geneve:
- Merge __geneve_change_mtu back into geneve_change_mtu, set max_mtu
- This one isn't quite as straight-forward as others, could use some
  closer inspection and testing

macvlan:
- set min/max_mtu

tun:
- set min/max_mtu, remove tun_net_change_mtu

vxlan:
- Merge __vxlan_change_mtu back into vxlan_change_mtu
- Set max_mtu to IP_MAX_MTU and retain dynamic MTU range checks in
  change_mtu function
- This one is also not as straight-forward and could use closer inspection
  and testing from vxlan folks

bridge:
- set max_mtu of IP_MAX_MTU and retain dynamic MTU range checks in
  change_mtu function

openvswitch:
- set min/max_mtu, remove internal_dev_change_mtu
- note: max_mtu wasn't checked previously, it's been set to 65535, which
  is the largest possible size supported

sch_teql:
- set min/max_mtu (note: max_mtu previously unchecked, used max of 65535)

macsec:
- min_mtu = 0, max_mtu = 65535

macvlan:
- min_mtu = 0, max_mtu = 65535

ntb_netdev:
- min_mtu = 0, max_mtu = 65535

veth:
- min_mtu = 68, max_mtu = 65535

8021q:
- min_mtu = 0, max_mtu = 65535

CC: netdev@vger.kernel.org
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Tom Herbert <tom@herbertland.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Paolo Abeni <pabeni@redhat.com>
CC: Jiri Benc <jbenc@redhat.com>
CC: WANG Cong <xiyou.wangcong@gmail.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Pravin B Shelar <pshelar@ovn.org>
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Pravin Shelar <pshelar@nicira.com>
CC: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- set min/max_mtu in all hdlc drivers, remove hdlc_change_mtu
- sent max_mtu in lec driver, remove lec_change_mtu
- set min/max_mtu in x25_asy driver

CC: netdev@vger.kernel.org
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Kevin Curtis <kevin.curtis@farsite.co.uk>
CC: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu

CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
  max_mtu and/or min_mtu as needed)

r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)

lan78xx:
- Set max_mtu = 9000

asix_driver:
- max_mtu = 16384 for ax88178 variant

ax88179:
- max_mtu = 4088

cdc_ncm:
- max_mtu from hardware

cdc-phonet:
- min_mtu = 6, max_mtu = 65541

sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
  usbnet_change_mtu, but if we set max_mtu to let the network core handle
  the range check, then we can simply call usbnet_change_mtu directly

smsc75xx:
- max_mtu = 9000

CC: netdev@vger.kernel.org
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: Hayes Wang <hayeswang@realtek.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.

acenic:
- min_mtu = 0, max_mtu = 9000

amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu

amd/xgbe:
- min_mtu = 0, max_mtu = 9000

sb1250:
- min_mtu = 0, max_mtu = 1518

cxgb3:
- min_mtu = 81, max_mtu = 65535

cxgb4:
- min_mtu = 81, max_mtu = 9600

cxgb4vf:
- min_mtu = 81, max_mtu = 65535

benet:
- min_mtu = 256, max_mtu = 9000

ibmveth:
- min_mtu = 68, max_mtu = 65535

ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu

jme:
- min_mtu = 1280, max_mtu = 9202

mv643xx_eth:
- min_mtu = 64, max_mtu = 9500

mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
  checks in the respective switch drivers' ndo_change_mtu functions

ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500

netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)

qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
  rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
  the value is 1500 or 9000

qualcomm/emac:
- min_mtu = 46, max_mtu = 9194

xilinx_axienet:
- min_mtu = 64, max_mtu = 9000

Fixes: 61e84623 ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix typo in parameter description.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in mtk_start_xmit()
which can be called from hard irq context (netpoll) and from
other contexts. mtk_start_xmit() only frees skbs that it has
dropped.

This is detected by Coccinelle semantic patch.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in dwceqos_start_xmit()
which can be called from hard irq context (netpoll) and from
other contexts. dwceqos_start_xmit() only frees skbs that it has
dropped.

This is detected by Coccinelle semantic patch.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AQR106 and AQR107 can use the existing driver.
Signed-off-by: NShaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_prepare, clk_enable and their counterparts (at least the common clk
ones, but also most others) do check for the clk being NULL anyhow (and
return 0 then), so there is no gain when the caller checks, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch isolating the u16 writes for pxa assumed all machine_is_*()
calls were removed, and therefore removed the mach-types.h include which
provided them.

