When raid1/raid10 array fails to write to one of the drives, the request
is added to bio_end_io_list and finished by personality thread. The
thread doesn't handle it as long as MD_CHANGE_PENDING flag is set. In
case of external metadata this flag is cleared, however the thread is
not woken up. It causes request to be blocked for few seconds (until
another action on the array wakes up the thread) or to get stuck
indefinitely.

Wake up personality thread once MD_CHANGE_PENDING has been cleared.
Moving 'restart_array' call after the flag is cleared it not a solution
because in read-write mode the call doesn't wake up the thread.
Signed-off-by: NTomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: NShaohua Li <shli@fb.com>

If external metadata handler supports bad blocks and unacknowledged bad
blocks are present, don't report disk via sysfs as faulty. Such
situation can be still handled so disk just has to be blocked for a
moment. It makes it consistent with kernel state as corresponding rdev
flag is also not set.

When the disk in being unblocked there are few cases:
1. Disk has been in blocked and faulty state, it is being unblocked but
it still remains in faulty state. Metadata handler will remove it from
array in the next call.
2. There is no bad block support in external metadata handler and bad
blocks are present - put the disk in blocked and faulty state (see
case 1).
3. There is bad block support in external metadata handler and all bad
blocks are acknowledged - clear all flags, continue.
4. There is bad block support in external metadata handler but there are
still unacknowledged bad blocks - clear all flags, continue. It is fine
to clear Blocked flag because it was probably not set anyway (if it was
it is case 1). BlockedBadBlocks flag can also be cleared because the
request waiting for it will set it again when it finds out that some bad
block is still not acknowledged. Recovery is not necessary but there are
no problems if the flag is set. Sysfs rdev state is still reported as
blocked (due to unacknowledged bad blocks) so metadata handler will
process remaining bad blocks and unblock disk again.
Signed-off-by: NTomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: NShaohua Li <shli@fb.com>

Add new rdev flag which external metadata handler can use to switch
on/off bad block support. If new bad block is encountered, notify it via
rdev 'unacknowledged_bad_blocks' sysfs file. If bad block has been
cleared, notify update to rdev 'bad_blocks' sysfs file.

When bad blocks support is being removed, just clear rdev flag. It is
not necessary to reset badblocks->shift field. If there are bad blocks
cleared or added at the same time, it is ok for those changes to be
applied to the structure. The array is in blocked state and the drive
which cannot handle bad blocks any more will be removed from the array
before it is unlocked.

Simplify state_show function by adding a separator at the end of each
string and overwrite last separator with new line.
Signed-off-by: NTomasz Majchrzak <tomasz.majchrzak@intel.com>
Reviewed-by: NArtur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: NShaohua Li <shli@fb.com>

User is unable to access to input-X-yyy and feature-X-yyy where
X is a hex value and more than 9 (e.g. input-a-yyy, feature-b-yyy) in HID
sensor custom sysfs interface.
This is because when creating the attribute, the attribute index is
written to using %x (hex). However, when reading and writing values into
the attribute, the attribute index is scanned using %d (decimal). Hence,
user is unable to access to attributes with index in hex values
(e.g. 'a', 'b', 'c') but able to access to attributes with index in
decimal values (e.g. 1, 2, 3,..).
This fix will change input-%d-%x-%s and feature-%d-%x-%s to input-%x-%x-%s
and feature-%x-%x-%s in show_values() and store_values() accordingly.
Signed-off-by: NOoi, Joyce <joyce.ooi@intel.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.

But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.

This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: NEven Xu <even.xu@intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: NEven Xu <even.xu@intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: NEven Xu <even.xu@intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

dw_pcie_iatu_unroll_enabled() reads a dbi_base register.  Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init.  Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.

Fixes: a0601a47 ("PCI: designware: Add iATU Unroll feature")
Tested-by: NJames Le Cuirot <chewi@gentoo.org>
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJoao Pinto <jpinto@synopsys.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.

