Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.

Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add RTC entry for dm816x.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.

The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add dma channel information to the gpmc. Although not enabled by
default this will allow prefetch-dma to be used.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the missing SPI controller DMA handler in the dm816x DT
node, only properties for the two channels on four were present.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing #mbox-cells for dm816x mbox DT node.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add dm816x DT entries for omap4-hwspinlock support as hwmod spinbox.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove invalid l3_main hwmod entry from dm816x DT ocp node.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds ti,timer-pwm property to timers 4 to 7 to permit usage of their
PWM output fonctionnality via the dmtimer driver.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The interconnects on dm816x are like on omap4, so we should use
l3-noc instead of l3-smx. But as the related SoC specific
l3_target_data is still missing from omap_l3_noc let's just
remove the entry for now.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reported-by: NMatthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With commit 3e457371 ("usb: musb: Fix fifo reads for dm816x with
musb_dsps") we need to use the right compatible flag to avoid issues
with FIFO reads.

Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Fixes: 3e457371 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like we have cppi41 on dm816x just like on am335x.

Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 7800064b ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.

This turned out several issues that need to be fixed:

- I set the GPIO type wrong to be compatible with omap3 instead
  of omap4. The GPIO controller on dm816x has EOI interrupt
  register like omap4 and am335x.

- I got the GPIO interrupt numbers wrong as each bank has two
  and we only use one. They need to be set up the same way as
  on am335x.

- The gpio banks are missing interrupt controller related
  properties.

With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.

For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 7800064b ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the USB completely because of an unconfigured USB phy, and
I only tested it to make sure the Mentor chips are detected and
clocked without a phy.

After testing the USB with actual devices I noticed a few issues
that should be fixed to avoid confusion:

- The USB id pin on dm8168-evm is hardwired and can be changed
  only by software. As there are two USB-A type connectors, let's
  start both in host mode instead of otg.

- The Mentor core is configured in such a way on dm8168-evm that
  it's not capable of multipoint at least on revision c board
  that I have.

- We need ranges for the syscon to properly set up the phy as
  children of the SCM syscon area.

- Let's not disable the second interface, the board specific
  dts files can do that if really needed. Most boards should
  just keep it enabled to ensure the device is idled properly.

Note that also a phy and several musb fixes are still needed to
make the USB to work properly in addition to this fix.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like I only got half done with moving pinctrl and syscon to
be children of the SCM. I've set up the FAPLL clocks that way already,
but did not complete the job as I copied the syscon values from
am33xx.dtsi.

To make sure the syscon mapping works, I've verfified that we can
set up davinci_emac mac address the same way as cpsw already does
with the syscon mapping. So let's add that too.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Similar to other omap variants, let's add dm816x support.

Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:

http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html

I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>