The maximum DPLL multiplier (M) values for OMAP2xxx and OMAP3xxx are
one increment higher than they should be.  See for example the
OMAP242x TRM Rev X Section 5.10.6 "Clock Generator Registers" and the
OMAP36xx TRM Rev C Table 3-202 "CM_CLKSEL1_PLL".  Programming a 0 into
the DPLL's M register bitfield is valid for OMAP2/3 and indicates that
the DPLL should enter MN-bypass mode.  Also, increase the minimum
multiplier (M) value for the DPLL rate rounding code from 1 to 2, to
ensure that it does not inadvertently put the DPLL into bypass.

Note that the register documentation in the OMAP2xxx and OMAP3xxx TRMs
does not make clear that the actual DPLL divider value (the "N") is
the content of the appropriate register bitfield for the N value,
_plus one_.  (In other words, an N register bitfield of 0 indicates a
DPLL divider value of 1.)  This is only clearly documented in the
OMAP4430 TRM, in, for example, OMAP4430 TRM Rev A Table 3-1167
"CM_CLKSEL_DPLL_USB".

While here, update copyrights, add kerneldoc for struct dpll_data,
drop the unused struct dpll_data.max_tolerance field, remove some
unnecessary #includes in DPLL-related code, and replace the #include
of <linux/module.h> with <linux/list.h>, which is what was really
needed.  The OMAP4 clock autogenerator script has been updated
accordingly.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

DPLL4 for 3630 introduces a changed block called j type dpll, requiring
special divisor bits and additional reg fields. To allow for silicons to
use this, this is introduced as a flag and is enabled for 3630 silicon.
OMAP4 also has j type dpll for usb.

Tested with 3630 ZOOM3 and OMAP3430 ZOOM2
Signed-off-by: NRichard Woodruff <r-woodruff2@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NVishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: added some comments; updated copyrights and credits; fixed
 some style issues]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Rename clkops_noncore_dpll_ops for omap3 and omap4.
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rename the omap2_clk_init() in the OMAP2, 3, and 4 clock code to be
omap2xxx_clk_init(), omap3xxx_clk_init(), etc.  Remove all traces of
the (commented) old virt_prcm_set code from omap3xxx_clk_init() and
omap4xxx_clk_init(), since this will be handled with the OPP code that
is cooking in the PM branch.

After this patch, there should be very little else in the clock code
that blocks a multi-OMAP 2+3 kernel.  (OMAP2420+OMAP2430 still has some
outstanding issues that need to be resolved; this is pending on some
additions to the hwmod data.)
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The clockdomain related code being in place, it is not necessary to have
some part of the clock code commented out. This would help the validation of
the clockdomain functions using the clock level interfaces.
Signed-off-by: NAbhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

For all DPLL's the valid dividers are same as the values
to be programmed in the register. 0 is an invalid value.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>

This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>