Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 05 11月, 2017 4 次提交
  3. 04 11月, 2017 3 次提交
  5. 03 11月, 2017 19 次提交
  7. 02 11月, 2017 5 次提交
    • G
      License cleanup: add SPDX GPL-2.0 license identifier to files with no license · b2441318
      由 Greg Kroah-Hartman 提交于 
      Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b2441318
    • K
      tcp_nv: fix division by zero in tcpnv_acked() · 4eebff27
      由 Konstantin Khlebnikov 提交于 
      Average RTT could become zero. This happened in real life at least twice.
This patch treats zero as 1us.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: NLawrence Brakmo <Brakmo@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4eebff27
    • J
      net: sched: remove tc_can_offload check from egdev call · 7612fb03
      由 Jiri Pirko 提交于 
      Since the only user, mlx5 driver does the check in
mlx5e_setup_tc_block_cb, no need to check here.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7612fb03
    • J
      net: sched: move the can_offload check from binding phase to rule insertion phase · 44ae12a7
      由 Jiri Pirko 提交于 
      This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      44ae12a7
    • N
      net: bridge: add notifications for the bridge dev on vlan change · 92899063
      由 Nikolay Aleksandrov 提交于 
      Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      92899063
  9. 01 11月, 2017 9 次提交
    • E
      net: dsa: lan9303: lan9303_rcv set skb->offload_fwd_mark · f8497729
      由 Egil Hjelmeland 提交于 
      The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.

One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f8497729
    • E
      net: dsa: lan9303: Add STP ALR entry on port 0 · e9292f2c
      由 Egil Hjelmeland 提交于 
      STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.

Add an ALR entry with STP state override to fix that.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e9292f2c
    • E
      net: dsa: lan9303: Transmit using ALR when unicast · 909fb9ae
      由 Egil Hjelmeland 提交于 
      lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.

This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      909fb9ae
    • P
      ipv4: fix validate_source for VRF setup · 032a4802
      由 Paolo Abeni 提交于 
      David reported breakages of VRF scenarios due to the
commit 6e617de8 ("net: avoid a full fib lookup when rp_filter is
disabled."): the local addresses based test is too strict when VRFs
are in place.

With this change we fall-back to a full lookup when custom fib rules
are in place; so that we address the VRF use case and possibly other
similar issues in non trivial setups.

v1 -> v2:
 - fix build breakage when CONFIG_IP_MULTIPLE_TABLES is not defined,
   reported by the kbuild test robot
Reported-by: NDavid Ahern <dsahern@gmail.com>
Fixes: 6e617de8 ("net: avoid a full fib lookup when rp_filter is disabled.")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      032a4802
    • W
      sctp: fix error return code in sctp_send_add_streams() · dc82673f
      由 Wei Yongjun 提交于 
      Fix to returnerror code -ENOMEM from the sctp_make_strreset_addstrm()
error handling case instead of 0. 'retval' can be overwritten to 0 after
call sctp_stream_alloc_out().

Fixes: e090abd0 ("sctp: factor out stream->out allocation")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dc82673f
    • E
      tcp: fix tcp_mtu_probe() vs highest_sack · 2b7cda9c
      由 Eric Dumazet 提交于 
      Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.

Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.

If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.

Bad things would then happen, including infinite loops.

This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.

Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.

Fixes: a47e5a98 ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NAlexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: NRoman Gushchin <guro@fb.com>
Reported-by: NOleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2b7cda9c
    • E
      ipv6: addrconf: increment ifp refcount before ipv6_del_addr() · e669b869
      由 Eric Dumazet 提交于 
      In the (unlikely) event fixup_permanent_addr() returns a failure,
addrconf_permanent_addr() calls ipv6_del_addr() without the
mandatory call to in6_ifa_hold(), leading to a refcount error,
spotted by syzkaller :

WARNING: CPU: 1 PID: 3142 at lib/refcount.c:227 refcount_dec+0x4c/0x50
lib/refcount.c:227
Kernel panic - not syncing: panic_on_warn set ...

