Incoming requests shouldn't require a local exchange if we're
just going to reply with one or two frames and don't expect
anything further.  Don't allocate exchanges for such requests
until requested by the upper-layer protocol.

The sequence is always NULL for new requests, so remove
that as an argument to request handlers.

Also change the first argument to lport->tt.seq_els_rsp_send
from the sequence pointer to the received frame pointer, to
supply the exchange IDs and destination ID info.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

For incoming ELS and FCP requests, we often don't require an
exchange and sequence, however, sometimes we do.  For those cases,
(primarily FCP requests for targets) add a function to set up
the exchange and sequence.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add functions to fill in an FC header given a request header.
These reduces code lines in fc_lport and fc_rport and works
without an exchange/sequence assigned.

fc_fill_reply_hdr() fills a header for a final reply frame.

fc_fill_hdr() which is similar but allows specifying the
f_ctl parameter.

Add defines for F_CTL values FC_FCTL_REQ and FC_FCTL_RESP.
These can be used for most request and response sequences.

v2 of patch adds a line to copy the frame encapsulation
info from the received frame.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

To pave the way for eliminating exchanges from incoming requests,
add simple inline fc_frame_sid() and fc_frame_did() functions
which get the FC_IDs from the frame header.  This can be almost
as efficient as getting them from the sequence/exchange.

Move ntohll, htonll, ntoh24 and hton24 to <scsi/fc_frame.h>
since we need them there and that's included by <scsi/libfc.h>
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The LOGO state hasn't been used in a while, except in a brief
transition to DELETE state while holding the rport mutex.
All port LOGO responses have been ignored as well as any timeout
if we don't get a response.

So this patch just removes LOGO state and simplifies the response handler.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add module parameter create_vn2vn that behaves like the create
parameter except that the new instance is created in FIP vn2vn mode.

This can be replaced once we change create to allow modifying
per-instance attributes before starting the instance.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In VN2VN mode, map_dest means to use the default VN2VN OUI.
Change code that uses the default FCoE OUI to use the one
set in the fcoe_ctlr struct.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When sending a FLOGI LS_ACC, which we only do in point-to-multipoint
mode, the MAC descriptor should have the granted MAC set to
0x0efd00 || D_ID.

When sending an LS_RJT, there should be no MAC descriptor.

When sending either an LS_ACC or LS_RJT, the subcode should indicate
an reply, not a request.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The FC-BB-6 committee is proposing a new FIP usage model called
VN_port to VN_port mode.  It allows VN_ports to discover each other
over a loss-free L2 Ethernet without any FCF or Fibre-channel fabric
services.  This is point-to-multipoint.  There is also a variant
of this called point-to-point which provides for making sure there
is just one pair of ports operating over the Ethernet fabric.

We add these new states:  VNMP_START, _PROBE1, _PROBE2, _CLAIM, and _UP.
These usually go quickly in that sequence.  After waiting a random
amount of time up to 100 ms in START, we select a pseudo-random
proposed locally-unique port ID and send out probes in states PROBE1
and PROBE2, 100 ms apart.  If no probe responses are heard, we
proceed to CLAIM state 400 ms later and send a claim notification.
We wait another 400 ms to receive claim responses, which give us
a list of the other nodes on the network, including their FC-4
capabilities.  After another 400 ms we go to VNMP_UP state and
should start interoperating with any of the nodes for whic we
receivec claim responses.  More details are in the spec.j

Add the new mode as FIP_MODE_VN2VN.  The driver must specify
explicitly that it wants to operate in this mode.  There is
no automatic detection between point-to-multipoint and fabric
mode, and the local port initialization is affected, so it isn't
anticipated that there will ever be any such automatic switchover.

It may eventually be possible to have both fabric and VN2VN
modes on the same L2 network, which may be done by two separate
local VN_ports (lports).

When in VN2VN mode, FIP replaces libfc's fabric-oriented discovery
module with its own simple code that adds remote ports as they
are discovered from incoming claim notifications and responses.
These hooks are placed by fcoe_disc_init().

A linear list of discovered vn_ports is maintained under the
fcoe_ctlr struct.  It is expected to be short for now, and
accessed infrequently.  It is kept under RCU for lock-ordering
reasons.  The lport and/or rport mutexes may be held when we
need to lookup a fcoe_vnport during an ELS send.

Change fcoe_ctlr_encaps() to lookup the destination vn_port in
the list of peers for the destination MAC address of the
FIP-encapsulated frame.

Add a new function fcoe_disc_init() to initialize just the
discovery portion of libfcoe for VN2VN mode.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Enhancement: add debug messages at all state transitions.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The FC-BB-6 committee is proposing a new FIP usage model called
VN_port to VN_port mode.  It allows VN_ports to discover each other
over a loss-free L2 Ethernet without any FCF or Fibre-channel fabric
services.  This is point-to-multipoint.  There is also a variant
of this called point-to-point which provides for making sure there
is just one pair of ports operating over the Ethernet fabric.