Unfortunately 2 machine_is_*() remained in smc91x.c file including
smc91x.h from which the include was removed, triggering the error:
 drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_drv_probe’:
 drivers/net/ethernet/smsc/smc91x.c:2380:2: error: implicit declaration
 of function ‘machine_is_assabet’
 [-Werror=implicit-function-declaration]
	if (machine_is_assabet() && machine_has_neponset())

This adds back the wrongly removed include.

Fixes: d09d747a ("net: smc91x: isolate u16 writes alignment workaround")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some applications want to tune the size of the macb rx/tx ring buffers.
The ethtool set_ringparam function is the standard way of doing it.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macb driver hardcoded the tx/rx ring sizes. This made it
impossible to change the sizes at run time.

Add tx_ring_size, and rx_ring_size variables to macb object, which
are initilized with default vales during macb_init. Change all
references to RX_RING_SIZE and TX_RING_SIZE to their respective
replacements.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in arc_emac_tx()
which can be called from hard irq context (netpoll) and from
other contexts. arc_emac_tx() only frees skbs that it has
dropped.

This is detected by Coccinelle semantic patch.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a private copy of struct net_device_stats in struct
fs_enet_private, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The memory return by kzalloc() has already be set to zero, so
remove useless memset(0).
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/dsa/mv88e6xxx/chip.c:2866:5: warning:
 symbol 'mv88e6xxx_g1_set_switch_mac' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the following four products of Lenovo and sort the order of the list.

	VID		PID
	0x17ef		0x3062
	0x17ef		0x3069
	0x17ef		0x720c
	0x17ef		0x7214
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For device-tree builds, platforms such as mainstone, idp and stargate2
must have their u16 writes all aligned on 32 bit boundaries. This is
already enabled in platform data builds, and this patch adds it to
device-tree builds.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Writes to u16 has a special handling on 3 PXA platforms, where the
hardware wiring forces these writes to be u32 aligned.

This patch isolates this handling for PXA platforms as before, but
enables this "workaround" to be set up dynamically, which will be the
case in device-tree build types.

This patch was tested on 2 PXA platforms : mainstone, which relies on
the workaround, and lubbock, which doesn't.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 61e84623 ("net: centralize net_device min/max MTU checking")
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.

This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.

For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: NJosh Cartwright <josh.cartwright@ni.com>
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: NZach Brown <zach.brown@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: phy: Create phy_supported_speeds function which lists speeds currently supported by a phydevice

phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During phy state machine state transitions some set of actions should
occur whenever the link state changes. These actions should be
encapsulated into a single function

This patch adds the phy_adjust_link function, which is called whenever
phydev->adjust_link would have been called before. Actions that should
occur whenever the phy link is adjusted can now be added to the
phy_adjust_link function.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding led support for phy causes namespace conflicts for some
phy drivers.

The marvel skge driver declared an enum for representing the states of
Link LED Register. The enum contained constant LED_OFF which conflicted
with declartation found in linux/leds.h.
LED_OFF changed to LED_REG_OFF
Also changed LED_ON to LED_REG_ON to avoid possible future conflict and
for consistency.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert rocker to the new dev walk API. This is just a code conversion;
no functional change is intended.

v2
- removed typecast of data
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert mlxsw users to new dev walk API. This is just a code conversion;
no functional change is intended.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert ixgbe users to new dev walk API. This is just a code conversion;
no functional change is intended.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert alb_send_learning_packets and bond_has_this_ip to use the new
netdev_walk_all_upper_dev_rcu API. In both cases this is just a code
conversion; no functional change is intended.

v2
- removed typecast of data and simplified bond_upper_dev_walk
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

et131x: min_mtu 64, max_mtu 9216

altera_tse: min_mtu 64, max_mtu 1500

amd8111e: min_mtu 60, max_mtu 9000

bnad: min_mtu 46, max_mtu 9000

macb: min_mtu 68, max_mtu 1500 or 10240 depending on hardware capability

xgmac: min_mtu 46, max_mtu 9000

cxgb2: min_mtu 68, max_mtu 9582 (pm3393) or 9600 (vsc7326)

enic: min_mtu 68, max_mtu 9000

gianfar: min_mtu 50, max_mu 9586

hns_enet: min_mtu 68, max_mtu 9578 (v1) or 9706 (v2)

ksz884x: min_mtu 60, max_mtu 1894

myri10ge: min_mtu 68, max_mtu 9000

natsemi: min_mtu 64, max_mtu 2024

nfp: min_mtu 68, max_mtu hardware-specific

forcedeth: min_mtu 64, max_mtu 1500 or 9100, depending on hardware

pch_gbe: min_mtu 46, max_mtu 10300

pasemi_mac: min_mtu 64, max_mtu 9000

qcaspi: min_mtu 46, max_mtu 1500
- remove qcaspi_netdev_change_mtu as it is now redundant

