This is more consistent and gets us closer to the Sparc code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is more consistent and gets us closer to the Sparc code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

        heirarchical, hierachical -> hierarchical
        heirarchy, hierachy -> hierarchy
Signed-off-by: NUwe Kleine-König <zeisberg@informatik.uni-freiburg.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

For PAPR partitions with large amounts of memory, the firmware has an
alternative, more compact representation for the information about the
memory in the partition and its NUMA associativity information.  This
adds the code to the kernel to parse this alternative representation.

The other part of this patch is telling the firmware that we can
handle the alternative representation.  There is however a subtlety
here, because the firmware will invoke a reboot if the memory
representation we request is different from the representation that
firmware is currently using.  This is because firmware can't change
the representation on the fly.  Further, some firmware versions used
on POWER5+ machines have a bug where this reboot leaves the machine
with an altered value of load-base, which will prevent any kernel
booting until it is reset to the normal value (0x4000).  Because of
this bug, we do NOT set fake_elf.rpanote.new_mem_def = 1, and thus we
do not request the new representation on POWER5+ and earlier machines.
We do request the new representation on POWER6, which uses the
ibm,client-architecture-support call.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns).  The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set.  As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.

The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing.  Two users have successfully booted their
powerpcs with it (one an ibook G4).  It has also been boot tested on x86,
x86_64, ppc64 and ia64.  Please merge for 2.6.19-rc2.

Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix.  Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Size zones and holes in an architecture independent manner for Power.

[judith@osdl.org: build fix]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Keith Mannthey" <kmannth@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

powerpc core changes.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Make notifier_blocks associated with cpu_notifier as __cpuinitdata.

__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Change of_node_to_nid() to traverse the device tree, looking for a numa id.
Cell uses this to assign ids to SPUs, which are children of the CPU node.
Existing users of of_node_to_nid() are altered to use of_node_to_nid_single(),
which doesn't do the traversal.

Export an attach_sysdev_to_node() function, allowing system devices (eg.
SPUs) to link themselves into the numa topology in sysfs.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Quieten some of the debug ram config output. we already print out available
memory at KERN_INFO level.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The return statement is to prevent `warning: 'nid' might be used uninitialized
in this function'.

Cc: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We can plug the boot cpu into its node independently of whether numa
topology is detected.  And numa_setup_cpu does the right thing for all
cases now, so remove special-casing for non-numa from the cpu hotplug
callback.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The powerpc numa code unconditionally onlines all nodes from 0 to the
highest node id found, regardless of whether cpus or memory are
present in the nodes.  This wastes 8K per node and complicates some
cpu and memory hotplug situations, such as adding a resource that
doesn't map to one of the nodes discovered at boot.

Set nodes online as resources are scanned.  Fall back to node 0 only
when we're sure this isn't a NUMA machine.

Instead of defaulting to node 0 for cases of hot-adding a resource
which doesn't belong to any initialized node, assign it to the first
online node.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Code to handle Power4's invalid node id (0xffff) is duplicated for cpu
and memory.  Better to handle this case in one place --
of_node_to_nid.  Overall behavior should be unchanged.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Since we effectively treat the domain ids given to us by firmare as
logical node ids, make this explicit (basically s/numa_domain/nid/).

No functional changes, only variable and function names are modified.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

map_cpu_to_node does not need to be inline, it is never called in a
hot path.

map_cpu_to_node, numa_setup_cpu, and find_cpu_node can be marked
__cpuinit, as they are never used after boot if CONFIG_HOTPLUG_CPU=n.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add debug statement for map_cpu_to_node; it's useful for cpu hotplug.

Clarify debug statement about not finding the numa reference points
property.

Don't print a meaningless associativity depth (-1) on non-numa systems.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

At boot, the numa code is assigning boot_cpuid to node 0
unconditionally.  Basically, numa_setup_cpu is being stupid about it,
but this is the minimal fix -- just call numa_setup_cpu(boot_cpuid)
later, after all nodes have been set online.
Signed-off-by: NNathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently most callers of lmb_alloc() don't check if it worked or not, if it
ever does weird bad things will probably happen. The few callers who do check
just panic or BUG_ON.

So make lmb_alloc() panic internally, to catch bugs at the source. The few
callers who did check the result no longer need to.

The only caller that did anything interesting with the return result was
careful_allocation(). For it we create __lmb_alloc_base() which _doesn't_ panic
automatically, a little messy, but passable.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The system will oops if an attempt is made to add memory to an
empty node/zone.  This patch prevents adding memory to an empty
node.  The code to dynamically add a node/zone is non-trivial.
This patch is temporary and will be removed when the ability
to dynamically add a node/zone is complete.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We used to print a NUMA cpu summary at boot before the hotplug cpu code
was added. This has been useful for catching machine configuration as
well as firmware bugs in the past.