This patch defines the new message type and subtypes as well as
one new descriptor type used by VN2VN mode.

These are all still at the proposed stage and subject to change.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When an exchange is received with a FIP encapsulation, we need
to know that the response must be sent via FIP and what the original
ELS opcode was.  This becomes important for VN2VN mode, where we may
receive FLOGI or LOGO from several peer VN_ports, and the LS_ACC or
LS_RJT must be sent FIP-encapsulated with the correct sub-type.

Add a field to the struct fc_frame, fr_encaps, to indicate the
encapsulation values.  That term is chosen to be neutral and
LLD-agnostic in case non-FCoE/FIP LLDs might find it useful.

The frame fr_encaps is transferred from the ingress frame to the
exchange by fc_exch_recv_req(), and back to the outgoing frame
by fc_seq_send().

This is taking the last byte in the skb->cb array.  If needed,
we could combine the info in sof, eof, flags, and encaps
together into one field, but it'd be better to do that if
and when its needed.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The FIP proposal for VN_port to VN_port point-to-multipoint
operation requires a FLOGI be sent to each remote port.
The FLOGI is sent with the assigned S_ID and D_IDs of the
local and remote ports.  This and the response get
FIP-encapsulated for Ethernet.

Add FLOGI state to the remote port state machine.
This will be skipped if not in point-to-multipoint mode.

To reduce a little duplication between PLOGI and FLOGI
response handling, added fc_rport_login_complete(), which
handles the parameters for the rdata struct.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

For VN_port to VN_port mode, the transport sets the port_id and
there's no lport FLOGI.  This is similar to FC loop mode.

Add a point_to_multipoint flag that indicates the local port is in
point-to-multipoint mode.  This skips FLOGI and discovery.
It also skips resetting the port_id on resets other than link down.

Add function fc_lport_set_local_id() that sets the local port_id.
This is called by libfcoe on behalf of the low-level driver
to set the port_id when the link comes up.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

There are three modes that libfcoe currently supports, and a new one
is coming.  Change the fcoe_ctlr_init() interface to add the mode
desired.  This should not change any functionality.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

For VN_port to VN_port mode, FIP will do discovery and needs a
way to find its state from the local port or discovery structure.
It seems that any other LLD that implements its own discovery
would also need something like this.

Replace disc->lport with disc->priv, and use container_of to
find the lport.  We could use disc->priv for that, but
container_of is smaller and faster.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

It turns out most of the FIP work is now done from worker threads
or process context now, so there's no need to use a spin lock.

Change to use mutex instead of spin lock and delayed_work instead
of a timer.

This will make it nicer for the VN_port to VN_port feature that
will interact more with the libfc layers requiring that
spinlocks not be held.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add pre-zeroed space after the allocation for fc_rport_priv
for use by the lower-level driver.

This is primarily for VN2VN FIP mode, but could be used in
other ways someday.

The space required is specified in lport->rport_priv_size.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

To allow LLD to do lookups on rports without grabbing a mutex,
make them RCU-safe.  The caller of lport->tt.rport_lookup will
have the choice of holding disc_mutex or the rcu_read_lock().
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is  per FC-BB-5 Annex-D recommendation and per that
if address checking fails then drop the frame.

FIP code paths are already doing this so only needed for fcoe
frames.

The src address checking is limited to only fip mode since
this might break non-fip mode used in p2p due to used OUI
based addressing in some p2p code paths, going forward FIP
will be the only mode, therefore limited this to only FIP
mode so that it won't break non-fip p2p mode for now.

-v2
Removes FCOE packet type checking since fcoe_rcv is
registered to receive only FCoE type packets from netdev
and it is already checked by netdev.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The fc_fabric_logoff and fc_fabric_login are redundant
here after recently added fcoe_ctlr_link_down/up to
these functions, therefore this patch removes logoff
and login to only use link down and up here. This works
best for their current usages with fcoe DCB link down or up.

This also works well to avoid EIO errors when fcoe DCB link
goes down as lport state moves out of ready quickly from
fcoe_ctlr_link_down and that allows re-queuing timed out IOs
for this case also.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In this case, sync IO fails with EIO(5) errors as:-

"Thread:1 System call error:5 - Input/output error (::pwrite() failed)".

This is due to IO time out while libfc doing link down processing
to block all rports and if timed out IO was at last retry
attempt then it fails to user with EIO error followed by
these log messages.

