Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having
the skb mac header pointer set correctly since the following commit
present in kernels >= 3.9:

"net: reset mac header in dev_start_xmit()" (6d1ccff6)

Therefore we can safely use eth_hdr() and vlan_eth_hdr() instead of
skb->data now, which spares us some ugly type casts.

At the same time set the mac_header in batadv_dat_snoop_incoming_arp_request()
before sending the skb along the TX path.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

net/batman-adv/network-coding.c:1535:1-7: Replace memcpy with struct assignment

Generated by: coccinelle/misc/memcpy-assign.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Richard Cochran says:

====================
ptp: dynamic pin control

This patch series introduces a way of changing the auxiliary PTP
Hardware Clock functions (periodic output signals and time stamping
external signals) at run time. In the past on the netdev list, we have
discussed other ways to handle this, such as module parameters and
ethtool. This series implements a new PHC ioctl because that is the
most natural way. Users already activate the auxiliary functions via
the ioctls. The sysfs interface has also been expanded so that the pin
configuration can be programmed using shell scripts.

The first patch adds the new ioctls. The PHC subsystem does most of
the work of maintaining the function-to-pin mapping. Drivers will only
need to allocate and initialize a pin configuration table and also
provide a new method that validates a particular assignment.

Patches 5 and 6 just clean up a couple of issues in the phyter driver,
and the remaining patches actually hook the phyter's pins into the new
system.

* ChangeLog
** V3
   - simplify locking in the set pin logic
** V2
   - fix bug in sysfs code on init error path
   - rename ptp_setpin() to ptp_set_pinfunc()
   - rename .setpin() to .verify() in the driver interface
   - simplify ptp_find_pin() logic
   - use correct test when checking whether the pin with the
     calibration function is being reprogrammed
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver use the new pin configuration method when
programming the periodic output signal.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new pin configuration method when
programming the external time stamp input signals.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adapts the dp83640 driver to allow reconfiguration of which
auxiliary function goes on which pin. The functions may be reassigned
freely with the one exception of the calibration function.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phyter driver incorrectly feeds the value of the period into what
is in fact a pulse width register, resulting in the actual period
being twice the dialed value. This patch fixes the issue and renames a
variable to make the code at bit more clear.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up the input checking code on the external time stamp
function by using an unsigned rather than a signed channel index.

Also, this patch corrects the author's email address. When this macro
was last changed, the top level domain part of the email address was
left behind.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the sysfs hooks needed in order to get and set the
programmable pin settings.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a option to the test program that lists the
programmable pins on a PTP Hardware Clock device, assuming there
are any such pins. A second option lets the user reprogram the
auxiliary function of a single pin.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a pair of new ioctls to the PTP Hardware Clock device
interface. Using the ioctls, user space programs can query each pin to
find out its current function and also reprogram a different function
if desired.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: bcmgenet: misc fixes

This patch series contains some misc. fixes for the bcmgenet driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Laurent Pinchart says:

====================
sh_eth: Fix the race between open and MDIO bus registration

This patch series fixes the race condition that exists in the sh_eth driver
between network device open and MDIO bus registration. The actual fix is in
patch 4/5, with previous patches preparing the driver and patch 5/5 cleaning
up an unrelated issue.

I've based the idea on Sergei's attempt to fix the problem and can successfully
boot the Koelsch board over NFS with this series. I might have missed other
issues though, hence the RFC status.

The patches are based on top of the latest net-next master branch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.

Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is only a cleanup to use the right define for a panid field.
The broadcast address and panid broadcast is still the same value.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an issue which was introduced by commit
b70ab2e8 ("ieee802154: enforce
consistent endianness in the 802.15.4 stack").

The correct behaviour should be a check on the broadcast address field
which is 0xffff.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Reported-by: NJan Luebbe <jlu@pengutronix.de>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes the generic of_mdiobus_register parse the DT compatible string for
the pattern ethernet-phy-idAAAA.BBBB. If present it should be a value that
matches the phy-id register normally readable through MDIO.

