HWSIM_CMD_GET_RADIO returns information about a specific radio id or
all of them in response to a dump. Create the netlink skb or use the
one provided by the dump functionality. Use the existing attribute
appending function to fill in the same attributes when creating a
new hwsim radio.

Save alpha2 and struct ieee80211_regdomain in the hwsim data or else
they will be lost in the depths of regulatory infrastructure.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Factor out netlink message attribute appending in order to reuse it
with later code. As a result move netlink skb allocation to the
calling function.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The hwname will always be set if idx is negative (as it's
a u32 read into an s64 it can't overflow either) so we can
remove the unnecessary check for hwname being non-NULL.

This was reported by smatch.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We can always know the hwname of the radio so use the value
from wiphy.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds support for scanning with random MAC address for
both software and hardware scan.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, when a roc period expires, the offchannel
timer calls ieee80211_remain_on_channel_expired(), but
the roc state is cleared only when the queued work
to switch to the operating channel gets a chance to run.

This race is a problem because mac80211 can issue a
new roc request in this window. To avoid this, handle
roc completion in the offchannel timer itself.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a GO/STA setup, when we switch to the STA context,
the channel context timer is scheduled with a period of
half the beacon interval. If a beacon is received in
this duration, the timer is adjusted to accommodate
TSF sync done by the HW.

But, if the actual channel switch is delayed for some
reason, we end up rearming the timer every time a new
beacon is received. Avoid this by doing the adjustment
only once.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If for some reason a beacon with a new NoA is
not sent out, then reset the mgd_prepare_tx flag.
Not doing this will result in a situation where
a GO will send a new NoA when it shouldn't.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes sure that pending roc/scan
operations are cancelled properly when a new
context is assigned/unassigned.

The flush_work() call to flush out any scheduled
channel context work is removed, instead, sc->mutex
is dropped to allow any pending work to get a chance
to complete by the channel scheduler. Also, increase
the timeout to allow a switch to an active GO.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a pending roc or scan operation is cancelled,
the offchannel operation is cleared, but the offchannel
state in the main scheduler is not cleared. This causes
problems since an active GO will try to process a stale
offchannel request that was deferred earlier. Fix this
by clearing the state when there is no pending offchannel
(roc/scan) operation.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.

Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.

The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.

Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.

Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: NMiaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.

So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.

This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n

and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds auto TDLS support to mwifiex.

Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.

So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.

Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.

Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.

To record tx ieee80211 headers

     trace-cmd record -e ath10k_tx_hdr

To record complete packets

     trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While preparing an ad-hoc start command, the capability info bitmap is
needlessly set from the command, and then the ESS bit cleared.

Change to set the bitmap directly without reference to the command.
Signed-off-by: NJames Cameron <quozl@laptop.org>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wlcore_cmd_send_failsafe() function is only called in the cmd.c
file, where it is definde.  Make it static.

Additionally, move the EXPORT_SYMBOL macro for wl1271_cmd_send() to
the right place.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check for the minimum required buffer length in wlcore_cmd_send() and
wlcore_cmd_configure_failsafe.  This ensures that we will never try to
use a buffer that is smaller than the required header.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's been observed that wrong firmware version (ex. 66.14.96.p9
instead of 14.66.9.p96) is displayed on big endian platforms.

The problem is fixed here.
Reported-by: NDaniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: NDaniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>