies on obtaining the PMU address,
so prepare a PMU node for Exynos5410.

Fixes: fce9e5bb ("ARM: EXYNOS: Add support for mapping PMU base
address via DT")
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Update the bindings for touchscreen size.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Update the bindings for touchscreen size.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add a sample DTS which will allow bootup of a board populated
with the BCM7445 chip.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>

The Lenovo Iomega ix4-300d is a 4-Bay sata NAS with dual Gb, USB2.0 & 3.0,
powered by a Marvell Armada XP MV78230 dual core CPU.

http://shop.lenovo.com/us/en/servers/network-storage/lenovoemc/ix4-300d/Signed-off-by: NBenoit Masson <yahoo@perenite.com>
Link: https://lkml.kernel.org/r/1406503839-4662-1-git-send-email-yahoo@perenite.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Define nodes representing the two Cortex A9 CPUs in a bcm21644 SoC.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>