Merge branch 'gpio-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus

The patch adds a CONFIG directive required for supporting the Amstrad Delta
connected external keyboard by default.

Created and tested against linux-omap master,
commit 104a77440f05430f29f9d3f4ecb88c1536819585 dated 2010-04-27.

Works on top of PATCH v4 4/5(7), "input: serio: add support for Amstrad Delta
serial keyboard port".
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

EHCI port on UI card and LCD share two pins (GPIO 181 and 182) thus
they have to be mutually exclusive.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to tlv320aic3x codec driver require four supplies.
Implement this by connecting analogic supplies to TWL4030 VMMC2 and digital
supplies to TWL4030 VIO.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This makes possible to probe the audio codec and add another i2c2
components in the future.

Fix also indentation for the first omap_register_i2c_bus.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I believe the VMMC2 constraints must be the same than with VAUX3. Older
boards are using TWL4030 VMMC2 supply for internal MMC whereas newer are
using VAUX3 that has more limited constraints defined in this same file.

More over, the VMMC2 supply is used also for analog audio domain and the
miminum analog voltage of the TLV320AIC34 codec is 2.7 V.

To combine these two facts, the patch changes supply name to V28_A as the
newer boards register VMMC2_30 for VAUX3 and uses the same constraints than
VAUX3 since those constraints are ok for the TLV320AIC34.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some Overo add-on boards include a second ethernet port.  This patch
adds support for that second port.
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update the default configuration for AM3517EVM to enable
support for EMAC peripheral.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.

Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Modified AM35xx EVM init sequence to handle EMAC
initialization.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define offsets for EMAC sub modules.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Modify the default kernel configuration on AM3517 to enable CAN.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board specific hookup for TI HECC driver on
AM3517 EVM
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the new default configuration for the Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize multiplexed pins with correct mode.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize isp1301 FS USB transceiver and
add I2C bus1 initialization code for OMAP2430 SDP
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The patch provides the following ams_delta_defconfig updates:
- explicitly select preemptable RCU,
- replace outdated CONFIG_LBD and CONFIG_LSF options with CONFIG_LBDAF,
- activate support for LCD contrast setting (new in 2.6.34),
- turn off verbose bug reporting for smaller kernel.

Created and tested against linux-2.6.34-rc3.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The generic gpiolib provides a debugfs interface to GPIOs which
provides identical (but nicer looking) data as the OMAP specific one.

This patch completely drops the OMAP specific interface
(/debug/omap_gpio) in favor of using the generic one (/debug/gpio.)
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

setwkuena and setdataout are covered already by wake_en and dataout fields.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Ensure GPIO debounce clocks are disabled when idle.  Otherwise,
clocks will prevent PER powerdomain from entering retention.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.'  This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.

The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

According to the GPIO 'Wakeup and Interrupt' section of the TRM[1],
wake-up requests can only be generated on edge transitions.

Also for OMAP3, only edge GPIOs may lose interrupts when PER enters
RET/OFF state, this is addressed by gpio prepare|resume idle functions

[1] Section 25.5.3.1 OMAP34xx_ES3.1_TRM_V_Q
Signed-off-by: NChunqiu Wang <cqwang@motorola.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add V4L2 DSS driver support in device.c
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Retry commands with UNIT_ATTENTION sense codes to fix ext3/ext4 I/O error
  [SCSI] Enable retries for SYNCRONIZE_CACHE commands to fix I/O error
  [SCSI] scsi_debug: virtual_gb ignores sector_size
  [SCSI] libiscsi: regression: fix header digest errors
  [SCSI] fix locking around blk_abort_request()
  [SCSI] advansys: fix narrow board error path

commit 672917dc ("cpuidle: menu governor: reduce latency on exit")
added an optimization, where the analysis on the past idle period moved
from the end of idle, to the beginning of the new idle.

Unfortunately, this optimization had a bug where it zeroed one key
variable for new use, that is needed for the analysis.  The fix is
simple, zero the variable after doing the work from the previous idle.

During the audit of the code that found this issue, another issue was
also found; the ->measured_us data structure member is never set, a
local variable is always used instead.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Cc: Corrado Zoccolo <czoccolo@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://neil.brown.name/md:
  md: restore ability of spare drives to spin down.
  md/raid6: Fix raid-6 read-error correction in degraded state

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia: fix compilation after 16bit state locking changes
  pcmcia: order userspace suspend and resume requests
  pcmcia: avoid pccard_validate_cis failure in resume callpath

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  blk-cgroup: Fix an RCU warning in blkiocg_create()
  blk-cgroup: Fix RCU correctness warning in cfq_init_queue()
  drbd: don't expose failed local READ to upper layers

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/ttm: Remove the ttm_bo_block_reservation() function.
  drm/ttm: Remove some leftover debug messages.
  drm/radeon: async event synchronization for drmWaitVblank

Move initialization of the virtio framework before the initialization of
mtd, so that block2mtd can be used on virtio-based block devices.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15644Signed-off-by: NStijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Fix RCU issues in the NFSv4 delegation code
  NFSv4: Fix the locking in nfs_inode_reclaim_delegation()

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: sleep: init_set_sci_en_on_resume for Dell Studio 155x
  ACPI: fix acpi_hest_firmware_first_pci() caused oops
  sbshc: acpi_device_class "smbus_host_controller" too long
  power_meter: acpi_device_class "power_meter_resource" too long
  acpi_pad: "processor_aggregator" name too long
  PNP: don't check for conflicts with bridge windows
  ACPI: DMI init_set_sci_en_on_resume for multiple Lenovo ThinkPads
  PNPACPI: compute Address Space length rather than using _LEN
  ACPI: silence kmemcheck false positive

* 'v4l_for_2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB: pxa_camera: move fifo reset direct before dma start
  V4L/DVB: video: testing unsigned for less than 0
  V4L/DVB: mx1-camera: compile fix
  V4L/DVB: budget: Oops: "BUG: unable to handle kernel NULL pointer 	dereference"
  V4L/DVB: ngene: Workaround for stuck DiSEqC pin
  V4L/DVB: saa7146: fix regression of the av7110/budget-av driver
  V4L/DVB: v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
  V4L/DVB: feature-removal: announce videotext.h removal
  V4L/DVB: V4L - vpfe capture - fix for kernel crash
  V4L/DVB: gspca: make usb id 0461:0815 get handled by the right driver
  V4L/DVB: gspca - stv06xx: Remove the 046d:08da from the stv06xx driver
  V4L/DVB: gspca - sn9c20x: Correct onstack wait_queue_head declaration
  V4L/DVB: saa7146: fix up bytesperline if it is an impossible value
  V4L/DVB: V4L: vpfe_capture - free ccdc_lock when memory allocation fails
  V4L/DVB: V4L - Makfile:Removed duplicate entry of davinci
  V4L/DVB: omap24xxcam: potential buffer overflow

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: create rcu_my_thread_group_empty() wrapper
  memcg: css_id() must be called under rcu_read_lock()
  cgroup: Check task_lock in task_subsys_state()
  sched: Fix an RCU warning in print_task()
  cgroup: Fix an RCU warning in alloc_css_id()
  cgroup: Fix an RCU warning in cgroup_path()
  KEYS: Fix an RCU warning in the reading of user keys
  KEYS: Fix an RCU warning

Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down.  Device failure/removal
etc are still recorded on spares.

However commit 51d5668c broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:

   This means that the alignment between 'odd/even' and
    'clean/dirty' might take a little longer to attain,

how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.

So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately.  There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update).  We just piggy-back on that.
Reported-by: NJoe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
Cc: stable@kernel.org