Move the selection of the pinctrl driver to SoC family level since we
have two pinctrl drivers. It is useless to select one which is not
compatible with the SoC.

[abelloni: fixed pm.c when only sama2d2 is selected]
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add a new type of clocks that can be provided to a peripheral.
In addition to the peripheral clock, this new clock that can use several
input clocks as parents can generate divided rates.
This would allow a peripheral to have finer grained clocks for generating
a baud rate, clocking an asynchronous part or having more
options in frequency.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
[sboyd@codeaurora.org: Transition to new clk_hw provider APIs]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Add Kconfig entries, header file changes and addition to the documentation.
The early debug infrastructure is also added for easy development.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

When building a legacy (non-multi) platforms and if the ARCH_AT91 config option
is enabled there is a build error. We need AT91 to depend on multi-platform
core type options.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Drop AT91_TIMER_HZ as this can be handled using HZ_FIXED. Initial help message
was:

On AT91rm9200 chips where you're using a system clock derived
from the 32768 Hz hardware clock, this tick rate should divide
it exactly: use a power-of-two value, such as 128 or 256, to
reduce timing errors caused by rounding.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Switch AT91 to multiplatform as all SoCs are properly handled.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Import at91rm9200_time.c from mach-at91 as timer-atmel-st.c. Further cleanup is
required to get rid of the mach-at91 headers.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The mach/io.h header on at91 is used to support a nonstandard I/O space
window for the cf card driver. This changes the driver to use pci_ioremap_io
in order to have the standard location, and then removes the custom
mach/io.h.

[alexandre.belloni@free-electrons.com: Added PCI dependency]
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The slow clock always exists, selecting CONFIG_AT91_SLOW_CLOCK config
is unnecessary for the suspend to memory mode.
For this mode the master clock should always switch to the slow clock.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

To simply the PM config the CONFIG_AT91_SLOW_CLOCK option will be removed,
so move "select SRAM" from under AT91_SLOW_CLOCK, add "select SRAM if PM"
under SOC_AT91SAM9 and SOC_SAMA5
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Commit 2b0ba96c ("net: phy: micrel: disable NAND-tree for KSZ8021,
KSZ8031, KSZ8051, KSZ8081") automated the NAND-tree mode deactivation
process, thus making this phy fixup useless.
Remove it along with the associated headers inclusion.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: remove selection of PHYLIB in at91 Kconfig]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Commit 20e783e3 ("ARM: 8296/1: cache-l2x0: clean up aurora cache
handling") removed the only user of the Kconfig symbol CACHE_PL310.
Setting CACHE_PL310 is now pointless. Remove its Kconfig entry, and one
select of this symbol.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Only use SOC_AT91SAM9 for all the at91sam9 SoCs. It removes all the empty
at91sam9xxx.c SoC files. It also removes the useless at91_init_soc affectation
procedure and its "init" function pointer.
Only the SoC detection and display are kept for the at91sam9:
at91_soc_is_enabled() and at91_boot_soc.map_io() function calls are also
removed.

It enables HAVE_AT91_SMD and HAVE_AT91_UTMI for all the sam9 SoCs but this only
represents 96 bytes of uncompressed kernel code.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: different organization of the patches]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

In order to remove SOC_SAM9xxx options, stop using HAVE_AT91_DBGUx.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Now that the SRAM is part of a genpool, use it to allocate memory to use for the
slowclock implementation.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Now that at91sam9 SoCs are only supported through DT, remove
CONFIG_MACH_AT91SAM9_DT and use CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Now that rm9200 is only supported through DT, remove CONFIG_MACH_AT91RM9200_DT
and use CONFIG_SOC_AT91RM9200 instead.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

An explicit selection option is not needed for board files so now we select the
board from SoC option.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: remove option's comments; split patch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

OLD_CLK_AT91 & OLD_IRQ_AT91 were only selected by entries in Kconfig.non_dt
that are now gone. So we remove all this legacy stuff and select the proper
options in the SOC_ entries.

As USE_OF is now selected directly in arch/arm/Kconfig AT91 entry, we can
safely remove it everywhere in this file.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>

As the ARCH_AT91RM9200 is removed because being !DT, we use
the SOC_AT91RM9200 variant. This option can certainly be removed
once the ST driver is reworked a bit.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>

Second part of at91rm9200 legacy !DT removal. This is the core !DT support
removal for this Atmel SoC.
Note that from now on, the Kconfig.non_dt file and its specialized options are
completely removed.
Use the Device Tree for running this board with newer kernels.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>

CONFIG_MACH_SAMA5_DT is useless as the only way to boot on sama5 based boards is
to use device tree.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: adapt on top of cleanup branch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

As there is currently no-one to take care of this old !MMU target and as its
support in recent kernels is a bit rotten, remove this at91x40 support and the
board file associated with it (at91eb01).
There are modern ARM !MMU in Mainline now so this target is not interesting for
building tests anymore. It would be better to start from these modern ARM !MMU
platforms to reintroduce at91x40 support if needed.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Now that we don't depend on anyting in the mach-at91 directory, we can just
move the driver to where it belongs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Conflicts:
	arch/arm/mach-at91/Kconfig
	arch/arm/mach-at91/Makefile

The PIT timer driver until now had a single probe function, disregarding wether
it was probed through DT or in the old-style way. This code later on was
calling some DT function to retrieve the proper values for its base address,
interrupts and clocks.

While this was working, it was preventing the usage of CLOCKSOURCE_OF_DECLARE,
and the two different probe path were not as clearly separated as they could
be.

Rework the probe path to take this into account, and switch to
CLOCKSOURCE_OF_DECLARE.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Now that the transition is over and that we probe our reset driver in every
case, we can remove the legacy code from the machine directory.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove selection of OLD_IRQ_AT91 when selecting dt boards.
Select ATMEL_AIC_IRQ for sama5 SoCs (a kernel compiled for this SoC will
always use ATMEL_AIC_IRQ driver).
Select ATMEL_AIC_IRQ for at91rm9200 and at91sam9 SoCs only if OLD_IRQ_AT91
is not selected (which means we are compiling a pure DT kernel, without
any legacy board support).

Remove specific irq init code in all dt board files: this init procedure
is automatically handled in of_irq_init which is called by the arm irq core
code and is in charge of calling the appropriate aic init functions.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Introduce the OLD_IRQ_AT91 Kconfig option to prepare migration to the
new AIC driver.

Select this option for all at91 SoCs and all available boards so that we
can later move DT enabled boards to the new irq driver and keep the old
implementation when legacy boards are selected.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

When using device tree, select the Atmel RAM controller driver to handle its
clocks.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting
at91sam9263 SoC support. This will automatically enable COMMON_CLK_AT91
option and add support for at91 common clock implementation.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting at91sam9g45
SoC support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clock implementation.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting at91sam9260
SoCs support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clk implementation.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting at91rm9200
SoC support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clk implementation.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9n12 SoC support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

It makes no sense for sama5 support to be enabled if we don't
also enable USE_OF. Making this automatic in Kconfig avoids
a possible randconfig conflict between the old and new clock
support code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>

at91x40 is different from all the other at91 machines, and it is
impossible to build a kernel that works on both this SoC and
any of the others, even though it is possible to build a noMMU
kernel for any at91 machine.

By turning at91x40 into a separate top-level option, we explicitly
forbid enabling invalid configurations that include mutually exclusive
machines.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9261 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>