Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.

Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>

Both IRQ and GPIO controllers can now be represented in DT.  The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

The two device tree files octeon_3xxx.dts and octeon_68xx.dts are
trimmed by code in a subsequent patch to reflect the hardware actually
present on the board.  To this end several properties that are not
part of the declared bindings are added to aid in trimming off
unwanted nodes.  Since the device tree and the code that trims it are
bound into the kernel binary, these 'marker' properties never escape
into the wild, and are purely an implementation detail of the kernel
early boot process.  This is done for backwards compatibility with
existing boards (identified by a board type enumeration value by their
bootloaders).  New boards will always pass a device tree from the
bootloader, the built-in trees are ignored in this case.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3937/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Some mxc processors have an edge_sel feature, which allows the IRQ to be
triggered by any edge.

This patch makes use of this feature if available, which skips mxc_flip_edge().

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: NSascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a flags field to the gpio specifier for Samsung. I didn't
want to add yet another field in the already quite long specifier, so
I decided to compress it together with the Pull Up/Down settings instead.

This is needed to, for example, have a gpio-keys input that is active low.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Any non-standard property should contain the vendor's identifier which
should be perpended onto the property name followed by a comma. This
aids in name-space collision prevention. This patch ensures the
sleepmode property adheres to the rules.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

gpio-i2c describes an I2C controller (using gpios for data and clock),
so it must be described in i2c, not gpio.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree.  Also update binding
document to make it clear.
Reported-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Trivial fix
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

The of_get_named_gpio_flags can retrieve the second cell of
gpio-specifier as the "flags".  The imx and mxs gpio driver do not
have their own .xlate callback, which means of_gpio_simple_xlate is
used and it's a 1:1 mapping between gpio controller flags and Linux
"enum of_gpio_flags".

Update imx and mxs bindings document to make it clear.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Rename all Tegra binding documentation according to the first or
primary compatible value they describe. This provides a clear naming
scheme for the files, and prevents any naming conflicts should future
SoC versions require their own binding.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Implements OF support and add code to load custom properties from the DT.

The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
peripheral controller used to drive external shift register cascades. At most
3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
to drive the 2 LSBs of the cascade automatically. Newer socs are also able to
automatically drive some pins via the internal PHYs. The driver currently only
supports output functionality. Patches for the input feature found on newer
generations of the soc will be provided in a later series.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3839/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implements OF support and convert to of_mm_gpio.

By attaching hardware latches to the External Bus Unit (EBU) on Lantiq SoC, it
is possible to create output only gpios. This driver configures a special
memory address, which when written to, outputs 16 bit to the latches.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3840/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds device tree support for gpio-lpc32xx.c.

To register the various GPIO banks as (struct) gpio_chips via the same DT
gpio-controller, we utilize the adjusted of_xlate API to manipulate the
actually used struct gpio_chip.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

It adds device tree probe for gpio-mxs driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Append interrupt controller and timer document for mmp. Updates
documents for gpio and i2c.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Now gpio-nomadik has proper bindings devices initialised by Device Tree
entries are able to use the chained GPIO IRQ lines it provides. This
patch aims to reflect that in the gpio-nmk documentation.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add required documentation for specific gpio-nomadik DT bindings.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the DT support for the I2C GPIO expander inside the twl4030.

Note: The pdata parameters still have to be properly adapted using
dedicated bindings.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

To achieve DT support, we need to populate a custom platform_data in a
private struct from DT information. To simplify code, the adapter and
algorithm are also put into the private struct.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Add OF support in Document/devicetree directory.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Adapt the GPIO driver to retrieve information from a DT file.

Allocate the irq_base dynamically and rename bank->virtual_irq_start
to bank->irq_base.
Change irq_base type to int instead of u16 to match irq_alloc_descs
output.

Add documentation for GPIO properties specific to OMAP.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)

Support for those new features are retrieved from the device tree
compatibility string.

Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.

Original idea and code by Jean-Christophe Plagniol-Villard.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The gpios property is described in Documentation/devicetree/gpio.txt, so
reference this document.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Tegra20's GPIO controller has 7 banks, and Tegra30's controller has 8
banks. Allow the number of banks to be configured at run-time by the
device tree.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.

Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.

Update tegra*.dtsi to specify the required interrupt-related properties.

Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Document the required reg and interrupts properties.
Add a complete example.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.

The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.

In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
	                add some device tree entries.]
Signed-off-by: NTorben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

As gpio chips get registered, a device tree node which represents the
gpio chip is searched and attached to it. A translate function is also
provided to convert the gpio specifier into actual platform settings
for pin function selection, pull up/down and driver strength settings.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: fixed build error]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add binding documentation for ARM's Primecell PL061 GPIO controller.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.

Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Allocate one bit in the available extra cell to indicate if the gpio
should be considered logically inverted.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch enables fetching configuration data, which is normally provided
via platform_data, from the device-tree instead.

If the device is configured from device-tree data, the platform_data struct
is not used, and button data needs to be allocated dynamically. Big part of
this patch deals with confining pdata usage to the probe function, to make
this possible.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The patch adds device tree probe support for gpio-mxc driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Allow for multiple named gpio properties
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add support for decoding gpios from the device tree
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NOlof Johansson <olof@lixom.net>

The device tree is used by more than just PowerPC.  Make the documentation
directory available to all.

v2: reorganized files while moving to create arch and driver specific
    directories.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>