- 01 10月, 2011 8 次提交
-
-
由 Yogesh Ashok Powar 提交于
Making adding and deleting virtual interfaces dynamic. Adding handlers for creating and deleting virtual interface with given name and dev respectively. Also, creating default interface of type station on insmod of the driver. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
"iw dev mlan0 link" shows wrong data rate, because data rate is not sent properly to cfg80211 stack. Also stack is not updated with mcs and Tx data flags information. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
In disconnected state "iw dev mlan0 link" command will return from cfg80211 stack itself. We also have an error check in mwifiex_cfg80211_get_station() routine. Therefore the code under "if (!priv->media_connected)" condition in mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
An extra call to mwifiex_dump_station_info() routine in get_station callback function is redundant Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Make use of the rx status's is_mybeacon in order to avoid redundant memcmp. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Fill the ampdu_[ack]_len for both aggregation and normal frames. So that we could avoid unnecesary conditional at tx status. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lorenzo Bianconi 提交于
I noticed a possible issue in the max_tp_rate2 management of minstrel_ht. In particular, if we look up just among max_tp_rate2 of each group it will be possible that the selected rate will not be the mcs with second maximum throughput. I wrote this simple patch. Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Andy Shevchenko 提交于
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: "John W. Linville" <linville@tuxdriver.com> Tested-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 9月, 2011 32 次提交
-
-
git://git.infradead.org/users/linville/wireless由 John W. Linville 提交于
Conflicts: drivers/net/wireless/iwlwifi/iwl-scan.c net/wireless/nl80211.c
-
由 Arik Nemtsov 提交于
Correct flag usage - use it as a bit index instead of a bit value. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
wrqu->encoding.length comes from the network administrator. It's size u16. We want to limit "tocopy" to the smallest value of either "len_keys", "wrqu->encoding.length" or 100. But because .length gets cast from u16 to u8 we might use a random, smaller value than the was desired. It's probably not very serious, but we may as well fix it. Btw, this is from code auditing and not from testing. I don't know if this affects anyone in real life. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eliad Peller 提交于
save and configure tx param per sdata, rather than per hardware. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eliad Peller 提交于
tx params are currently configured per hw, although they should be configured per interface. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Whenever the scan request or tx_mgmt is requesting not to use CCK rate for managemet frames through NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should select appropriate least non-CCK rate. This could help to send P2P probes and P2P action frames at non 11b rates without diabling 11b rates globally. Cc: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Add a new nl80211 attribute to specify whether to send the management frames in CCK rate or not. As of now the wpa_supplicant is disabling CCK rate at P2P init itself. So this patch helps to send P2P probe request/probe response/action frames being sent at non CCK rate in 2GHz without disabling 11b rates. This attribute is used with NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_FRAME commands to disable CCK rate for management frame transmission. Cc: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
We returned a freed variable on some error paths when the intent was to return a NULL. Part of the reason this was missed was that the code was confusing because it had too many gotos so I removed them and simplified the flow a bit. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NLauro Ramos Venancio <lauro.venancio@openbossa.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When we cancel a scan, the completion runs only from the workqueue. This can cause the remain-on-channel scan to fail when another one was just canceled, because we're still aborting it. To fix this, run the completion inline with the lock still held before returning from iwl_scan_cancel_timeout(). Also, to avoid the scan complete work from completing a new scan prematurely, add a new STATUS_SCAN_COMPLETE bit. Reported-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Tested-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
To make the next patch easier to read, move the function up, it'll be needed earlier in this file in the next patch. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We'll need to be able to run scan complete inline, not from the workqueue, so refactor it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The return value of iwl_scan_cancel_timeout() isn't used anywhere, so let's just remove it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Only 5150 series devices report their temperature in Kelvin, and for those we already convert it to Celsius when storing into priv->temperature, so there's no way priv->temperature will ever be in Kelvin. Remove support for this. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When an AP mode interface is added with a DTIM period of two, the slot programming is wrong. Fix it by taking into account the DTIM period. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
