There is no point in keeping around the now unused intc2 code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the sh-specific voyagergx interrupt code to make use
of intc. A lot of "interesting" old cruft gets replaced with intc tables
and some simple demux code.

- All interrupt sources in the sm501 data sheet are now in the header.
- The number and order of IRQ values are disconnected from register bits.
- Interrupt sources now start from IRQ 200.
- set_irq_chained_handler() is now used to hook up the demux function.

In the future it would probably make sense to move the interrupt demuxer
into into the mfd driver, but this is probably a nice step in the right
direction until that happens.

Tested on a R2D-1 board using the serial port hooked up to the sm501.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds single bitmap register support to intc. The current
code only handles 16 and 32 bit registers where a set bit means
interrupt enabled, but this is easy to extend in the future.

The INTC_IRQ() macro is also added to provide a way to hook in
interrupt controllers for FPGAs in boards or companion chips.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes redundant interrupt code for the shmin board which
is using a sh770x processor and 4 IRQ lines as individual interrupts
(IRQ-mode).
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.

Three boards are affected: sh03, snapgear and titan.

The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.

This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: NMarkus Brunner <super.firetwister@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Wire up CPU#0 URAM as node 1 on SH-X3.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the cpu specific interrupt setup code for x3 from
intc2 to intc. New vectors are also added to match the preliminary
information.

Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The intc tables for sh3 currently contain a typo where the bit
fields in IPRD are mixed up for IRQ4 and IRQ5. This patch makes
sure the correct bit fields are used - all according to the
datasheets.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The cache disabling stuff screwed up some of the sh4 nommu
builds, fix it up again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The new intc code handles IRQ3 and IRQ7 in the cpu specific code
already, so there is no reason to duplicate that here.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the cpu specific interrupt setup code for sh7760
from ipr + intc2 to intc. New vectors are also added to match the
information provided by the datasheet.

Vectors for IRQ4-IRQ7 are enabled by default. Use plat_irq_setup_pins()
if pins IRL0-3 should be used in IRLM mode.

The patch also adds the SIM block to the serial port platform data.
Version two of this patch fixes MMCIF problems reported by Manuel Lauss.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the cpu specific interrupt setup code for sh7785
from intc2 to intc. New vectors are also added to match the information
provided by the datasheet.

No IRQ/IRL pin vectors are enabled by default. Use plat_irq_setup_pins()
to select between IRL and IRQ mode.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This reworks the cache mode configuration in Kconfig, and allows for
explicit selection of write-back/write-through/off configurations.
All of the cache flushing routines are optimized away for the off
case.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch makes sure that the sh7710 specific ipsec vector is missing
if building for a sh7712. All according to the datasheet.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a few missing vectors for sh7707. The only interrupt
controller differences between sh7707 and sh7709 seem to be added
vectors for one LCD controller and two PCMCIA slots.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c.  It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.

Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the cpu specific interrupt setup code
for sh7710 from ipr to intc. While at it new vectors are added
to match the information provided by the datasheet. Version two
simplifies the Kconfig part.

Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also adds sh7710 specific platform data for the rtc
driver. The base address of SCIF1 is adjusted to match the
datasheet.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the cpu specific interrupt setup code for
sh7705 from ipr to intc. While at it new vectors are added to
match the information provided by the datasheet.

Vectors for IRQ4 and IRQ5 are enabled by default.

Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also adds sh7705 specific platform data for the rtc driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] ahci: add ATI SB800 PCI IDs
  libata-sff: Fix documentation
  libata: Update the blacklist with a few more devices

This simplifies signalfd code, by avoiding it to remain attached to the
sighand during its lifetime.

In this way, the signalfd remain attached to the sighand only during
poll(2) (and select and epoll) and read(2).  This also allows to remove
all the custom "tsk == current" checks in kernel/signal.c, since
dequeue_signal() will only be called by "current".

I think this is also what Ben was suggesting time ago.

