This patch adds support for DVB-Opera S1 USB 2.0 BOX.
Signed-off-by: NMarco Gittler <g.marco@freenet.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I got strange message when I did modprobe bt878:
bt878_probe: card id=[0x0],[ <NULL> ] has DVB functions.
The card_list array is terminated by sentinel entry.
But this list is traversed by:
for (i = 0, dvb_cards = card_list; i < ARRAY_SIZE(card_list);
     i++, dvb_cards++) {
...
}
in bt878_probe().
So this loop checks dummy sentinel entry, too.
This patch removes unnecessary sentinel entry.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

fixed hotplugging for dvbnet
Signed-off-by: NMichal CIJOML Semler <cijoml@volny.cz>
Signed-off-by: NMarkus Rechberger <markus.rechberger@amd.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

fixing hotplug issue for demux[n] and dvr[n]
Signed-off-by: NMichal CIJOML Semler <cijoml@volny.cz>
Signed-off-by: NMarkus Rechberger <markus.rechberger@amd.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

fixed frontend hotplug issue
Signed-off-by: NMichal CIJOML Semler <cijoml@volny.cz>
Signed-off-by: NMarkus Rechberger <markus.rechberger@amd.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If you modprobe the b2c2-flexcop-pci module you got a hardlock of your system.
This is due the usage of spin_lock before spin_lock_init is called.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It's KERN_WARNING "lgdt....", not "KERN_WARNING lgdt...."
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When the tuner is attached, the tda10046 is not initilized yet, so it
is searching for its firmware. If the tuner is attached to the tda10046
silent i2c port, a bus collision can occur. Now the version is probed
during the first init or sleep call.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for Anubis Electronics "Lifeview" (USB-ID: 0x10fd:0x1513)
Signed-off-by: NPierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The struct tda1004x_config has a new entry: .ts_mode
Possible values are TDA10046_TS_PARALLEL or TDA10046_TS_SERIAL
There always is only one interface active, default is parallel.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The dvb-pll sleep function could only send a 2-byte sequence to the PLL.
This isn't enough in some cases, for example fmd1216me will need to send
a 4-byte command to set both BB and AB to the correct values.

Instead of using a fake band with a frequency of 0 to store the sleep
data (which has room for only two bytes), the new sleep function works
like the init function.  A new pointer is added to the pll description,
and when non-NULL points to a buffer with the length and data to send.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The IF frequency was specified for each band, but it's not something that
changes from band to band.  None of the tuner definitions had a different
IF frequency (called offset) from one band to another.
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some PLLs had one half the step size added to the offset, so that the
divisor would be rounded to the nearest integer.  Some didn't and so
would always be rounded down.

This makes dvb-pll round to the nearest when calculating the divisor,
without the offset needing to be fudged.  PLLs that had a fudged offset
have the offset changed to be just the IF frequency.
The satellite PLL dvb_pll_philips_sd1878_tda8261 was rounding up for some
reason, and I've kept it that way.

In addition, frequencies that were rounded to the nearest kHz are
extended to full Hz resolution.  One sixth MHz step sizes that were
listed as 166,666 Hz are changed to 166,667 Hz, which is slightly closer.

PLLs that were already rounding:
dvb_pll_tda665x, offset was 36 1/6 (to nearest kHz) + step/2
dvb_pll_fmd1216me, offset was 36 1/8 (to two digits) + step/2
dvb_pll_thomson_fe6600, offset was 36 1/8 (to two digits) + step/2
dvb_pll_env57h1xd5, offset was 36 1/8 + step

Note that the last PLL, dvb_pll_env57h1xd5, appears to have had a bug in
the offset.  Rather than adding stepsize/2, it was adding a full
stepsize.  The PLL definition originally came from the dibusb driver,
which used 36 1/8 + step/2.  The change to 36 1/8 + step was probably a
mistake added when the tuner was converted to dvb-pll.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NPierre Willenbrock <pierre@pirsoft.dnsalias.org>
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This function should work for all m920x-based devices.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix bug introduced during infrared refactoring.
Thanks to Johann Friedrichs for spotting this.

Thanks-to: Johann Friedrichs <johann.friedrichs@web.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Change a 00 to just 0
Detect zero-length I2C messages and return not supported.  I think I know
how to send one, but the problem is getting the slave's ack.  The only
point of a zero-length message is for probing; too see if the slave will
ack its address.  Since we don't know how to get the ack, we can't
support zero-length messages in a useful way, so it's probably best to
just return not supported for them.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Write some better documentation about what might be known about how the
m920x I2C works, since a datasheet is lacking.
The I2C xfer function should now handle more types of I2C transactions
than it could before.  Those it can't, will return error codes instead of
being executed incorrectly.  Multi-byte reads were not being done
correctly, which should be fixed.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- r/w bit is not part of the i2c address
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Implement m920x i2c as suggested by Pierre Willenbrock
- remove "magic" hack
- r/w bit is not part of the i2c address
- move hardware remarks to header file
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In transfer/replay mode the frontend lock status was never updated.
This caused a 'black screen' if VDR switched from transfer mode to
live mode on the same transponder.
Thanks to Marco Schluessler for spotting the problem.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The code the i2c transactions was leftover from the old V4L-based ATSC
driver.  It did too little with too much code.  It is re-written to
remove unnecessary parameters and be more efficient.  A demod register
can now be read with one function call, instead of repeating a dozen line
block of code each time.

There were msleep()'s, which appear to be unnecessary, spread around all
the I2C transactions.  These have been removed.  Reading SNR used to take
about 130 ms, now it's down to 1.8 ms.

Reads from the demodulator's registers do not return correct results
sometimes.  Adding or removing the delays in the I2C transactions did not
appear to effect the probability of failure.  If anything, the
transactions without delays were less likely to fail, but since far more
transactions could be made per second the number of failures per hour was
greater.

