cnic_service_bnx2x() irq handler can be called during chip reset from
MTU change.  Need to check that the cnic's device state is up before
handling the irq.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And update copyright to 2010.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only need to assign the status block address once and it also saves
space in the structure.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEddie Wai <waie@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a separate IP address for iSCSI, connections should proceed
whether or not we can get a route to the target from the network stack.
It is possible that the network IP address may not reach the iSCSI target.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEddie Wai <waie@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some data structures are freed when the device is down and it will
crash if an ISCSI netlink message is received.  Add RCU protection
to prevent this.  In the shutdown path, ulp_ops[CNIC_ULP_L4] is
assigned NULL and rcu_synchronized before freeing the data
structures.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For bnx2 devices, always send notification to bnx2i to let it initiate
the cleanup when RST is received.

For bnx2x devices, add unsolicited RST_COMP handling to start the cleanup.
Signed-off-by: NEddie Wai <waie@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize IP ID and handle some additional connection errors.
Signed-off-by: NEddie Wai <waie@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Remove periods from formats
Coalesce long formats
Use __func__
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prevent stale indices from causing spurious events when restarting the
bnx2x devices.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This step is necessary on the bnx2x devices when restarting the iSCSI
ring.  Without it, the firmware can assert and cause bnx2x to report
errors.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace pci_alloc_consistent() with dma_alloc_coherent() so that
appropriate GFP flags can be used.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The old code mistakenly zeroed out the upper 32-bit of the DMA address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix code to read the proper iSCSI MAC address for bnx2x devices.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to send a HALT command to the firmware to fully shutdown the bnx2x
rings.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old code was initializing the ring producers using an incorrect I/O
address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changed function pointer use from non-majority address-of style
to majority short form without & via: (was: 8 with &, 36 without)

grep -rPl "\btasklet_init\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
	perl -i -e 'local $/; while (<>) { s@(\btasklet_init\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done

Compile tested allyesconfig x86
Signed-off-by: NJoe Perches <joe@perches.com>

 drivers/net/cnic.c |    4 ++--
 drivers/net/jme.c  |   10 +++++-----
 drivers/net/skge.c |    2 +-
 3 files changed, 8 insertions(+), 8 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

`ulp_type' is signed, make sure it is not negative
when we read the array element.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:

commit 078b0735
bnx2: Update firmware to 5.0.0.j3.

Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/cnic.c: In function 'cnic_init_storm_conn_bufs':
drivers/net/cnic.c:1757: error: implicit declaration of function 'csum_ipv6_magic'
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add iSCSI support for bnx2x devices.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NShmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add hardware and software structures for bnx2x devices.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor ring init. code for subsequent 10G patches.  Also add rtnl_lock()
in cnic_uio_open() to prevent race condition with netdev events.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the problem of not handling the NETDEV_UP event properly
during hot-plug or modprobe of bnx2 after cnic.  The handling was
skipped by mistakenly using "else if" to check for the event.

Also update version to 2.0.1.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The iSCSI ring should be shutdown during uio_close instead of uio_open
for proper operations.  This fixes the problem of the ring getting
stuck intermittently.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The slow path ulp_init and ulp_exit calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock.  Fix it by using mutex and refcount during these
calls.  cnic_unregister_driver() will now wait for the refcount
to go to zero before completing the call.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The slow path ulp_start and ulp_stop calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock.  Fix it by using mutex and setting a bit during
these calls.  cnic_unregister_device() will now wait for the bit
to clear before completing the call.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register and unregister with bnx2 during NETDEV_UP and NETDEV_DOWN
events.  This simplifies the sequence of events and allows locking
fixes in the next patch.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the cnic driver tries to grab a symbol from bnx2 when bnx2 is
running init code, symbol_get() will succeed but symbol_put_addr()
will hit BUG() a moment later.  module_text_address() fails because
bnx2 is still in init code.

This is fixed by using symbol_put() instead which does the exact
opposite of symbol_get().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a net device goes down or when the bnx2i driver is unloaded,
the code was not generating the ISCSI_KEVENT_IF_DOWN message
properly and this could cause the userspace driver to crash.

This is fixed by sending the message properly in the shutdown path.
cnic_uio_stop() is also added to send the message when bnx2i is
unregistering.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ingo molnar <mingo@elte.hu> reported the error

drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’

when CONFIG_MODULES is not defined.  Fix by using symbol_get() instead.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This reverts commit bc3bf8fd.

All the commit did was add a second #include of <linux/module.h> which is
the wrong fix.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
 drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
 drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
 make[1]: *** [drivers/net/cnic.o] Error 1
 make: *** [drivers/net/cnic.o] Error 2

Caused by not including linux/module.h
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Fix cnic build for case of CONFIG_INET=n.
Fix cnic build for case of CONFIG_IPV6=m and CONFIG_CNIC=y.

Fixes these build errors:

cnic.c:(.text+0x236a1d): undefined reference to `ip_route_output_key'
cnic.c:(.text+0x15a8e8): undefined reference to `ip6_route_output'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The CNIC driver controls BNX2 hardware rings and resources used by
iSCSI.  Most hardware resources for iSCSI are separate from those
used for ethernet networking.

iSCSI uses a separate MAC address and IP address.  The CNIC driver
creates a UIO interface to handle the non-offloaded packets such as
ARP, etc in userspace.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>