rocker: min_mtu 68, max_mtu 9000

sxgbe: min_mtu 68, max_mtu 9000

stmmac: min_mtu 46, max_mtu depends on hardware

tehuti: min_mtu 60, max_mtu 16384
- driver had no max mtu checking, but product docs say 16k jumbo packets
  are supported by the hardware

netcp: min_mtu 68, max_mtu 9486
- remove netcp_ndo_change_mtu as it is now redundant

via-velocity: min_mtu 64, max_mtu 9000

octeon: min_mtu 46, max_mtu 65370

CC: netdev@vger.kernel.org
CC: Mark Einon <mark.einon@gmail.com>
CC: Vince Bridgers <vbridger@opensource.altera.com>
CC: Rasesh Mody <rasesh.mody@qlogic.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC:  Christian Benvenuti <benve@cisco.com>
CC: Sujith Sankar <ssujith@cisco.com>
CC: Govindarajulu Varadarajan <_govind@gmx.com>
CC: Neel Patel <neepatel@cisco.com>
CC: Claudiu Manoil <claudiu.manoil@freescale.com>
CC: Yisen Zhuang <yisen.zhuang@huawei.com>
CC: Salil Mehta <salil.mehta@huawei.com>
CC: Hyong-Youb Kim <hykim@myri.com>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Olof Johansson <olof@lixom.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Byungho An <bh74.an@samsung.com>
CC: Girish K S <ks.giri@samsung.com>
CC: Vipul Pandya <vipul.pandya@samsung.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Alexandre Torgue <alexandre.torgue@st.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Wingman Kwok <w-kwok2@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gelic_net: min_mtu 64, max_mtu 1518
- remove gelic_net_change_mtu now that it is redundant

spidernet: min_Mtu 64, max_mtu 2294
- remove spiter_net_change_mtu now that it is redundant

CC: netdev@vger.kernel.org
CC: Geoff Levand <geoff@infradead.org>
CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tilegx: min_mtu 68, max_mtu 1500 or 9000, depending on modparam
- remove tile_net_change_mtu now that it is fully redundant

tilepro: min_mtu 68, max_mtu 1500
- hardware supports jumbo packets up to 10226, but it's not implemented or
  tested yet, according to code comments

CC: netdev@vger.kernel.org
CC: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ehea: min_mtu 68, max_mtu 9022
- remove ehea_change_mtu, it's now redundant

emac: min_mtu 46, max_mtu 1500 or whatever gets read from OF

CC: netdev@vger.kernel.org
CC: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

liquidio: min_mtu 68, max_mtu 16000

thunder: min_mtu 64, max_mtu 9200

CC: netdev@vger.kernel.org
CC: Sunil Goutham <sgoutham@cavium.com>
CC: Robert Richter <rric@kernel.org>
CC: Derek Chickles <derek.chickles@caviumnetworks.com>
CC: Satanand Burla <satananda.burla@caviumnetworks.com>
CC: Felix Manlunas <felix.manlunas@caviumnetworks.com>
CC: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

s2io: min_mtu 46, max_mtu 9600

vxge: min_mtu 68, max_mtu 9600

CC: netdev@vger.kernel.org
CC: Jon Mason <jdmason@kudzu.us>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dl2k: min_mtu 68, max_mtu 1536 or 8000, depending on hardware
- Removed change_mtu, does nothing productive anymore

sundance: min_mtu 68, max_mtu 8191

CC: netdev@vger.kernel.org
CC: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cassini: min_mtu 60, max_mtu 9000

niu: min_mtu 68, max_mtu 9216

sungem: min_mtu 68, max_mtu 1500 (comments say jumbo mode is broken)

sunvnet: min_mtu 68, max_mtu 65535
- removed sunvnet_change_mut_common as it does nothing now

CC: netdev@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

8139cp: min_mtu 60, max_mtu 4096

8139too: min_mtu 68, max_mtu 1770

r8169: min_mtu 60, max_mtu depends on chipset, 1500 to 9k-ish

CC: netdev@vger.kernel.org
CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h

qlcnic: min_mtu 68, max_mtu 9600

CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4: min_mtu 46, max_mtu depends on hardware

mlx5: min_mtu 68, max_mtu depends on hardware

CC: netdev@vger.kernel.org
CC: Tariq Toukan <tariqt@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>