The external effect of this, is that a thread can extract only its own
private signals and the group ones.  I think this is an acceptable
behaviour, in that those are the signals the thread would be able to
fetch w/out signalfd.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

we upgraded the kernel of a nfs-server from 2.6.17.11 to 2.6.22.6. Since
then we get the message

lockd: too many open TCP sockets, consider increasing the number of nfsd threads
lockd: last TCP connect from ^\\236^\É^D

These random characters in the second line are caused by a bug in
svc_tcp_accept.

(Note: there are two previous __svc_print_addr(sin, buf, sizeof(buf))
calls in this function, either of which would initialize buf correctly;
but both are inside "if"'s and are not necessarily executed.  This is
less obvious in the second case, which is inside a dprintk(), which is a
macro which expands to an if statement.)
Signed-off-by: NWolfgang Walter <wolfgang.walter@studentenwerk.mhn.de>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ATI/AMD SB800 shares some device IDs with SB700,
and SB800 adds two more device IDs:0x4394,0x4395.
Signed-off-by: Nhenry su <henry.su.ati@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Code moved to ioread/iowrite but the comment didn't
Also note a posting issue
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [BNX2]: Add PHY workaround for 5709 A1.
  [PPP] L2TP: Fix skb handling in pppol2tp_xmit
  [PPP] L2TP: Fix skb handling in pppol2tp_recv_core
  [PPP] L2TP: Disallow non-UDP datagram sockets
  [PPP] pppoe: Fix double-free on skb after transmit failure
  [PKT_SCHED]: Fix 'SFQ qdisc crashes with limit of 2 packets'
  [NETFILTER]: MAINTAINERS update
  [NETFILTER]: nfnetlink_log: fix sending of multipart messages

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  sky2: version 1.18
  sky2: receive FIFO checking
  sky2: fe+ chip support
  sky2: reorganize chip revision features
  sky2: ethtool speed report bug
  sky2: fix VLAN receive processing (resend)
  phy: export phy_mii_ioctl
  myri10ge: Add support for PCI device id 9

Update version number
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.

As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.

This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: NPierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Initialization of ohci1394 was broken according to one reporter if the
driver was statically linked, i.e. not built as loadable module.  Dmesg:

  PCI: Device 0000:02:07.0 not available because of resource collisions
  ohci1394: Failed to enable OHCI hardware.

This was reported for a Toshiba Satellite 5100-503.  The cause is commit
8df4083c in Linux 2.6.19-rc1 which only
served purposes of early remote debugging via FireWire.  This
functionality is better provided by the currently out-of-tree driver
ohci1394_earlyinit.  Reversal of the commit was OK'd by Andi Kleen.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Add the DIS_EARLY_DAC PHY workaround for 5709 A1.  Without it, link
sometimes does not come up.

Update version to 1.6.5.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes pppol2tp_xmit call skb_cow_head so that we don't modify
cloned skb data.  It also gets rid of skb2 we only need to preserve the
original skb for congestion notification, which is only applicable for
ppp_async and ppp_sync.

The other semantic change made here is the removal of socket accounting
for data tranmitted out of pppol2tp_xmit.  The original code leaked any
existing socket skb accounting.  We could fix this by dropping the
original skb owner.  However, this is undesirable as the packet has not
physically left the host yet.

In fact, all other tunnels in the kernel do not account skb's passing
through to their own socket.  In partciular, ESP over UDP does not do
so and it is the closest tunnel type to PPPoL2TP.  So this patch simply
removes the socket accounting in pppol2tp_xmit.  The accounting still
applies to control packets of course.

I've also added a reminder that the outgoing checksum here doesn't work.
I suppose existing deployments don't actually enable checksums.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function pppol2tp_recv_core doesn't handle non-linear packets properly.
It also fails to check the remote offset field.

This patch fixes these problems.  It also removes an unnecessary check on
the UDP header which has already been performed by the UDP layer.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the addition of UDP-Lite we need to refine the socket check so
that only genuine UDP sockets are allowed through.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I got rid of the second packet in __pppoe_xmit I created
a double-free on the skb because of the goto abort on failure.
This patch removes that.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>