- 27 4月, 2014 2 次提交
-
-
由 Thomas Petazzoni 提交于
This commit converts the LaCie d2 Network platform to the Device Tree. All devices except LEDs are converted, because the LED code needs a non-LED GPIO to be set to a given value for the LEDs to work, and this cannot yet be easily represented in DT. Also, references to the LaCie Big Disk Network platform are lost, because this platform apparently has exactly the same hardware support as the LaCie d2 Network, so their Device Tree files would be identical. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Link: https://lkml.kernel.org/r/1398202002-28530-36-git-send-email-thomas.petazzoni@free-electrons.com Cc: Simon Guinot <sguinot@lacie.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
This commit converts the RD-88F5182 platform to the Device Tree. All devices except the PCI are converted to the Device Tree. It is worth noting that: * The PCI description for the DT case is kept in board-rd88f5182.c. * The existing non-DT support in rd88f5182-setup.c is kept as is, in order to allow testing of a given platform in both DT and non-DT cases. It will ultimately be removed, once we no longer care about non-DT support for Orion5x. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Link: https://lkml.kernel.org/r/1398202002-28530-35-git-send-email-thomas.petazzoni@free-electrons.com Cc: Ronen Shitrit <rshitrit@marvell.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 19 3月, 2014 1 次提交
-
-
由 Santosh Shilimkar 提交于
Now we have additional two SOC/boards supported, so add make file rule so that all device tree blobs can be build for keystone with 'make dtbs'. Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
-
- 15 3月, 2014 1 次提交
-
-
由 Markus Mayer 提交于
Add device tree files for the Broadcom BCM21664 SoC. Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org> Signed-off-by: NMatt Porter <mporter@linaro.org>
-
- 13 3月, 2014 5 次提交
-
-
由 Florian Vaussard 提交于
Summit is an expansion board for Gumstix Overo products. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Florian Vaussard 提交于
Chestnut43 is an expansion board for Gumstix Overo products. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Florian Vaussard 提交于
Alto35 is an expansion board for Gumstix Overo products. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Florian Vaussard 提交于
Gallop43 is an expansion board for Gumstix Overo products. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Florian Vaussard 提交于
Palo43 is an expansion board for Gumstix Overo products. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 12 3月, 2014 2 次提交
-
-
由 Jean-Jacques Hiblot 提交于
This patch implements a DTS to boot a at91sam9261ek with a dt-enabled kernel (at91_dt_defconfig). supported features are: * dbgu * lcdc * usb host * usb gadget, * spi dataflash * nand flash * touchscreen * leds * user buttons In the TODO list: * dm9000 (ethernet) * audio * mmc Signed-off-by: NJean-Jacques Hiblot <jjhiblot@traphandler.com> Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Alexandre Belloni 提交于
Add a device tree for the at91sam9rl-ek. For now it supports: - MMC - dbgu - usart1 - watchdog - nand - leds - buttons Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: NBoris BREZILLON <b.brezillon.dev@gmail.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
- 07 3月, 2014 1 次提交
-
-
由 Gregory CLEMENT 提交于
The Armada 385 RD board is the reference design board from Marvell for the Armada 385 SoC. This commit adds a Device Tree description for this board, which enables the following features: * Network interfaces * I2C bus * Serial port * SPI bus, with a SPI flash * PCIe interface Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 05 3月, 2014 4 次提交
-
-
由 Matt Porter 提交于
The BCM11351 BRT board will never see the light of day. Remove the BRT dts since it is not maintainable. Reviewed-by: NAlex Elder <elder@linaro.org> Reviewed-by: NChristian Daudt <bcm@fixthebug.org> Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org> Signed-off-by: NMatt Porter <mporter@linaro.org>
-
由 Florian Vaussard 提交于
Gumstix DuoVero is an OMAP4430-based Computer On Module. Parlor is one of the available expansion board. Tested features: - GPMC ethernet - HSUSB2 and OTG - Audio out - WiFi and Bluetooth (w2cbw0015 SDIO module) - LED and button Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 David Lanzendörfer 提交于
This patch adds basic support for the INet-97F_Rev_02 board found in various low cost consumer tablet devices (http://linux-sunxi.org/INet-97F_Rev_02) Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch> Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
This add support for the A10-OLinuXino-LIME: https://www.olimex.com/Products/OLinuXino/A10/A10-OLinuXino-LIME A low cost Allwinner A10 based dev-board, with sata, ethernet, hdmi and 2x USB. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 04 3月, 2014 3 次提交
-
-
由 Sebastian Hesselbarth 提交于
With all the DT support preparation done, we are able to move Dove to MVEBU easily. Legacy non-DT mach-dove is left untouched to rot for a while before removal. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Describe the T5325 using device tree properties, where possible. The first version of this file was produced by Thomas Petazzoni. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jason Cooper 提交于
