ARC common code to enable a SMP system + ISS provided SMP extensions.

ARC700 natively lacks SMP support, hence some of the core features are
are only enabled if SoCs have the necessary h/w pixie-dust. This
includes:
-Inter Processor Interrupts (IPI)
-Cache coherency
-load-locked/store-conditional
...

The low level exception handling would be completely broken in SMP
because we don't have hardware assisted stack switching. Thus a fair bit
of this code is repurposing the MMU_SCRATCH reg for event handler
prologues to keep them re-entrant.

Many thanks to Rajeshwar Ranga for his initial "major" contributions to
SMP Port (back in 2008), and to Noam Camus and Gilad Ben-Yossef for help
with resurrecting that in 3.2 kernel (2012).

Note that this platform code is again singleton design pattern - so
multiple SMP platforms won't build at the moment - this deficiency is
addressed in subsequent patches within this series.
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rajeshwar Ranga <rajeshwar.ranga@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>

There is a bit of hack/kludge right now where we disable preemption if a
L2 (High prio) IRQ is taken while L1 (Low prio) is active.

Need to revisit this
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>

* arc-uart platform device now populated dynamically, using
  of_platform_populate() - applies to any other device whatsoever.

* uart in turn requires incore arc-intc to be also present in DT

* A irq-domain needs to be instantiated for IRQ requests by DT probed
  device (e.g. arc-uart)

TODO: switch over to linear irq domain once all devs have been
      transitioned to DT
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>

This contains:
-bootup arch IRQ init: init_IRQ(), arc_init_IRQ()
-generic IRQ subsystem glue: arch_do_IRQ()
-basic IRQ chip setup for in-core intc
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>

ARC700 has an in-core intc which provides 2 priorities (a.k.a.) "levels"
of interrupts (per IRQ) hencforth referred to as L1/L2 interrupts.

CPU flags register STATUS32 has Interrupt Enable bits per level (E1/E2)
to globally enable (or disable) all IRQs at a level. Hence the
implementation of arch_local_irq_{save,restore,enable,disable}( )

The STATUS32 reg can be r/w only using the AUX Interface of ARC, hence
the use of LR/SR instructions. Further, E1/E2 bits in there can only be
updated using the FLAG insn.

The intc supports 32 interrupts - and per IRQ enabling is controlled by
a bit in the AUX_IENABLE register, hence the implmentation of
arch_{,un}mask_irq( ) routines.
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>