CPU: 1 PID: 3142 Comm: ip Not tainted 4.14.0-rc4-next-20171009+ #33
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:52
 panic+0x1e4/0x41c kernel/panic.c:181
 __warn+0x1c4/0x1e0 kernel/panic.c:544
 report_bug+0x211/0x2d0 lib/bug.c:183
 fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
 do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
 do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
 do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
 invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_dec+0x4c/0x50 lib/refcount.c:227
RSP: 0018:ffff8801ca49e680 EFLAGS: 00010286
RAX: 000000000000002c RBX: ffff8801d07cfcdc RCX: 0000000000000000
RDX: 000000000000002c RSI: 1ffff10039493c90 RDI: ffffed0039493cc4
RBP: ffff8801ca49e688 R08: ffff8801ca49dd70 R09: 0000000000000000
R10: ffff8801ca49df58 R11: 0000000000000000 R12: 1ffff10039493cd9
R13: ffff8801ca49e6e8 R14: ffff8801ca49e7e8 R15: ffff8801d07cfcdc
 __in6_ifa_put include/net/addrconf.h:369 [inline]
 ipv6_del_addr+0x42b/0xb60 net/ipv6/addrconf.c:1208
 addrconf_permanent_addr net/ipv6/addrconf.c:3327 [inline]
 addrconf_notify+0x1c66/0x2190 net/ipv6/addrconf.c:3393
 notifier_call_chain+0x136/0x2c0 kernel/notifier.c:93
 __raw_notifier_call_chain kernel/notifier.c:394 [inline]
 raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
 call_netdevice_notifiers_info+0x32/0x60 net/core/dev.c:1697
 call_netdevice_notifiers net/core/dev.c:1715 [inline]
 __dev_notify_flags+0x15d/0x430 net/core/dev.c:6843
 dev_change_flags+0xf5/0x140 net/core/dev.c:6879
 do_setlink+0xa1b/0x38e0 net/core/rtnetlink.c:2113
 rtnl_newlink+0xf0d/0x1a40 net/core/rtnetlink.c:2661
 rtnetlink_rcv_msg+0x733/0x1090 net/core/rtnetlink.c:4301
 netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2408
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4313
 netlink_unicast_kernel net/netlink/af_netlink.c:1273 [inline]
 netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1299
 netlink_sendmsg+0xa4a/0xe70 net/netlink/af_netlink.c:1862
 sock_sendmsg_nosec net/socket.c:633 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:643
 ___sys_sendmsg+0x75b/0x8a0 net/socket.c:2049
 __sys_sendmsg+0xe5/0x210 net/socket.c:2083
 SYSC_sendmsg net/socket.c:2094 [inline]
 SyS_sendmsg+0x2d/0x50 net/socket.c:2090
 entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x7fa9174d3320
RSP: 002b:00007ffe302ae9e8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffe302b2ae0 RCX: 00007fa9174d3320
RDX: 0000000000000000 RSI: 00007ffe302aea20 RDI: 0000000000000016
RBP: 0000000000000082 R08: 0000000000000000 R09: 000000000000000f
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe302b32a0
R13: 0000000000000000 R14: 00007ffe302b2ab8 R15: 00007ffe302b32b8

Fixes: f1705ec1 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e669b869
    • V
      net: display hw address of source machine during ipv6 DAD failure · da13c59b
      由 Vishwanath Pai 提交于 
      This patch updates the error messages displayed in kernel log to include
hwaddress of the source machine that caused ipv6 duplicate address
detection failures.

Examples:

a) When we receive a NA packet from another machine advertising our
address:

ICMPv6: NA: 34:ab:cd:56:11:e8 advertised our address 2001:db8:: on eth0!

b) When we detect DAD failure during address assignment to an interface:

IPv6: eth0: IPv6 duplicate address 2001:db8:: used by 34:ab:cd:56:11:e8
detected!

v2:
    Changed %pI6 to %pI6c in ndisc_recv_na()
    Chaged the v6 address in the commit message to 2001:db8::
Suggested-by: NIgor Lubashev <ilubashe@akamai.com>
Signed-off-by: NVishwanath Pai <vpai@akamai.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      da13c59b
    • G
      net: netrom: nr_route: mark expected switch fall-throughs · 31f74f0f
      由 Gustavo A. R. Silva 提交于 
      In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      31f74f0f