With kirkwood migrating into mach-mvebu, mvebu_v5_defconfig needs to select ARCH_MVEBU. Unfortunately, this means that when building a v5 kernel, we unnecessarily build dtbs for the armada v7 boards. To fix this, we instead select based on MACH_ARMADA_* on a per SoC basis. Reported-by: NKevin Hilman <khilman@linaro.org> Acked-by: NKevin Hilman <khilman@linaro.org> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 03 3月, 2014 2 次提交
-
-
由 Lokesh Vutla 提交于
AM437x GP EVM DTS with pinmux information to make I2C on EVM usable. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NSourav Poddar <sourav.poddar@ti.com> Signed-off-by: NAfzal Mohammed <afzal@ti.com> Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>
-
由 Nishanth Menon 提交于
Craneboard is a hardware development platform based on the Sitara AM3517 ARM Cortex - A8 microprocessor device - see [1] for more details. Add basic devices for craneboard as replacement for the board file scheduled for removal as part of device tree conversion [1] http://craneboard.orgSigned-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>
-
- 01 3月, 2014 3 次提交
-
-
由 Christoph Fritz 提交于
INCOstartec LILLY-DBB056 is a carrier board (baseboard) for computer-on-module LILLY-A83X. This patch adds device-tree support for most of its features. Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Dmitry Lifshitz 提交于
Add support for CM-T3517 CoM and SBC-T3517 board. reused common support for sbc-t3x boards (omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi): * SB-T35 baseboard eth * MMC1, UART3 * HS USB Port 1/2 * I2C1/3 * Heartbit led Added basic support for: * MMC1 wp/cd signals * CM-T3517 Usb Hub * WL12xx WiFi chip * Davinci EMAC * AM35X OTG Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Dmitry Lifshitz 提交于
Add support for CM-T3530 CoM and SBC-T3530 board. Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 26 2月, 2014 1 次提交
-
-
由 Jason Cooper 提交于
To prevent problems later with mvebu_v5_defconfig builds, we restrict the scope of the changes this series makes. Selecting ARCH_KIRKWOOD and MACH_KIRKWOOD is necessary during the migration from mach-kirkwood to mach-mvebu. Until the last four legacy kirkwood board files have a DT equivalent, we need to support building DT from both mach-kirkwood and mach-mvebu. Reported-by: NKevin Hilman <khilman@linaro.org> Acked-by: NKevin Hilman <khilman@linaro.org> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 23 2月, 2014 1 次提交
-
-
由 Andrew Lunn 提交于
Move the kirkwood DT support into mach-mvebu, and make them part of ARCH_MULTI_V5. Minimal changes have been made in order to make it boot. Cleanup of the header files and integration with mvebu will take place in following patches. In order to help Debian transition between mach-kirkwood and mach-mvebu, the DTS files are compiled for both, allowing Debian to continue using mach-kirkwood until all remaining boards are supported by mach-mvebu. Debian is then expected to simply swap from mach-kirkwood to mach-mvebu and mach-kirkwood will be removed. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Acked-by: NArnd Bergmann <arnd@arndb.de> Tested-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 22 2月, 2014 1 次提交
-
-
由 Ben Peddell 提交于
Add device tree fragments and files to support many of the kirkwood based Synology NAS devices. This is a modification of Andrew Lunn's <andrew@lunn.ch> translation of the board setup file maintained by Ben Peddell <klightspeed@killerwolves.net> The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units. All other Synology Kirkwood-based DiskStations and RackStations use the Seiko S35390A RTC. Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed with the built-in SATA interface activity/presence pins on mpp 20-23, while the 4-bay units use ge01 and a PCIe SATA controller, and put the software controlled HDD leds on mpp 36-43. Most of the 6281 units with HDD power controls use mpp 29 and 31, while most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45 and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and most 4-bay units didn't have a separate power control for HDD1. These power controls are presumably to limit startup current from the 12V brick power supply. Instead of using separate dtsi files in a synology directory, this patch uses a single dtsi file containing all of the modules for these boards, with all of the modules not common to all boards disabled. The board dts files then enable the appropriate modules for their boards. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NBen Peddell <klightspeed@killerwolves.net> Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j) Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 20 2月, 2014 1 次提交
-
-
由 Jason Cooper 提交于
