The IWL_MAX_CMD_TFDS name for this constant is wrong, the
constant really indicates how many TBs we can use in the
driver for a single command TFD, rename the constant and
also add a comment explaining it.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The FH hardware will always write back to the scratch field
in commands, even host commands not just TX commands, which
can overwrite parts of the command. This is problematic if
the command is re-used (with IWL_HCMD_DFL_NOCOPY) and can
cause calibration issues.

Address this problem by always putting at least the first
16 bytes into the buffer we also use for the command header
and therefore make the DMA engine write back into this.

For commands that are smaller than 16 bytes also always map
enough memory for the DMA engine to write back to.

Cc: stable@vger.kernel.org
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Update Copyright notices to 2013.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

New transports may handle it internally for better performance.
Also move the tracing inside PRPH access which will make the
output more readable:

iwlwifi_dev_ioread_prph32: Read 0x0 from SCD_AGGR_SEL (32-bit)

instead of the corresponding accesses to HBUS_TARG_PRPH_*.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The printk message should say RX, not TX.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When tracing in iwlwifi, we get all data. Most of
the time, we don't need it, and it just takes up
a lot of extra space in the trace.

Make this optional by recording the data into two
separate trace events if it is needed. Without it,
record only the content of non-data and EAPOL TX
frames.

As a result, tracing without the data tracepoints
will record meta information including the 802.11
headers for all frames but will not record the
contents of data frames to reduce trace overhead.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Tracing commands builds an array of trace data
items even when the tracepoint is disabled.
Instead, loop in the tracepoint assignment.

This reduces overhead if tracing is compiled
into the driver but not enabled and slightly
reduces overall driver size as well:

   text	   data	    bss	    dec	    hex	filename
 114514	   6509	     48	 121071	  1d8ef	before/iwlwifi.ko
 114189	   6509	     48	 120746	  1d7aa	after/iwlwifi.ko
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

__get_str() is identical to (char *)__get_dynamic_array()
that is in the code now, substitute __get_str to make the
code more readable.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's one message that goes just over the
limit of 100 characters, so bump the limit to
110 to get rid of the warning from that.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since we're working on another mode/driver
inside iwlwifi, move the current one into a
subdirectory to more cleanly separate the
code. While at it, rename all the files.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Tracing used the priv pointer as an identifier,
which has the problem that we don't have it in
all code, and also some people say no pointers
should be "leaked" to userspace.

Use the device name instead, it is more useful
anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make iwlwifi record all debug messages into
tracing, even if debug_level is not enabled.
Due to the lack of APIs, the debug messages
are now recorded up to a max length of 100,
the only one above that is the RXON which is
not needed if you trace the commands as well
as it only dumps the command contents.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>

Update Copyright to 2012
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update Copyright to 2012
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The legacy IRQs could be read from a trace by their
IO accesses, but reading the ICT doesn't leave any
trace (pun intended ;-) ) so in order to see what
input they get we need to add specific tracepoints.

While at it, fix whitespace in two related places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The device tracing routines only use the priv pointer as an opaque
value.  Change from a typed iwl_priv pointer to a null pointer and
eliminate the need to include iwl_priv.h.  CMD_ASYNC is defined in
iwl_shared.h which is the only reason it is included.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No functional changes, just logging more information when uCode crash, also
change change the format.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The current "huge" command handling is a bit
confusing, and very limited since only one
command may be huge at a time. Additionally,
we often copy data around quite pointlessly
since we could instead map the existing scan
buffer for example and use it directly.

This patch makes that possible. The first
change is that multiple buffers may be given
to each command (this change was prepared
earlier so callsites don't need to change).
Each of those can be mapped attached to a TB
in the TFD, and the command header can use a
TB (the first one) in the TFD as well.

Doing this allows getting rid of huge commands
in favour of mapping existing buffers. The
beacon transmission is also optimised to not
copy the SKB at all but use multiple TBs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.

Cc: stable@kernel.org [2.6.32+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl-devtrace.h is used to declare and define trace points and
including iwl-dev.h from the file, which in turn includes other
generic headers, can lead to problems like generating duplicate copies
of generic trace points depending on the order of includes.  Don't
include iwl-dev.h from iwl-devtrace.h but include it from its users -
iwl-io.h and iwl-devtrace.c.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>

Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to help uCode debugging, adding the capability to provide
continuous uCode event logging function.

uCode events is located in round-robin event queue and filled by uCode,
by enable continuous event logging, driver check the write pointer
and log the newly added events in iwl_bg_ucode_trace() timer function.

There is still possibility of missing events if event queue being
wrapped before next event dump; but with this capability, we can have
much better understanding of the uCode behavior during runtime; it can
help to debug the uCode related issues.

Methods to enable/disable the continuous event log:
step 1: enable ucode trace timer
     "echo 1 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
step 2: start ftrace
     sudo ./trace-cmd record -e iwlwifi_ucode:* sleep 1d
step 3: stop ftrace
     sudo ./trace-cmd report trace.dat
step 4: disable ucode trace timer
     "echo 0 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"

use "ucode_tracing" debugfs file to display number of event
queue wrapped when driver attempt the continuous event logging. If event
queue being wrapped more than once when driver has opportunity to log
the event; it indicated there are events missing in the event log trace.

This continuous event log function only available for 4965 and newer
NICs.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since IO tracing is usually not needed and
generates a lot of data, separate it into
its own trace system so that we can always
enable iwlwifi:* and not have to worry about
getting too much data. If IO tracing is then
really needed we can enable iwlwifi_io:* in
addition and get that data.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To support byte writes to CSR_INT_COALESCING and CSR_INT_PERIODIC registers,
add iwl_write8(), including debug/trace support.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.

The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>