The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:

  i2c_register_driver()             i2c_del_adapter()
    driver_register()                 ...
      bus_add_driver()                ...
        ...                           bus_for_each_drv(..., __process_removed_adapter)
      ...                               i2c_do_del_adapter()
    ...                                   list_for_each_entry_safe(..., &driver->clients, ...)
    INIT_LIST_HEAD(&driver->clients);

To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().

The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:

% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
  Unable to handle kernel NULL pointer dereference at virtual address 00000000
  Internal error: Oops: 17 [#1] SMP ARM
  CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
  Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
  task: e5ada400 task.stack: e4936000
  PC is at i2c_do_del_adapter+0x20/0xcc
  LR is at __process_removed_adapter+0x14/0x1c
  Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
  Control: 10c5387d  Table: 35bd004a  DAC: 00000051
  Process sh (pid: 533, stack limit = 0xe4936210)
  Stack: (0xe4937d28 to 0xe4938000)
  Backtrace:
  [<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
  [<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
  [<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
  [<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
  [<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
  [<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
  [<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
  [<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
  [<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
  [<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
  [<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
  [<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
  [<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
  [<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
  [<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Like many similar devices it needs a quirk to work.
Issuing the request gets the device into an irrecoverable state.
Signed-off-by: NOliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix

  drivers/hid/intel-ish-hid/ipc/pci-ish.c:247:12: warning: ‘ish_suspend’ defined but not used [-Wunused-function]
   static int ish_suspend(struct device *device)
              ^
  drivers/hid/intel-ish-hid/ipc/pci-ish.c:282:12: warning: ‘ish_resume’ defined but not used [-Wunused-function]
   static int ish_resume(struct device *device)
            ^
by sticking them in the CONFIG_PM range too.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-input@vger.kernel.org
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When report count is more than one and report size is not 4 bytes, then we
need some packing into result buffer from the caller of function
sensor_hub_get_feature.
By default the value extracted from a field is 4 bytes from hid core
(using hid_hw_request(hsdev->hdev, report, HID_REQ_GET_REPORT)), even
if report size if less than 4 byte. So when we copy data to user buffer in
sensor_hub_get_feature, we need to only copy report size bytes even
when report count is more than 1. This is
not an issue for most of the sensor hub fields as report count will be 1
where we already copy only report size bytes, but some string fields
like description, it is a problem as the report count will be more than 1.
For example:
    Field(6)
      Physical(Sensor.OtherCustom)
      Application(Sensor.Sensor)
      Usage(11)
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
        Sensor.0306
      Report Size(16)
      Report Count(11)

Here since the report size is 2 bytes, we will have 2 additional bytes of
0s copied into user buffer, if we directly copy to user buffer from
report->field[]->value

This change will copy report size bytes into the buffer of caller for each
usage report->field[]->value. So for example without this change, the
data displayed for a custom sensor field "sensor-model":

76 00 101 00 110 00 111 00 118 00 111
(truncated to report count of 11)

With change

76 101 110 111 118 111 32 89 111 103 97
("Lenovo Yoga" in ASCII )
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:

    datagram_size:  The encoded size of the entire IP datagram.  The
    value of datagram_size [...] SHALL be one less than the value of
    Total Length in the datagram's IP header (see STD 5, RFC 791).

Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:

    ether1394_tx() /* transmit */
        ether1394_encapsulate_prep()
            hdr->ff.dg_size = dg_size - 1;

    ether1394_data_handler() /* receive */
        if (hdr->common.lf == ETH1394_HDR_LF_FF)
            dg_size = hdr->ff.dg_size + 1;
        else
            dg_size = hdr->sf.dg_size + 1;

Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.

Only firewire-net sets and gets datagram_size without this offset.  The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394.  (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
  - from OS X fail entirely,
  - from Win XP start out with a bunch of fragmented datagrams which
    time out, then continue with unfragmented datagrams because Win XP
    temporarily reduces the MTU to 576 bytes.

