When resetting, phy_state_machine may be accessing the phy through
firmware if the phy is not stopped or disconnected, which will
cause firemware timeout problem because the firmware is busy
processing the reset request.

This patch fixes it by disabling the phy when resetting.

Fixes: b940aeae0ed6 ("net: hns3: never send command queue message to IMP when reset")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hardware sends the HCLGE_VECTOR0_EVENT_RST event through
hclge_misc_irq_handle, currently driver enables misc_vector in
the interrupt handle, and hardware generates the same interrupt
for the same reset event again and again until the reset is
complete, which causes hclge_reset running repeatly problem.

This patch fixes by enabling the misc_vector after reset is
complete.

Fixes: 4ed340ab ("net: hns3: Add reset process in hclge_main")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.

This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing function reset or insmod hns3 dirver after rmmod,
the entries of mac vlan table are not cleared, which may cause
init mac address failed. This patch fixes it by clearing the
old mac address when doing function reset or rmmod hns3 driver.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add checking for new mac address. It doesn't need to config
the mac vlan table if it's already in use.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is only 128 entries for hardware's vf vlan table, when
the vf table is full, the firmware will disable the vf vlan
filter and return a resp_code of HCLGE_VF_VLAN_NO_ENTRY to
driver.

This patch checks the if resp_code from firmware is
HCLGE_VF_VLAN_NO_ENTRY, if yes, then print a warning and
return ok to the caller.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.

The calltrace as follows:
[   93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
 <SNIP>
[   93.278784] Call trace:
[   93.278788]  hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[   93.278790]  hnae3_register_client+0xcc/0x150 [hnae3]
[   93.278801]  hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[   93.278805]  do_one_initcall+0x58/0x160
[   93.278807]  do_init_module+0x64/0x1d8
[   93.278809]  load_module+0x135c/0x15c8
[   93.278811]  SyS_finit_module+0x100/0x118
[   93.278816]  __sys_trace_return+0x0/0x4
[   93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: NXinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: NZhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Signed-off-by: NZhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.

Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.

So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNAE3 module supports kernel nic driver, user nic driver and roce driver,
and there are 3 client types. Driver uses one bit(HNAE3_CLIENT_INITED_B)
to indicate the client initialization state, it will cause confusion
for 3 client types. This patch fixes it by use 3 bits to indicate the
initialization state.

Fixes: 38caee9d ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.

This patch fixes it by checking if crq is not empty before reading the
message.

Fixes: c1a81619 ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: NXi Wang <wangxi11@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HCLGE_PROMISC_TX_EN_B and HCLGE_PROMISC_RX_EN_B are not supported
on pdev revision(0x20), new revision(0x21) supports them.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.

This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Reviewed-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vf module is loading, the cmd queue initialization should
happen before misc interrupt initialization, otherwise the misc
interrupt handle will cause using uninitialized cmd queue problem.
There is also the same issue when vf module is unloading.

This patch fixes it by adjusting the location of some function.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_ARM_SMMU_V3 is enabled, arm64's dma_ops will replace
arm64_swiotlb_dma_ops with iommu_dma_ops. When releasing contiguous
dma memory, the new ops will call the vunmap function which cannot
be run in interrupt context.

Currently, spin_lock_bh is called before vunmap is executed. This
disables BH and causes the interrupt context to be detected to
generate a kernel panic like below:

[ 2831.573400] kernel BUG at mm/vmalloc.c:1621!
[ 2831.577659] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 2831.699907] Process rmmod (pid: 1893, stack limit = 0x0000000055103ee2)
[ 2831.706507] Call trace:
[ 2831.708941]  vunmap+0x48/0x50
[ 2831.711897]  dma_common_free_remap+0x78/0x88
[ 2831.716155]  __iommu_free_attrs+0xa8/0x1c0
[ 2831.720255]  hclge_free_cmd_desc+0xc8/0x118 [hclge]
[ 2831.725128]  hclge_destroy_cmd_queue+0x34/0x68 [hclge]
[ 2831.730261]  hclge_uninit_ae_dev+0x90/0x100 [hclge]
[ 2831.735127]  hnae3_unregister_ae_dev+0xb0/0x868 [hnae3]
[ 2831.740345]  hns3_remove+0x3c/0x90 [hns3]
[ 2831.744344]  pci_device_remove+0x48/0x108
[ 2831.748342]  device_release_driver_internal+0x164/0x200
[ 2831.753553]  driver_detach+0x4c/0x88
[ 2831.757116]  bus_remove_driver+0x60/0xc0
[ 2831.761026]  driver_unregister+0x34/0x60
[ 2831.764935]  pci_unregister_driver+0x30/0xb0
[ 2831.769197]  hns3_exit_module+0x10/0x978 [hns3]
[ 2831.773715]  SyS_delete_module+0x1f8/0x248
[ 2831.777799]  el0_svc_naked+0x30/0x34

This patch fixes it by using spin_lock instead of spin_lock_bh.

Fixes: 68c0a5c7 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: NXi Wang <wangxi11@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.

