The ordering of operations was messed up in the init and as a result when
VMDQ was enabled we were trying to enable TX rings before setting the VFTE
bits. This resulted in a ring that appeared to fail to enable when in fact
it was blocked because the VFTE bits were cleared after the reset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds NAPI support to the qeth layer 2 and layer 3
discipline. It is important to understand that we can not enable/disable
IRQs as usual, we have to use the corresponding new QDIO interface.
Also to not overdraw the budget we have to stop and restart buffer
processing at any point during processing a bulk of QDIO buffers.
Having the driver NAPI enabled it is possible to turn on GRO for the
layer 3 discipline.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the claw code calls ccwgroup_remove_ccwdev(), we need to make sure
CCWGROUP is enabled when CLAW is enabled.  Otherwise we hit fun undefined
references at build time:
ERROR: "ccwgroup_remove_ccwdev" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_probe_ccwdev" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_driver_register" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_driver_unregister" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_create_from_string" [drivers/s390/net/claw.ko] undefined!
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Format an ipv6 address using vsprintf extensions.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the qdio API to allow polling in the upper-layer driver. This
is needed by qeth to use NAPI.

To use the new interface the upper-layer driver must specify the
queue_start_poll(). This callback is used to signal the upper-layer
driver that is has initiative and must process the inbound queue by
calling qdio_get_next_buffers(). If the upper-layer driver wants to
stop polling it calls qdio_start_irq().

Since adapter interrupts are not completely stoppable qdio implements
a software bit QDIO_QUEUE_IRQS_DISABLED to safely disable interrupts for an
input queue.

The old interface is preserved and will be used as is by zfcp.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several users report issues with 32-bit adapters when plugged
into PCI slots in machines with >= 4GB ram.  In particular AMD
systems with HyperTransport to PCI bridges seem to trigger the
issue, but it isn't limited to only them.

This issue is not easily reproducible here, yet still continues
to occur in the field.  For e1000 on PCI devices, just disable DMA
addresses over the 4GB boundary when in PCI (not PCI-X) mode, to
prevent the issue from continuing to pop up.  The performance
impact for this is negligible.

The code was refactored to move the init of the hw struct to its
own function. This allows the init to be called very early in
probe, which then allows using hw-> members for this fix.

A slight refactor to the DMA mask code was done for minor
correctness based on the instructions in DMA-API-HOWTO.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces cx82310_eth driver - driver for USB ethernet port of
ADSL routers based on Conexant CX82310 chips. Such routers usually have
ethernet port(s) too which are bridged together with the USB ethernet port,
allowing the USB-connected machine to communicate to the network (and also
internet through the ADSL, of course).

This is my first driver, so please check thoroughly. As there's no protocol
documentation, it was done with usbsnoop dumps from Windows driver, some
parts (the commands) inspired by cxacru driver and also other usbnet drivers.
The driver passed my testing - some real work and also pings sized from 0 to
65507 B.

The only problem I found is the ifconfig error counter. When I return 0 (or 1
but empty skb) from rx_fixup(), usbnet increases the error counter although
it's not an error condition (because packets can cross URB boundaries). Maybe
the usbnet should be fixed to allow rx_fixup() to return empty skbs (or some
other value, e.g. 2)?

The USB ID of my device is 0x0572:0xcb01 which conflicts with some ADSL modems
using cxacru driver (they probably use the same chipset but simpler
firmware). The modems seem to use bDeviceClass 0 and iProduct "ADSL USB
MODEM", my router uses bDeviceClass 255 and iProduct "USB NET CARD". The
driver matches only devices with class 255 and checks for the iProduct string
during init. I already posted a patch for the cxacru driver to ignore these
devices.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Use napi_gro_receive() and vlan_gro_receive()
- Enable GRO by default

Tested on a RTL8111/8168 adapter
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note that the date format was fixed.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change LED scheme for dual-media
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add required changes in order to support dual-media boards.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Group all PHY specific functions together to have an organized code
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the needed changes for the new scheme especially around PHY
initialization, and link detection.
- The get_emac_base function was changed to enable setting different MAC
access setting for each PHY based of external configuration.
- As a part of the dual-media preparation, the save_spirom_version was
modified to accept a PHY specific version address to be saved in the
shmem. This will enable to save more than single spirom version in