So let's fix firewire-net's datagram_size accessors.

Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed.  (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)

Cc: stable@vger.kernel.org
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams.  A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.

So, drop any packets carrying a fragment with offset + length larger
than datagram_size.

In addition, ensure that
  - GASP header, unfragmented encapsulation header, or fragment
    encapsulation header actually exists before we access it,
  - the encapsulated datagram or fragment is of nonzero size.
Reported-by: NEyal Itkin <eyal.itkin@gmail.com>
Reviewed-by: NEyal Itkin <eyal.itkin@gmail.com>
Fixes: CVE 2016-8633
Cc: stable@vger.kernel.org
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

virtio-gpu sends vblank events in virtio_gpu_crtc_atomic_flush, and
because of that it must be called for disabled planes too.  Ask
drm_atomic_helper_commit_planes to do that.

v2: update to use new drm_atomic_helper_commit_planes() API.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This fixes the irq allocation in this driver to not print:
 irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
 irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated

Which happens because the driver already called irq_alloc_descs()
and so the change to use irq_domain_add_simple resulted in calling
irq_alloc_descs() twice.

Modernize the irq allocation in this driver to use the
irq_domain_add_linear flow directly and eliminate the use of
irq_domain_add_simple/legacy

Fixes: ce931f57 ("gpio/mvebu: convert to use irq_domain_add_simple()")
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Check whether the kernel really supports power resources for a device,
otherwise the power might not be removed when the device is runtime
suspended (DSM should still work in these cases where PR does not).

This is a workaround for a problem where ACPICA and Windows 10 differ in
behavior. ACPICA does not correctly enumerate power resources within a
conditional block (due to delayed execution of such blocks) and as a
result power_resources is set to false even if _PR3 exists.

Fixes: 692a17dc ("drm/nouveau/acpi: fix lockup with PCIe runtime PM")
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98398Reported-and-tested-by: NRick Kerkhof <rick.2889@gmail.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Sylvain Lemieux reports the LPC32xx GPIO driver is broken since
commit 762c2e46 ("gpio: of: remove of_gpiochip_and_xlate() and
struct gg_data").  Probably, gpio-etraxfs.c and gpio-davinci.c are
broken too.

Those drivers register multiple gpio_chip that are associated to a
single OF node, and their own .of_xlate() checks if the passed
gpio_chip is valid.

Now, the problem is of_find_gpiochip_by_node() returns the first
gpio_chip found to match the given node.  So, .of_xlate() fails,
except for the first GPIO bank.

Reverting the commit could be a solution, but I do not want to go
back to the mess of struct gg_data.  Another solution here is to
take the match by a node pointer and the success of .of_xlate().
It is a bit clumsy to call .of_xlate twice; for gpio_chip matching
and for really getting the gpio_desc index.  Perhaps, our long-term
goal might be to convert the drivers to single chip registration,
but this commit will solve the problem until then.

Fixes: 762c2e46 ("gpio: of: remove of_gpiochip_and_xlate() and struct gg_data")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: NSylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When allocating a new line handle or event a file is allocated that it is
associated to. The file is attached to a file descriptor of the current
process and the file descriptor is returned to userspace using
copy_to_user(). If this copy operation fails the line handle or event
allocation is aborted, all acquired resources are freed and an error is
returned.

But the file struct is not freed and left attached to the userspace
application and even though the file descriptor number was not copied it is
trivial to guess. If a userspace application performs a IOCTL on such a
left over file descriptor it will trigger a use-after-free and if the file
descriptor is closed (latest when the application exits) a double-free is
triggered.

anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a
file descriptor for the current process and install the file struct in the
file descriptor. As soon as the file struct is installed in the file
descriptor it is accessible by userspace (even if the IOCTL itself hasn't
completed yet), this means uninstalling the fd on the error path is not an
option, since userspace might already got a reference to the file.