This patch fixes it by updating the link state in ae_stop function.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does bit of a clean-up by using already defined enums for
certain values in function hclge_is_special_opcode(). Below enums from
have been used as replacements for magic values:

enum hclge_opcode_type{
	<snip>
	HCLGE_OPC_STATS_64_BIT		= 0x0030,
	HCLGE_OPC_STATS_32_BIT		= 0x0031,
	HCLGE_OPC_STATS_MAC		= 0x0032,
	<snip>
};
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:

[   20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[   20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[   20.022100] Error: Driver 'hns3' is already registered, aborting...
[   23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[   23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[   23.698270] Call trace:
[   23.700705]  __list_del_entry_valid+0x2c/0xd8
[   23.705049]  hnae3_unregister_client+0x68/0xa8
[   23.709487]  hns3_init_module+0x98/0x1000 [hns3]
[   23.714093]  do_one_initcall+0x5c/0x170
[   23.717918]  do_init_module+0x64/0x1f4
[   23.721654]  load_module+0x1d14/0x24b0
[   23.725390]  SyS_init_module+0x158/0x208
[   23.729300]  el0_svc_naked+0x30/0x34

This patch fixes it by adding module version info.

Fixes: 38caee9d ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: NXi Wang <wangxi11@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the missing initialization of the client list node
in the hnae3_register_client() function.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NXi Wang <wangxi11@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removes the goto and directly returns in case of errors as part of the
cleanup.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the RX leg driver needs to fetch the ethernet header
length from the RX'ed Buffer Descriptor. Currently, proprietary
version hns3_nic_get_headlen is being used to fetch the header
length which uses l234info present in the Buffer Descriptor
which might not be valid for the first Buffer Descriptor if the
packet is spanning across multiple descriptors.
Kernel default eth_get_headlen API does the job correctly.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Reviewed-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the error reported by Intel's kbuild and fixes a
return value in one of the legs, caught during review of the original
patch sent by kbuild.

Fixes: fdb793670a00 ("net: hns3: Add support of .sriov_configure in HNS3 driver")
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We call pcim_iomap in hclge_pci_init, pcim_iounmap should be called
in error handle of hclge_init_ae_dev.

We call pcim_iomap in hclge_pci_init, but do not call pcim_iounmap in
hclge_pci_uninit. When we remove the hclge.ko and insert it again, a
problem that pci can not map will happen. pcim_iounmap need to be called
in hclge_pci_uninit.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As HNS3 driver will enable SRIOV default and enable all VFs the
HW support, if PF and VF driver compiled to kernel, VF driver
will work on host default, it is not right.

This patch adds support for hns3_driver.sriov_configure to support
user configs the VF_num, and do not enable sriov default.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Suggested-by: NZhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hclge_ae_start is called, hdev->hw.mac.link may be set
to one after up/down multi-times, which does not correspond to
the link state of netdev when the netdev is up.

This fixes it by setting hdev->hw.mac.link to zero when
hclge_ae_start is called.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sriov is enabled, the Qset and tc mapping is not longer one
to one relation.

This patch fixes it by mapping all pf and vf's Qset to tc.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A client includes many client instance. Just like ae_algo, Initializing
client instance failed does not represent registering client failed.
The action of registering client just is adding client to the client
list and the result always is true. This patch changes the return
value of hnae3_register_client form a variable value to a fixed value,
makes the function always return ok.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ae_algo is used by many ae_devs. It is not only belong to just a
ae_dev. Initializing ae_dev failed does not represent registering ae_algo
failed. Because the action of registering ae_algo just is adding ae_algo
to the ae_algo list and it is always is true, it make no sense to define
return type as int.

This patch changes the return type of hnae3_register_ae_algo from int to
void.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If hclge.ko has not been inserted, the value of ret always is zero
in hnae3_register_ae_dev. If hclge.ko has been inserted, the value
of ret is zero or non zero. Different execution ways have different
results. It is confusing.

The ae_dev which is initialized failed can be reinitialized when we
remove hclge.ko and insert it again. For the case initializing client
instance, it is just like the case initializing ae_dev. The main function
of hnae3_register_ae_dev is adding the ae_dev to ad_dev list. Because
adding ae_dev is always ok, we does not need to return any in this
function.

This patch changes the return type of hnae3_register_ae_dev from int
to void.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the client instance is initializd failed, we do not need to uninit it.
This patch adds a state check to check init state of client instance.

Fixes: 38caee9d ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When initializing ae_dev failed during loading hclge.ko, the drvdata will
be set to null. When removing hns3.ko, we get a null ae_dev. It causes the
null pointer problem.

This patch removes pci_set_drvdata from error handle of hclge_init_ae_dev
to fix the bug, since pci_set_drvdata has been called in hns3_remove.
Also, we do not need to uninit the ae_dev which is not initialized. And
it may be the one which is initialized failed.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hnae3_unregister_ae_algo is called by PF, pci_disable_sriov is
called. And then, hns3_remove is called by VF. We get deadlocked in
this case.

Since VF pci device is dependent on PF pci device, When PF pci device
is removed, VF pci device must be removed. Also, To solve the deadlock
problem, VF pci device should be removed before PF pci device is removed.

This patch moves pci_enable/disable_sriov from hclge to hns3 to solve
the deadlock problem.

Also, we do not need to return EPROBE_DEFER in hnae3_register_ae_dev,
because SRIOV is no longer enabled in the context calling
hnae3_register_ae_dev. Mutex_trylock can be replaced with mutex_lock.

Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refactors the loopback related function in order
to support the serdes loopback.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The head or tail in hardware is not longer valid when resetting,
current hns3_clear_all_ring use them to clean the ring, which
will cause problem during resetting.

This patch fixes it by using next_to_use and next_to_clean in
the ring struct.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>