[77848.612169] host2: rport bf0015: Delete port
[77848.612221] host2: rport e10aef: work delete
[77848.612232] host2: rport e10002: work event 3
[77848.612422] sd 2:0:1:1: [sdi] Unhandled error code
[77848.612426] sd 2:0:1:1: [sdi] Result: hostbyte=DID_ERROR
driverbyte=DRIVER_OK
[77848.612431] sd 2:0:1:1: [sdi] CDB: Write(10): 2a 00 00 00 11 20 00 00 20 00
[77848.612445] end_request: I/O error, dev sdi, sector 4384
[77848.612553] sd 2:0:1:2: [sdj] Unhandled error code

To fix these EIO errors, such timed out incomplete IOs needs
to be re-queued without counting retry attempt and this patch
does that using DID_REQUEUE scsi code.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Analyzing fcoe with sparse currently fails. This is because struct
fcoe_rcv_info contains two enum members that have been declared with
__attribute__((packed)). Apparently gcc honors this attribute while sparse
ignores it. The result is that sizeof(struct fcoe_rcv_info)
== sizeof(struct sk_buff::cb) == 48 on a 64-bit system according to gcc, but
not according to sparse. The patch below modifies the definition of
struct fcoe_rcv_info such that gcc and sparse interpret this structure
definition in the same way. The current sparse output is as follows:

$ cd linux-2.6.34
$ make C=2 M=drivers/scsi/fcoe modules
 CHECK   drivers/scsi/fcoe/fcoe.c

include/scsi/fc_frame.h:81:9: error: invalid bitfield width, -1.
 CC [M]  drivers/scsi/fcoe/fcoe.o
 CHECK   drivers/scsi/fcoe/libfcoe.c

include/scsi/fc_frame.h:81:9: error: invalid bitfield width, -1.
drivers/scsi/fcoe/libfcoe.c:56:37: error: invalid initializer
Signed-off-by: NBart Van Assche <bart.vanassche@gmail.com>
Cc: jeykholt@cisco.com
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is exposed by a mpio test using EMC CLARiiON targets when LUN
tresspassing happens, the burst length from the XFER_READY for the
MODE SELECT(10) is 19 bytes, much smaller than FC_MIN_MAX_PAYLOAD as
256 bytes. This patch removes the related two WARN_ON()s.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch is to add next generation of Dell iSCSI PowerVault
controller MD36xxi into RDAC device list.
Signed-off-by: NYanqing Liu <Yanqing_Liu@Dell.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The check to test that "bus_no" was valid came after we had already used
it as an array offset.  This patch moves it forward.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

FCoE Related Fixes
- Correct find-next-FCF routine so that it searches at next FCF rather
  than current one.
- Enhanced round-robin FCF failover algorithm to re-start on "New FCF"
  async event
- Update the manner in which we look at FCFs while they may be in
  their discovery state.
- Use LPFC_FCOE_NULL_VID macro when checkinf for valid vlan_id for FCF
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- BSG interface related:
  - Fix node reference count if node is active
  - Warn if we're overwriting an active CT context

- Discovery related:
  - Clear "Ignore Reg Login" flag when purging mailbox queue
  - Pay attention to return code for fc_block_scsi_eh()
  - Stall device loss code if we're almost done when it fires
    (we're logged in, but PRLI is outstanding)

- Bugs
  - Correct DIF code for endianness issues
  - Correct where we had missed points to check txq on i/o
    completion/cleanup
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Setting the resource type in the ipr_update_res_entry function was incorrect in
that the top 4 bits were masked off.  The assignment has been updated to no
longer mask those bits.

Then, two new attributes were added to allow the user space utilities to more
easily get information.  The resource_type sdev attribute is set for all devices
in the adapter's configuration table and indicates the type of device.  The
fw_type shost attribute indicates the firmware type supported by the adapter.

Finally, the resource_path attribute was changed to be mode S_IRUGO.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The method of transitioning to operational for new adapters includes using
initialization stages.  The current stage is indicated via a register read.
The final good stage in the sequence is "operational" but does not necessarily
indicate that the driver can proceed.  There is another bit that gets set in the
adapter->host interrupt register when the adapter has completed enough of its
bringup such that it can accept commands.  The driver was not checking that
bit before proceeding which led to intermittent errors and adapter resets.

The fix is to check the "transition to operational" bit in the interrupt
register after detecting that the initialization stage is "operational" and
only proceed if both are set.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

be2iscsi driver should #include linux/if_ether.h since it uses
sysfs_format_mac().

It should also depend on NET since it selects SCSI_ISCSI_ATTRS,
which depends on NET.

These changes fix a build error when CONFIG_NET is not enabled:
ERROR: "sysfs_format_mac" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch fixes a bug where the buffer was being freed as soon as
 submission to HW is done.
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch removes a Debug Print in the IO path
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch limits max_xmit_length to 64K incase older
utilities are used
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch ensures that the same ITT is maintained across
all login pdu's
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

These changes allow the driver to support crashdump. We need to reset the
chip incase of a crashdump
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch  frees tags that are already allocated in case of
failure
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>