To improve power consumption in idle associated mode FW may lower
RX power. This low linearity mode is acceptable for listening low rate
RX such as beacons and groupcast. The driver enables LPRX only if PM
is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps.
LPRX RSSI threshold is used to limit a range where LPRX is applied.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add prints visible to the user when entering and exiting
thrermal throttling, because so users can tell that the
NIC is getting too hot (and throughput will decrease.)
Signed-off-by: Neytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the D3 firmware crashes, it can be helpful for debugging to
resume the system to get the SRAM snapshot to see why it crashed.
Allow enabling this with a debugfs option.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This function doesn't actually exist, remove its declaration.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The AP mode needs to use the MCAST fifo for the MCAST
frames sent after the DTIM. This fifo needs to be
configured with the same parameters as the VOICE FIFO.

A separate SCD queue is mapped to this fifo - the cab_queue
(cab stands for Content After Beacon). This queue isn't
connected to any station, but rather to the MAC context.
This queue should (and is already) be set as the MCAST
queue - this is part of the of MAC context command.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.

Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.

Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)

Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.

Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add debugfs files to control powersave parameters for testing.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware supports periodic keep alive and beacon monitoring,
so advertise connection monitor offload capability by setting
IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons
notification handler. Call ieee80211_beacon_loss in case of
missed beacons, so AP probing by mac80211 can be triggered.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to avoid NIC destruction due to high temperature,
CT kill will power down the NIC.

To avoid this, thermal throttling will decrease throughput
to prevent the NIC from reaching the temperature at which
CT kill is performed.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Beacon abort is used by device to increase idle dwell time when system
is idle. This algorithm is on top of beacon filtering feature. Enable
beacon abort only if power management is enabled.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.

Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.

Cc: stable@vger.kernel.org [3.9]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The D3 image SRAM is overwritten by the runtime image, so
it can't be accessed after resume. However, it can be very
useful to look at it to know what happened during D3, so
add the ability to store the image and make it available
in debugfs.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In current implementation, the phy context is tightly coupled
with the channel context. This complicates the possibility of
using the same phy context for both netdev interfaces and the P2P
Device interface. To loosen this coupling:

1. Manage all the phy contexts in the mvm op mode, and only save
   the phy context id in the chanctx memory.
2. Reference count the phy contexts and free them only when they
   are not longer used (both by mac80211 and P2P Device).
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add iwl_beacon_filter_cmd struct, disable and enable beacon
filtering as needed.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function just wraps an existing one, remove it.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

1. Quota for the monitor interface should be added only if there is
   a channel context assigned to the interface.
2. In the unassign channel context flow, need to remove the quota
   for the monitor interface binding, before unbinding.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mostly for debugging purposes
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code removed in this patch was used for bring up on
older NICs. No MVM capable fw will ever be released for
older NICs, so remove that code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow to track how BT core updates the driver.
This is required to debug the BT Coexistence mechanism.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The BT-Coex notification is sent by the fw when there are
updates wrt. BT activity. Driver action might be taken
based on the info in this notification.

For now, update the Ack/Cts_kill_msk if HID / SCO / A2DP
profiles are active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Send the PRIO table before the calibrations. This table
tells the fw what priority to give to what (WiFi / BT)
according to events.

Send a hardcoded BT_COEX command to the fw to enable basic
BT coexistence.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When modifying a MAC, we update its beacon system time which
is taken as a base to calculate TBTT. The firmware doesn't use
the new timestamp because the time is never used after the MAC
and broadcast station were added, but it is safer to not rely
on this and avoids the overhead of reading the register every
time the MAC is updated.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the number of addresses (max 5) from the NVM
instead of limiting to 2 artificially.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

7000.c was released as GPL only by mistake: it should be
dual licensed - GPL / BSD.
The file that contains the license in the kernel is COPYING
and not LICENSE.GPL.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make the rssi more accurate by taking in count per-chain AGC
values. Without this, the RSSI reports inaccurate values.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The wakeup packet in the status response is padded out
to a multiple of 4 bytes by the firmware for transfer
to the host, take that into account when checking the
length of the command.

Also, the reported wakeup packet includes the FCS but
the userspace API doesn't, so remove that. If it is a
data packet it is reported as an 802.3 packet but I
forgot to take into account and remove the encryption
head/tail, fix all of that as well.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Newer firmware revisions have a completely new
firmware API. This is the new driver for this
new API.

I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.

Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Amit Beka <amit.beka@intel.com>
Cc: Amnon Paz <amnonx.paz@intel.com>
Cc: Assaf Krauss <assaf.krauss@intel.com>
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Dor Shaish <dor.shaish@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Eytan Lifshitz <eytan.lifshitz@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>