When the ID is given the phy autoprobing is defeated and the phy is
created directly.

This is necessary to support phy's that cannot be autoprobed when
of_mdiobus_register is called. Specifically, my case has the phy in reset at
of_mdiobus_register, the reset is only released once the ethernet driver
starts, before it attaches to the phy.

Tested on ARM Kirkwood with phy id 0x01410e90 (Marvell 88E1318)
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This describes a compatible entry of the form:
  ethernet-phy-idAAAA,BBBB
Which is modelled after the PCI structured compatible entry
(pciVVVV,DDDD.SSSS.ssss.RR)

If present the OF core will be able to use this information to
directly create the correct phy without auto probing the bus.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Chan says:

====================
Adjust MTU as indicated by MBIM extended functional descriptor.

The MBIM extended functional descriptor, defined in "Universal Serial Bus
Communications Class Subclass Specification for Mobile Broadband Interface
Model, Revision 1.0, Errata-1" by USB-IF, indicates the operator preferred MTU
value via a wMTU field.

This patch set ensures that the initial MTU value set by cdc_ncm on a MBIM net
device does not exceed the wMTU value, provided the MBIM device exposes a MBIM
extended functional descriptor.

* Changelog
v2: Fixed a le16_to_cpu conversion issue in patch 2/2 pointed out by
    Bjørn Mork <bjorn@mork.no>
v3: No code changes. Resubmitted to include patch 1/2 as suggested by
    David Miller <davem@davemloft.net>
v4: No code changes. Resubmitted as suggested by David Miller:
    - Added a summary of the patch set
    - Carried the ACK from Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    - Added a specified the tree (net-next) to apply the patch set to
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.

This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: NBen Chan <benchan@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the MBIM extended functional descriptor structure
defined in "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF.
Signed-off-by: NBen Chan <benchan@chromium.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Add support for single port VFs

The mlx4 Firmware && driver expose both ports of the device through one PCI function.

This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.

This series from Matan Barak adds support for single ported VFs.

Since all the VF interaction with the firmware passes through the PF
 driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.

Series done against net-next commit 3ab428a4 "netfilter: Add missing
vmalloc.h include to nft_hash.c"

Roland, we send this through netdev, but if you have comments, will love
to hear them.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new syntax is added for the module parameters num_vfs and probe_vf.

  num_vfs=p1,p2,p1+p2
  probe_bf=p1,p2,p1+p2

Where p1(2) is the number of VFs on / probed VFs for physical
port1(2) and p1+p2 is the number of dual port VFs.

Single port VFs are currently supported only when the link type
for both ports of the device is Ethernet.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.

Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:

smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDaniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e100, igb, igbvf, ixgbe and ixgbevf.

Stefan adds a igb patch to enable the ability strip VLAN header information
for packets bound for a VM on i350 hardware.

Joe Perches provides patches for e100, igb, igbvf, ixgbe and ixgbevf to
convert the use of __constant_<foo> to just <foo> to align with the rest
of the kernel.

Don provides two fixes for ixgbe, first resolves a link issue with DA
cables where we were not always freeing the firmware/software semaphore
after grabbing it.  Second stops caching whether the management firmware
was enabled, however since this is not static, we really need to verify
with each check.

Jacob provides six fixes/cleanups for ixgbe, most notably, correct
the stop_mac_link_on d3() to check the Core Clock Disable bit before
stopping link and to fully check to see if manage firmware is running or
could be enabled before bringing down the link.  Fix flow control
auto-negation for KR/KX/K4 interfaces, since setting up MAC link, the
cached autoc value and current autoc value were being incorrectly used to
determine whether link reset is required.

Emil provides a fix for ixgbe where there was a chance for aggressive
start_ndo_zmit() callers to sneak packets between enabling the Tx queues
and the link coming up.  To resolve this, move the call to enable Tx
queues to after the link is established.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.

In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>