This patch restores that functionality. An example of the output is:

Node 0 CPUs: 0-7
Node 1 CPUs: 8-15
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Milton has proposed that we should support a "linux,usable-memory" property
on memory nodes which describes, in preference to "reg", the regions of memory
Linux should use.

This facility is required for kdump to inform the second kernel which memory
it should use.
Signed-off-by: NHaren Myneni <haren@us.ibm.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This places dynamically added memory within the appropriate
numa node.  A new routine hot_add_scn_to_nid() replicates most of
the memory scanning code in parse_numa_properties().
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Here is an updated version of the patch that panics if no memory is
found as Nathan suggested.  I'm still concerned that panic strings
(not just the one added here) at this stage of booting do not show
up on my system.  But, that is an issue separate from this patch.

Combine get_mem_*_cells() routines to avoid multiple memory node
lookups.  Added missing of_node_put() call.  Changed variable names
to help with some confusion as to meaning.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This reverts f1fdc0117004d343698b9830e141491d5ae320d1 commit.

I started to add missing of_node_put() calls to the routines that
determine the number of cells for memory.  Decided to combine the
routines instead of making separate node lookups.  Changed variable
names to help with some confusion as to meaning.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This bug exists in the current code and prevents machines from booting
with numa enabled if there is a node that does not contain memory.
Workaround is to boot with 'numa=off'.  Looks like a simple typo.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch should fix the crashes we have been seeing on 64-bit
powerpc systems with a memory hole when sparsemem is enabled.
I'd appreciate it if people who know more about NUMA and sparsemem
than me could look over it.

There were two bugs.  The first was that if NUMA was enabled but there
was no NUMA information for the machine, the setup_nonnuma() function
was adding a single region, assuming memory was contiguous.  The
second was that the loops in mem_init() and show_mem() assumed that
all pages within the span of a pgdat were valid (had a valid struct
page).

I also fixed the incorrect setting of num_physpages that Mike Kravetz
pointed out.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Convert to sparsemem and remove all the discontigmem code in the
process. This has a few advantages:

- The old numa_memory_lookup_table can go away
- All the arch specific discontigmem magic can go away

We also remove the triple pass of memory properties and instead create a
list of per node extents that we iterate through. A final cleanup would
be to change our lmb code to store extents per node, then we can reuse
that information in the numa code.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove ppc64 specific version of nr_cpus_node and use the generic one
provided.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Mostly this involves adding #include <asm/smp.h>, since that defines
things like boot_cpuid[_phys] and [gs]et_hard_smp_processor_id, which
are SMP-related but still needed on UP.  This incorporates fixes
posted by Olof Johansson and Heikki Lindholm.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line.  This puts the declaration
in system.h and the definition in mem.c.  This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This moves the remaining files in arch/ppc64/mm to arch/powerpc/mm,
and arranges that we use them when compiling with ARCH=ppc64.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A new option for SPARSEMEM is ARCH_SPARSEMEM_EXTREME.  Architecture
platforms with a very sparse physical address space would likely want to
select this option.  For those architecture platforms that don't select the
option, the code generated is equivalent to SPARSEMEM currently in -mm.
I'll be posting a patch on ia64 ml which uses this new SPARSEMEM feature.

ARCH_SPARSEMEM_EXTREME makes mem_section a one dimensional array of
pointers to mem_sections.  This two level layout scheme is able to achieve
smaller memory requirements for SPARSEMEM with the tradeoff of an
additional shift and load when fetching the memory section.  The current
SPARSEMEM -mm implementation is a one dimensional array of mem_sections
which is the default SPARSEMEM configuration.  The patch attempts isolates
the implementation details of the physical layout of the sparsemem section
array.

ARCH_SPARSEMEM_EXTREME depends on 64BIT and is by default boolean false.

I've boot tested under aim load ia64 configured for ARCH_SPARSEMEM_EXTREME.
 I've also boot tested a 4 way Opteron machine with !ARCH_SPARSEMEM_EXTREME
and tested with aim.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NBob Picco <bob.picco@hp.com>
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We no longer need the lmb code to know about abs and phys addresses, so
remove the physbase variable from the lmb_property struct.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If CONFIG_NUMA is set, some POWER 4 systems will fail to boot.  This is
because of special processing needed to handle invalid node IDs (0xffff) on
POWER 4.  My previous patch to handle memory 'holes' within nodes forgot to
add this special case for POWER 4 in one place.

In reality, I'm not sure that configuring the kernel for NUMA on POWER 4 makes
much sense.  Are there POWER 4 based systems with NUMA characteristics that
are presented by the firmware?  But, distros want one kernel for all systems
so NUMA is on by default in their kernels.  The patch handles those cases.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Provide hooks for PPC64 to allow memory models to be informed of installed
memory areas.  This allows SPARSEMEM to instantiate mem_map for the populated
areas.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Signed-off-by: NMartin Bligh <mbligh@aracnet.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!