different locations.
- The test_link function was changed also as a preparation for the
dual-media upcoming changes
- Duplicate initialization logic was removed from the
link_setting_status and link_initialize functions
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all PHY specific logic from bnx2x_main into bnx2x_link.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control implementation is split to be done in each PHY function.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In previous patch, common PHY functions were split in simple way to
allow easy diff. This patch comes to align code in the new functions.
In addition, the non-production BCM8072 PHY was removed.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the code into PHY oriented functions, and for that a new structure
is defines for each PHY which contain PHY properties and its own
functions. This also enables to encapsulate all PHY specific operations
into the PHY functions. During initialization, the PHYs will be probed
by the "bnx2x_phy_probe" function to detect which PHYs exist on-board,
and configure them accordingly. Note that the ext_phy_reset
implementation was incorporated in the ext_phy_init since it is actually
part of the PHY initialization procedure.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Start building the infrastructure for dual media by adding new component
of PHY which will be used all along the function. Modify function to
work with this component instead of the link_params.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The values didn't match the title after removing the LRO
statistics in commit fa37a958Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If failed to get skb frags using napi_get_frags(),
the packet is dropped.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function has an unsigned return type, but returns a negative constant
to indicate an error condition.  The result of calling the function is
always stored in a variable of type (signed) int, and thus unsigned can be
dropped from the return type.

A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@exists@
identifier f;
constant C;
@@

 unsigned f(...)
 { <+...
*  return -C;
 ...+> }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CHELSIO_T1_1G ifdef isn't necessary at this point, because it is
checked in an outer ifdef level already and has no effect here.
Signed-off-by: NChristian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert jeprintk to pr_err
Remove jeprintk macro define
Remove periods from end of logging messages
Coalesce format strings
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This showed up in my audit because we use strcpy() to copy "ds" into a
32 character buffer inside the isdn_tty_dial() function.  But it turns
out that we only ever use the first 32 characters so it's OK.  I have
changed the declaration to make the static checkers happy.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cs->ics.parm.setup.phone is a 32 character array.  In each of these
cases we're copying from a 35 character array into a 32 character array
so we should use strlcpy() instead of strcpy().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnad_set_rx_mode omit to unlock bna_lock on one fail path. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Debashis Dutt <ddutt@brocade.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this case, a device_node structure is stored in another structure that
is then freed without first decrementing the reference count of the
device_node structure.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression x;
identifier f;
position p1,p2;
@@

x@p1->f = \(of_find_node_by_path\|of_find_node_by_name\|of_find_node_by_phandle\|of_get_parent\|of_get_next_parent\|of_get_next_child\|of_find_compatible_node\|of_match_node\|of_find_node_by_type\|of_find_node_with_property\|of_find_matching_node\|of_parse_phandle\|of_node_get\)(...);
... when != of_node_put(x)
kfree@p2(x)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("call",p1)
cocci.print_secs("free",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an entry to the MAINTAINERS file for ibmveth, clean up the copyright
and add all authors. Change the name of the module to reflect the product name
over the last number of years.

Considering all the changes we have made, bump the driver version.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These files probably came across from the skeleton driver. Remove them.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had a driver specific assert function which wasn't enabled most of the
time. Convert them to BUG_ON and enable them all the time.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had a few cases where we returned success on error.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix most of the kernel coding style issues in ibmveth.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IbmVethNumBufferPools -> IBMVETH_NUM_BUFF_POOLS

Also change IBMVETH_MAX_MTU -> IBMVETH_MIN_MTU, it refers to the minimum
size not the maximum.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use netdev_err to standardise the error output.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use netdev_dbg to standardise the debug output.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These functions appear before their use, so we can remove the redundant
prototypes.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were using alloc_skb which doesn't create any headroom. Change it to
use netdev_alloc_skb to match most other drivers.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We export all the driver specific statistics via ethtool, so there is no need
to duplicate this in procfs.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables TCP checksum offload support for IPv6 on ibmveth.
This completely eliminates the generation and checking of the checksum
for IPv6 packets that are completely virtual and never touch a physical
network.  A basic TCPIPV6_STREAM netperf run showed a ~30% throughput
improvement when an MTU of 64000 was used.

This featured is enabled by default, as is the case for IPv4 checksum
offload.  When checksum offload is enabled the driver will negotiate
IPv4 and IPv6 offload with the firmware separately and enable what
is available.  As long as either IPv4 or IPv6 offload is supported
and enabled the device will report that checksum offload is enabled.
The device stats, available through ethtool, will display which
checksum offload features are supported/enabled by firmware.

Performance testing against a stock kernel shows no regression for IPv4
or IPv6 in terms of throughput or processor utilization with checksum
disabled or enabled.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>