Unlike other build products in the Linux kernel, there is no 'make *install' mechanism to put devicetree blobs in a standard place. This commit adds a new 'dtbs_install' make target which copies all of the dtbs into the INSTALL_DTBS_PATH directory. INSTALL_DTBS_PATH can be set before calling make to change the default install directory. If not set then it defaults to: $INSTALL_PATH/dtbs/$KERNELRELEASE. This is done to keep dtbs from different kernel versions separate until things have settled down. Once the dtbs are stable, and not so strongly linked to the kernel version, the devicetree files will most likely move to their own repo. Users will need to upgrade install scripts at that time. v7: (reworked by Grant Likely) - Moved rules from arch/arm/Makefile to arch/arm/boot/dts/Makefile so that each dtb install could have a separate target and be reported as part of the make output. - Fixed dependency problem to ensure $KERNELRELEASE is calculated before attempting to install - Removed option to call external script. Copying the files should be sufficient and a build system can post-process the install directory. Despite the fact an external script is used for installing the kernel, I don't think that is a pattern that should be encouraged. I would rather see buildroot type tools post process the install directory to rename or move dtb files after installing to a staging directory. - Plus it is easy to add a hook after the fact without blocking the rest of this feature. - Move the helper targets into scripts/Makefile.lib with the rest of the common dtb rules Signed-off-by: NJason Cooper <jason@lakedaemon.net> Signed-off-by: NGrant Likely <grant.likely@linaro.org> Cc: Michal Marek <mmarek@suse.cz> Cc: Russell King <linux@arm.linux.org.uk> Cc: Rob Herring <robh+dt@kernel.org>
-
- 19 2月, 2014 1 次提交
-
-
由 Hauke Mehrtens 提交于
This uses the newly added BCM5301X SoC code. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Acked-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NChristian Daudt <bcm@fixthebug.org> Signed-off-by: NMatt Porter <mporter@linaro.org>
-
- 18 2月, 2014 2 次提交
-
-
由 Thomas Petazzoni 提交于
The Armada 385 DB board is the development board from Marvell for the Armada 385 SoC. This commit adds a Device Tree description for this board, which enables the following features: * Network interfaces * I2C buses * SDIO * Serial port * SPI bus, with a SPI flash * PCIe interfaces Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
The Armada 375 DB board is the development board from Marvell for the Armada 375 SoC. This commit adds a Device Tree description for this board, which enables the following features: * I2C buses * SDIO * Serial port * SPI bus, with a SPI flash. Note that the SPI bus is disabled by default, because it conflicts with the NAND, and can only work if the board boots out of SPI. Since most boards are shipped to boot out of NAND, we're default to having the SPI bus disabled. * PCIe interfaces Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 17 2月, 2014 2 次提交
-
-
由 Andrew Lunn 提交于
Perform a mechanical translation of rd88f6281-setup.c into DT. Since the hardware differs between the A0 and A1 stepping, two dts files are used, and a .dtsi file for the common parts. The A0 part does not have a "wan" port on the switch and uses PHY address 10 to address the switch. The A1 part does have the "wan" port and uses address 0. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Mechanically translate rd88f6192-nas-setup.c into DT equivelent. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 14 2月, 2014 1 次提交
-
-
由 Florian Vaussard 提交于
Unfortunatly the device tree for older OMAP35xx Overo cannot be used with newer OMAP36xx and vice-versa. To address this issue, move most of the Tobi DTS to a common include file, and create model-specific Tobi DTS. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Tested-by: NKevin Hilman <khilman@linaro.org> Acked-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 13 2月, 2014 1 次提交
-
-
由 Alexander Shiyan 提交于
PCA-100 module cannot be used standalone. This patch renames module file to .dtsi and excludes it from compilation. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 10 2月, 2014 2 次提交
-
-
由 Sascha Hauer 提交于
Add support for the GK802 'QUAD CORE Mini PC', which seems to be loosely based on the Freescale i.MX6Q HDMI dongle reference design. It is supposedly identical to the Hiapad Hi802. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Sascha Hauer 提交于
The DFI FS700-M60 is a q7 board with i.MX6 quad, dual, duallite or solo SoC. This adds support for it. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 09 2月, 2014 3 次提交
-
-
由 Lothar Waßmann 提交于
This patch adds support for the Ka-Ro electronics GmbH TX53 modules. There are two distinct module types. One with an LVDS display interface and SATA support, the other with a parallel LCD interface and no SATA interface. Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Denis Carikli 提交于
The following devices/functionalities were added: * Main and secondary UARTs. * i2c and the pcf8563 device. * Ethernet. * NAND. * The BP1 button. * The LED. * Watchdog * SD. Cc: Eric Bénard <eric@eukrea.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: NDenis Carikli <denis@eukrea.com> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Steffen Trumtrar 提交于
The "Start-R QSB" has a different PMIC than the older "Start QSB". Add a new devicetree for the Start-R. They both could use the same DT, as both PMICs (the dialog and the mc34708) have different i2c addresses and could coexist in the same DT without any errors. But once phandles are used, this will get messy. The pmic nodes are based on an earlier patch [PATCH] arm: imx53-qsb: Add Ripley driver DT nodes from Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org> which apparently got lost/abandoned. I added phandles/newlines and changed the node name from ripley to mc34708. Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-