When the new_id entry in /sysfs is used for a foreign USB device, rtlwifi
BUGS with a NULL pointer dereference because the per-driver configuration
data is not available. The probe function has been restructured as
suggested by Ben Hutchings <bhutchings@solarflare.com>.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bcm43236 device showed having an issue connection to an AP without
security when auth_type was set to automatic. For this particular device
a workaround is made by selecting open-system. This problem does not
occur when using wpa_supplicant as it will not use auth type automatic.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added function to obtain chip information for chip specific
code.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend the bus interface with chip identifier and revision. This
will be used when certain devices need special handling in the
driver.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify code by using single function for converting channel to
chanspec. No need to set 40MHz flags, as they are not needed for
correct working in FW.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up function, removing some unnecessary code and
initialisation.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When supporting multiple netdevs it is usefull to log idx in netdev
related functions. This will be used for features like P2P.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Statistics were tracked by bus driver while it is to be tracked
per ifp/netdev.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pending 8021x frames were tracked per dongle. This should be
done per ifp.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At netdev up the mac address from drvr is copied to netdev mac
address. This is incorrect and mac address was already set by
brcmf_net_attach by copying it from ifp.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The tracking of up/down status in bus interface is unnecessary.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The
device was tested in managed mode with no security, WEP 128
bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum:
7d676323ac60d6e1a3b6d61e8c528248). It works.
Signed-off-by: NTomasz Guszkowski <tsg@o2.pl>
Cc: <stable@vger.kernel.org>
Acked-By: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add PCI deviceIDs for single band versions of 88W8366, found e.g. in
simultaneous dual band routers based on kirkwood.
Signed-off-by: NJonas Gorski <jogo@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The use of variable packet_beacon might be uninitialized in the two files,
which is same as this patch:
https://patchwork.kernel.org/patch/2006711/Signed-off-by: NCong Ding <dinggnu@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Info coming from Sweex Windows driver and wikidevi.com
0x177f,0x0163 Sweex LW163 RT3370 1x1, int. antenna
0x177f,0x0164 Sweex LW164 RT8070 1x1, Nano dongle
0x177f,0x0165 Sweex LW165 RT3370 1x1, ext. antenna
0x177f,0x0324 Sweex LW324 RT3072 2x2  with 32Mb NOR flash, autoinstall

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If gb_len is less than 3 it would cause an integer underflow and
possibly memory corruption in nfc_llcp_parse_gb_tlv().

I removed the old test for gb_len == 0.  I also removed the test for
->remote_gb == NULL.  It's not possible for ->remote_gb to be NULL and
we have already dereferenced ->remote_gb_len so it's too late to test.

The old test return -ENODEV but my test returns -EINVAL.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Samuel says:

"This is the 2nd NFC pull request.

With this one we have a new NFC driver for Inside Secure microread and a few
pn533 fixes.
Microread is an HCI based NFC IP and the driver we're pushing supports tags
R/W, and NFC p2p. It's supported over the i2c and MEI busses."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed-up drivers/net/wireless/iwlwifi/mvm/mac80211.c to change change
IEEE80211_HW_NEED_DTIM_PERIOD to IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
as requested by Johannes Berg. -- JWL
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove unneeded bitwise OR operator on uninitialized sk_buff data
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On some peculiar worlds, microreads are found hidden behind MEIs and needs
to be accessed through the ME bus.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In wl18xx, we use a new ACX command in order to set the remote
supported rates, once we know it (ie. after association).  The wl12xx
firmware doesn't support changing the rates after the STA is started,
so we need to use all supported rates.

Commit 530abe19 (wlcore: add ACX_PEER_CAP command) broke that by using
wlvif->rate_set when starting the STA role.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add back-off settings to the wl18xx_mac_and_phy_params.  We had an
empty space where the new parameters are added, so this change doesn't
affect backwards-compatibility with older firmwares.

Update WL18XX_CONF_VERSION accordingly.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

There's no need to hide the actual error that was reported when
booting fails.  For instance, on I/O error, we were returing
-EINVALID, which doesn't make sense at all.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The platform data is used not only by wlcore-based drivers, but also
by wl1251.  Move it up in the directory hierarchy to reflect this.

Additionally, make it truly optional.  At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

The platform devices can be created by both wlcore_sdio and
wlcore_spi.  Theoretically, if both are connected to the same board,
there will be a conflict.
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Just a small cleanup to use the pointer provided by wlcore_pdev_data
instead of using a separate pointer then copying.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We can't pass pointers from the platform data to the modules, because
with DT it cannot be done.  Those pointers are not set by the board
files anyway.  It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.

Create a new structure that the bus modules pass to wlcore.  This
structure contains the if_ops pointers and a pointer to the actual
platform data.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

There is no platform-specific set_power method anymore.  Power setting
is done in the bus modules (wlcore_sdio and wlcore_spi).
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.

Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version.  Fix this by using the
single-role version for everything except multi-role.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods

Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.

Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.

Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.

Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).

Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.

Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.

Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: NMarco Porsch <marco@cozybit.com>
Signed-off-by: NIvan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: NMike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add inline wrappers for the BSS struct krefs
to be able to extend them easily later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This local variable is only used once, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of annotating with a comment, add a lockdep
annotation which also serves as documentation.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the driver determined the connection was lost or that
it couldn't securely maintain the connection when coming
out of WoWLAN, send a deauth frame to the AP to also let
it know.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we had a connection for WoWLAN and after resume it
needed to be disconnected, the previous commit enabled
sending a deauth frame to the AP. This frame would not
go through on MFP-enabled networks as the key for it is
marked tainted before the frame is transmitted.

Allow a tainted key to be used for deauth frames. Worst
case, we'll use a wrong key because the PTK was rekeyed
while suspended, but more likely the PTK is still fine
and the taint flag really only applies to the GTK(s).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no reason for it to require external
locking, move it into the function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The comment about allocating the IEs together with
the BSS struct is no longer true, remove it. Also
fix a typo in the same area.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>