Also change escape_ssid to print_ssid to match print_mac semantics.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses comments from Dan Williams about the patch
committed as "libertas: Improvements on automatic tx power control via
SIOCSIWTXPOW."
Signed-off-by: NAnna Neal <anna@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch addresses comments from Dan Williams about the patch
committed as "libertas: Reduce the WPA key installation time."
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CC [M]  drivers/net/wireless/libertas/wext.o
drivers/net/wireless/libertas/wext.c: In function ‘lbs_get_rts’:
drivers/net/wireless/libertas/wext.c:307: warning: comparison is always
false due to limited range of data type
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WPA requires that the PTK is installed immediately after the 4-way handshake
in order to properly decrypt the subsequent incoming EAPOL-GTK frame.  If the
PTK is not enabled by the time the EAPOL-GTK frame arrives, the frame is
dropped and the supplicant does not receive the group key.

This will happen with fast Access Points that send the EAPOL-GTK frame before
the suplicant has successfully installed and enabled the PTK.  To mitigate
this situation, this patch simplifies and accelerates the SIOCSIWENCODEEXT
execution.

This patch resolves OLPC ticket 7825 (http://dev.laptop.org/ticket/7825)
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And support setting both long and short retries independently.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwconfig txpower can now be used to set tx power to fixed or auto. If set to
auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams
noted the command was no longer supported in firmware V9+.
Signed-off-by: NAnna Neal <anna@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

with fixes for v9 and later firmware too.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

and return errors for operations like join & scan that aren't possible
when the radio is turned off.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

and remove DISASSOCIATE because it's not in any of the specs and has
never been used.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And while we're at it, grab min/max TX power from the firmware and use
that to validate incoming TX power requests from WEXT.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implemented rate adaptation support via 'iwconfig rate' API.  It is now
possible to specify a bit-rate value and append 'auto'.  That will configure
rate adaptation to use all bit-rates equal or lower than than selected value.

Made lbs_cmd_802_11_rate_adapt_rateset a direct command.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is based on a patch from Shailendra Govardhan and Brian Cavagnolo.
It extends the MESH_CONFIG command to configure non-volatile parameters on
libertas devices that support them (e.g. OLPC Active Antenna).

This patch only implements the driver/firmware interface.

See http://dev.laptop.org/ticket/6823 for minimal testing results and known
issues.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was used only at one place anyway.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Besides code moving, I did the following changes:

* made some functions static
* removed some unneeded #include's
* made patch checkpatch.pl clean
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Besides code moving, I did the following changes:

* made some functions static
* removed some unneeded #include's
* made patch checkpatch.pl clean
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes many unused function parameters as well as some not-implemented
functions, e.g. CMD_802_11_GET_STATS. The silly lbs_set_cmd_ctrl_node()
function is now also gone.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* firmware for the CF card supports power saving
* the driver currenly only accept "iwconfig ethX power on|off", so
  I fixed what the range wext ioctl reports.
* initialize value/flags in lbs_get_power()
* get rid of unused parameter psmode in lbs_ps_confirm_sleep()
* some minor debug output tweaks
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now uses __lbs_cmd() to get the "log" (it's actually more a snapshot of
various counters, not a sequential log). Besides the "mechanical" convertion
the patch add the following logical changes:

* Removes the priv->logmsg variable, it was only used in one place anyway,
  also don't blindly get the counters when associating. Getting the
  counters then the user asks via WEXT for them is good enought.
* don't set wstats.discard.fragment with log.rxfrag, because the latter is
  a counter for successfully received packets, not for fragmented packets.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After my bit scan re-writing the SIOCSIWSCAN wext ioctl no longer supported
scanning for a specific SSID. However, wpa_supplicant is a possible user of
this ioctl, so here is code that add's this.

While passing, removed even more of the debugfs-based scanning. You can (and
should) the SIOCSIWSCAN to ask for scans, so there is no need for
proprietary interfaces for scanning. And, besides, the scan result couldn't
be used further, e.g. not for associating.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Always shows the firmware release.

Also converts the firmware release into something that is easily comparable.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, we go into an endless busy loop trying to enable PS mode when
the command queue is empty, dealing with the error response, and then
trying to enable PS mode again because the command queue is empty.... it
doesn't really save much power.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is weirdness here; the firmware seems to refuse to change channels
at will.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There seems to be no reason for a separate structure; move it all
into struct lbs_private.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also clean up the double setting/clearing of IW_ENCODE_DISABLED.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv

While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The transmit and receive traffic as soon as the mesh interface is
brought up.

Test case 1:  Bring up only the mesh interface and ping.  No need for
any iwconfig commands on the main interface.

$ ifconfig msh0 192.168.5.3
$ iwconfig msh0 channel X
$ ping 192.168.5.2
If ping succeeds, PASS

Test case 2:  Associate with the main interface, and turn off AP.  Mesh
interface should not lose connectivity.

$ iwconfig eth0 mode managed essid "my_ssid"
$ ifconfig msh0 192.168.5.3
$ ping 192.168.5.2
<turn off access point>
If ping continues uninterrupted, PASS

This feature requires firmware version 5.110.19.p0 or newer, available
here: http://dev.laptop.org/pub/firmware/libertas/Signed-off-by: NAshish Shukla <ashishs@marvell.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unifies the namespace of variables, functions defines
and structures. It does:

- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
  defined in libertas-local *.h files, e.g. not defines
  from net/ieee80211.h)

While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Convert array size calculations to use ARRAY_SIZE().
Signed-off-by: NAlejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix priority mistakes similar to '!x & y'
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.

Renamed those two functions to to libertas_XXX as well.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the get-nickname wireless extension actually work. Before
this patch, I could do "iwconfig eth1 nick BLAH" but "iwconfig
eth1" would have still showed "MRVL-USB8388" to me. Hey, and that
was wrong anyway, I'm on a CF card, not on USB :-)
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>