If iwl_scan_initiate() fails for any reason, priv->scan_request and priv->scan_vif are left dangling. This can lead to a crash later when iwl_bg_scan_completed() tries to run a pending scan request. In practice, this seems to be very rare due to the STATUS_SCANNING check earlier. That check, however, is wrong -- it should allow a scan to be queued when a reset/roc scan is going on. When a normal scan is already going on, a new one can't be issued by mac80211, so that code can be removed completely. I introduced this bug when adding off-channel support in commit 266af4c7. Cc: stable@kernel.org [3.0] Reported-by: NPeng Yan <peng.yan@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
As everybody knows kcalloc checks the multiplication is safe and that we don't run into overflow. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
In the current code, the rate scaling isn't fed with statistics from the BA notifications. This is since my patch: iwlagn: reclaim the packets in transport layer Fix that. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
Add debugging to show the status of probe in scan notification to help debug probe related issues Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
Since all the queue logic has been moved to the transport layer, the sequence number is set in the transport layer. While doing that I forgot that the mac header is copied to the TB of the TX cmd in the upper layer before the call to the transport layer. So basically we used the sequence number from mac80211... This was fine for the first assocation but after the second, mac80211 resets its counters while we don't hence a shift that led to terrible impact on performance. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
Change to iwlwifi.git instead of iwlwifi-2.6.git iwlwifi-2.6.git still works for backward compatibility Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
Since priv->temperature is signed, we cannot use debugfs_create_u32 to refer to it. Use a regular debugfs file instead. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
Txid was used without being initialized. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
After 'ath9k: optimize ath9k_ps_restore', it would only send the device to network sleep and not to full sleep anymore, potentially causing more battery drain. Reported-by: NVivek Natarajan <nataraja@qca.qualcomm.com> Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ilan Elias 提交于
Protect 'cb' and 'cb_context' arguments in nci_data_exchange. In fact, this implements a queue with max length of 1 data exchange transactions in parallel. Signed-off-by: NIlan Elias <ilane@ti.com> Acked-by: NLauro Ramos Venancio <lauro.venancio@openbossa.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ilan Elias 提交于
When start_poll is called, and a target was implicitly activated, we need to implicitly deactivate it. On the other hand, when the target was activated by the user, we should not deactivate it. Signed-off-by: NIlan Elias <ilane@ti.com> Acked-by: NLauro Ramos Venancio <lauro.venancio@openbossa.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ilan Elias 提交于
Signed-off-by: NIlan Elias <ilane@ti.com> Acked-by: NLauro Ramos Venancio <lauro.venancio@openbossa.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
After handling command response, cmd skb is inserted into command free queue(which keeps track of availabile skbs) for reuse purpose. Skb length is not getting reset to zero here. This patch takes care of it. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
ieee80211_channel_to_frequency() routine expects band parameter in the form of "enum ieee80211_band band". Currently driver specific band (BAND_A, BAND_AN etc.) is passed to the routine. This patch makes sure that correct parameter is passed. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
In recent commit "mwifiex: use cfg80211 dynamic scan..." (7c6fa2a8..) scan table handling in driver is removed to make use of cfg80211 dynamic scan table. Now driver sends beacon buffers found in scanning directly to stack and parse the buffer for requested BSS only during association. Beacon buffer doesn't contain bss band information. Driver gets it from firmware in separate tlv (chan_band_tlv). Currently since we don't inform stack about bss bandinfo, there is an issue with 5GHz association. Use "priv" field of struct cfg80211_bss to store bandinfo. This fixes 5GHz association issue. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
Sometimes association in 5GHz doesn't work. Dmesg log shows "Can not find requested SSID xyz" error message. Currently while preparing scan channel list for firmware Null entries are created for disabled channels. The routine which retrieves this list ignores channels after Null entry. Hence sometimes driver doesn't scan the channel of requested AP and association fails. The issue is fixed by avoiding those NULL entries. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-