To increase reliability, the SNR and get_params functions will now retry
once if they get bad data back.  This appears to have reduced the
probability of failure to effectively zero.
Some error messages are cleaned up or given KERN_* levels when they were
missing.  

or51132_setmode() wasn't returning correct error codes, which is fixed as
well.

CC: Rusty Scott <rustys@ieee.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When trying to use a Hauppauge Nova-T Stick on a big-endian architecture
(such as powerpc) no frontend can be attached.
The attached patch fixes this problem by removing two lines in
dib0700_ctrl_rd() that try to correct the endianess on two values that
already are correct:
-       /* think about swapping here */
-       value = le16_to_cpu(value);
-       index = le16_to_cpu(index);
With this simple patch this dvb hardware works great, thanks to anyone
involved for the good work. :)
Signed-off-by: NDennis Ranke <mail@exoticorn.de>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Added USB_PID_PCTV_450E to the 'usb_device_id ttusb2_table' and an entry in the
.devices table.  The 400e driver now supports the 'Pinnacle PCTV Sat Pro USB
(450e)' with USB_ID 2304:0222.
Signed-off-by: NChristophe Cattelain <xof@skynet.be>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- The i2c data buffer in tda827xa_set_params was 1 byte too short
- saa7134-dvb now gives an error mesage if tda827x could not be attached
- coding style fix in tda1004x.c
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The code of the dvb-pll driver and the lgh06xf driver is nearly
identical.  The main difference is that the lgh06xf driver would set the
AGC TOP value on every tune call.  The dvb-pll driver now has the ability
to set the AGC TOP when the front-end device is opened, which is a better
way to go about it.  By using this ability of dvb-pll, the lgh06xf driver
is made unnecessary.

There is one other difference.  dvb-pll will probe for the presence of an
I2C pll chip by doing a one byte read, the lgh06xf driver did not do
this.  In some devices the PLL is not reachable over I2C at the timer the
tuner is attached.  Some more initialization, such as firmware loading,
must take place first.  None of the devices using a LG-H06xF should have
this problem.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some tuners need or benefit from initialization, to change certain
settings from their power on default values.

Typically, tuners with TUA603x PLLs can benefit from setting the AGC TOP
value to something else.  This patch includes code to set the AGC TOP to
103 dBuV for the Thomson DTT-761x tuners, which I have experimentally
verified gives the best SNR readings, increasing SNR by about 0.19 dB
over the default value.

Other tuners can make use of this as well.  For example, the separate LG
TDVS-H06xF driver's only difference from dvb-pll is this same setting of
AGC TOP value.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A number of drivers selected DVB_PLL when they did not need it, and some
that did need it did not select it.

The DVB_PLL option is given a name and help text, so that it will show up
in the config menu.  DVB_PLL support can be turned on if an out-of-tree
driver needs it.

The standard dvb fe customization support is added to dvb-pll.h.  Since
all modules which select DVB_PLL do so unconditionally, it is not
possible to turn dvb-pll off when an enabled module selects it, unlike
most of the other frontend/tuner drivers.  This is because the users of
dvb-pll have static references to dvb-pll symbols other than the attach
function.  If these references are removed, then dvb-pll will be
disablable as the other frontend/tuner drivers are.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Better to use sizeof() to get the size of the output buffer for the tuner
name, instead of just hard coding 128.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support for MSC_RAW and MSC_SCAN remote control events.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The attached patch contains the last set of changes to the budget-ci IR
handling which makes it use the repeat handling of the input subsystem.
This allows some code simplification, makes sure that repeat key presses
are reported as such and also allows the "debounce" hack to be removed
altogether.
In addition a couple of static variables were removed which would have
confused the IR code if more than one card is used.
Signed-off-by: NDavid Hardeman <david@hardeman.nu>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Infrared remote control support rewritten.
Now each device provides its own event device, keymap, protocol,
inversion and address setting.
EVIOCGKEYCODE and EVIOCSKEYCODE ioctls are supported to read/modify
a keymap. Keymaps may be loaded using
- input tools (keyb etc.)
- av7110_loadkeys (obsolete, for backward compatibility)
New command line parameters:
- ir_protocol:    select infrared protocol: 0 RC5, 1 RCMM (default)
- ir_inversion:   signal inversion: 0 not inverted (default), 1 inverted
- ir_device_mask: bitmask of infrared devices (default: accept all)
Those parameters may be set anytime.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The parameters for minimum and maximum frequency were missing.
Also added mail addresses of the module authors.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This change sets the tda827x to sleep mode right after attach in dvb
mode. It is just to save power. For the same reason, the ADC of the
tda10046 gets turned off in sleep mode.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The patch moves the tda827x dvb tuning code to a separate module
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In older versions, this was used to decide whether to boot from
eeprom or file. This is no longer necessary but the check helps to avoid
an oops with misconfigured cards.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are the following changes:
- separate configuration of IF and GPIOs.
- set GPIOs before firmware load. This helps to avoid I2C address
  collisions.
- if desired invert GPIOs at sleep (automatic return to analog mode of card).
- added 3 tuner configuration bytes to config stuct.
- added i2c gate address to config struct.
- moved _state struct declaration to header file to make it accessible
  on board layer.
- added "conf_probed" to the state struct to allow i.e. probing for correct
  tuner version.
- changed firmware load mechanism to always:
  + check if already loaded
  + try to boot from eeprom
  + try downlad from host
- corrected name of tda10046 firmware image (backward compatible).
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The cx23415 adds some extra features that this DVB decoding API did
not support. This API has been expanded to support the required
features. Both source and binary backwards compatibility is kept
intact by these changes. So existing applications are not affected.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NRalph Metzler <rjkm@metzlerbros.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>