- 05 11月, 2014 1 次提交
-
-
由 Sudip Mukherjee 提交于
commit "b5b4a41b" was dereferencing chip after it has been freed. This patch fixes that and at the same time removes some debugging messages, which are unnecessary, as they are just printing information about entry and exit from a function, and which switch-case it is executing. we can easily get from ftrace the information about the entry and exit from a function. Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 03 11月, 2014 1 次提交
-
-
由 Sudip Mukherjee 提交于
removed all references of snd_printk with the standard dev_* macro. [a few places degraded to dev_dbg(), too -- tiwai] Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 15 2月, 2010 2 次提交
-
-
由 Giuliano Pochini 提交于
Move the controls init code outside the init_hw() function because is must not be called during resume. This patch moves the code that initializes the card's controls with default valued from the init_hw() function into a separated set_mixer_defaults() function (one for each of the 16 supported cards). This change is necessary because during resume we must resurrect the hardware without losing the previous settings. set_mixer_defaults() must be called only once when the module is loaded. Signed-off-by: NGiuliano Pochini <pochini@shiny.it> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Giuliano Pochini 提交于
Changes the way the firmware is passed through functions. When CONFIG_PM is enabled the firmware cannot be released because the driver will need it again to resume the card. With this patch the firmware is passed as an index of the struct firmware card_fw[] in place of a pointer. That same index is then used to locate the firmware in the firmware cache. Signed-off-by: NGiuliano Pochini <pochini@shiny.it> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 16 3月, 2009 1 次提交
-
-
由 Giuliano Pochini 提交于
With this patch the drivers do not set the vmixer volume anymore at startup because it is actually the output volume of the voices and ALSA mandates that the volume must be 0 by default. Signed-off-by: NGiuliano Pochini <pochini@shiny.it> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 13 8月, 2008 1 次提交
-
-
由 Takashi Iwai 提交于
Kill snd_assert() in sound/pci/*, either removed or replaced with if () with snd_BUG_ON(). Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
- 29 6月, 2006 1 次提交
-
-
由 Giuliano Pochini 提交于
From: Giuliano Pochini <pochini@shiny.it>Add echoaudio sound drivers (darla20, darla24, echo3g, gina20, gina24, indigo, indigodj, indigoio, layla20, lala24, mia, mona) Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-