Instead anon_inode_getfd() needs to be broken into its individual steps.
The allocation of the file struct and file descriptor is done first, then
the copy_to_user() is executed and only if it succeeds the file is
installed.

Since the file struct is reference counted it can not be just freed, but
its reference needs to be dropped, which will also call the release()
callback, which will free the state attached to the file. So in this case
the normal error cleanup path should not be taken.

Cc: stable@vger.kernel.org
Fixes: d932cd49 ("gpio: free handles in fringe cases")
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Removal of this check was not properly amended to the original commit.

Cc: stable@vger.kernel.org
Fixes: 0c541332 ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.l.morris@oracle.com>

This inline function is unused on configurations
where dma_map/unmap are empty macros.

Make the function inline to avoid gcc errors because
of an unused static function.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

The local variable "err" will be set to an appropriate value
by a following statement.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kmalloc_array".

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Remove unused file config.c
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Commit c6017e79 ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:

WARNING: CPU: 3 PID: 121 at ./include/linux/dma-mapping.h:433
free_buf+0x1a8/0x288
Call Trace:
[<8040c538>] show_stack+0x74/0xc0
[<80757240>] dump_stack+0xd0/0x110
[<80430d98>] __warn+0xfc/0x130
[<80430ee0>] warn_slowpath_null+0x2c/0x3c
[<807e7c6c>] free_buf+0x1a8/0x288
[<807ea590>] remove_port_data+0x50/0xac
[<807ea6a0>] unplug_port+0xb4/0x1bc
[<807ea858>] virtcons_remove+0xb0/0xfc
[<807b6734>] virtio_dev_remove+0x58/0xc0
[<807f918c>] __device_release_driver+0xac/0x134
[<807f924c>] device_release_driver+0x38/0x50
[<807f7edc>] bus_remove_device+0xfc/0x130
[<807f4b74>] device_del+0x17c/0x21c
[<807f4c38>] device_unregister+0x24/0x38
[<807b6b50>] unregister_virtio_device+0x28/0x44

Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.

Fixes: c6017e79 ("virtio: console: add locks around buffer removal in port unplug path")
Cc: stable@vger.kernel.org
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

The following commit 'fad7b7b2 (virtio_balloon: Use a workqueue
instead of "vballoon" kthread)' has added a regression. Original code with
kthread starts the thread inside probe and checks the necessity to update
balloon inside the thread immediately.

Nowadays the code behaves differently. Work is queued only on the first
command from the host after the negotiation. Thus there is a window
especially at the guest startup or the module reloading when the balloon
size is not updated until the notification from the host.

This patch adds balloon size check at the end of the probe to match
original behaviour.
Signed-off-by: NKonstantin Neumoin <kneumoin@virtuozzo.com>
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

According to the spec, if the VIRTIO_RING_F_EVENT_IDX feature bit is
negotiated the driver MUST set flags to 0. Not dirtying the available
ring in virtqueue_disable_cb also has a minor positive performance
impact, improving L1 dcache load missed by ~0.5% in vring_bench.

Writes to the used event field (vring_used_event) are still unconditional.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: <stable@vger.kernel.org> # f277ec42 virtio_ring: shadow available
Cc: <stable@vger.kernel.org>
Signed-off-by: NLadi Prosek <lprosek@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Legacy virtio defines the virtqueue base using a 32-bit PFN field, with
a read-only register indicating a fixed page size of 4k.

This can cause problems for DMA allocators that allocate top down from
the DMA mask, which is set to 64 bits. In this case, the addresses are
silently truncated to 44-bit, leading to IOMMU faults, failure to read
from the queue or data corruption.

This patch restricts the coherent DMA mask for legacy PCI virtio devices
to 44 bits, which matches the specification.

Cc: stable@vger.kernel.org
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Benjamin Serebrin <serebrin@google.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.

To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.

This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.

Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.

Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.

In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 8d7533e5.

It introduced kbuild failures, new version coming.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.

At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP.  On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.

The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.

Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.

Fixes: f9baff50 ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>