Jeff Kirsher says:

====================
This series contains updates to e1000, igb, ixgbe and ixgbevf.

Hong Zhiguo provides a fix for e1000 where tx_ring and adapter->tx_ring
are already of type "struct e1000_tx_ring" so no need to divide by
e1000_tx_ring size in the idx calculation.

Emil provides a fix for ixgbevf to remove a redundant workaround related
to header split and a fix for ixgbe to resolve an issue where the MTA table
can be cleared when the interface is reset while in promisc mode.

Todd provides a fix for igb to prevent ethtool from writing to the iNVM
in i210/i211 devices.  This issue was reported by Marek Vasut <marex@denx.de>.

Anton Blanchard provides a fix for ixgbe to reduce memory consumption
with larger page sizes, seen on PPC.

Don provides a cleanup in ixgbe to replace the IXGBE_DESC_UNUSED macro with
the inline function ixgbevf_desc_unused() to make the logic a bit more
readable.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
A single fix by Alexandre Rames for the recent changes to TSO.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resolves an issue where the MTA table can be cleared when the
interface is reset while in promisc mode. As result IPv6 traffic between
VFs will be interrupted.

This patch makes the update of the MTA table unconditional to avoid the
inconsistent clearing on reset.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch just replaces the IXGBE_DESC_UNUSED macro with a like named
inline function ixgbevf_desc_unused. The inline function makes the logic
a bit more readable.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe driver allocates pages for its receive rings. It currently
uses 512 pages, regardless of page size. During receive handling it
adds the unused part of the page back into the rx ring, avoiding the
need for a new allocation.

On a ppc64 box with 64 threads and 64kB pages, we end up with
512 entries * 64 rx queues * 64kB = 2GB memory used. Even more of a
concern is that we use up 2GB of IOMMU space in order to map all this
memory.

The driver makes a number of decisions based on if PAGE_SIZE is less
than 8kB, so use this as the breakpoint and only allocate 128 entries
on 8kB or larger page sizes.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't let ethtool try to write to iNVM in i210/i211.

This fixes an issue seen by Marek Vasut.
Reported-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes a workaround related to header split, which is redundant
because the driver does not support splitting packet headers on Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

tx_ring and adapter->tx_ring are already of type "struct
e1000_tx_ring *"
Signed-off-by: NHong Zhiguo <zhiguohong@tencent.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When using firmware assisted TSO, we use a single DMA mapping for
the linear area of a TSO skb.

We still have to segment the super-packet and insert a descriptor
containing the original headers before each segment of payload, so we
can unmap the linear area only after the last segment is completed.
The unmapping information for the linear area is therefore associated
with the last header descriptor.

We calculate the DMA address to unmap from using the map length and
the invariant that the end of the DMA mapping matches the end of
the data referenced by the last descriptor.  But this invariant is
broken when there is TCP payload in the linear area.

Fix this by adding and using an explicit dma_offset field.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Alexander Aring says:

====================
This patch series cleanup the 6LoWPAN header creation and extend the use
of skb_*_header functions.

Patch 2/4 fix issues of parsing the mac header. The ieee802.15.4 header
has a dynamic size which depends on frame control bits. This patch replaces the
static mac header len calculation with a dynamic one.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch drops the direct memcpy on skb and uses the right skb
memcpy functions. Also remove an unnecessary check if plen is non zero.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Reviewed-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is necessary to access network header with the skb_network_header
function instead of calculate the position with mac_len, etc.
Do the same for the transport header, when we replace the IPv6 header
with the 6LoWPAN header.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Acked-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the mac header length while creating the 802.15.4 mac header.

Drop the function for recalculate mac header length in upper layers
which was static and works for intra pan communication only.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Reviewed-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On receiving side we don't need to set any headers in skb because the
6LoWPAN layer do not access it. Currently these values will set twice
after calling netif_rx.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Reviewed-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After reading the function rt6_check_neigh(), we can
know that the RT6_NUD_FAIL_SOFT can be returned only
when the IS_ENABLE(CONFIG_IPV6_ROUTER_PREF) is false.
so in function find_match(), there is no need to execute
the statement !IS_ENABLED(CONFIG_IPV6_ROUTER_PREF).
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is inspired by checkpatch.
Signed-off-by: NWeilong Chen <chenweilong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Copying whole packets with skb_copy_from_linear_data_offset is a pretty
bad idea. CPU was spending time in __copy_user_common and network
performance was lower. With the new solution iperf-measured speed
increased from 116Mb/s to 134Mb/s.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The message dispatching part of tipc_recv_msg() is wrapped layers of
while/if/if/switch, causing out-of-control indentation and does not
look very good. We reduce two indentation levels by separating the
message dispatching from the blocks that checks link state and
sequence numbers, allowing longer function and arg names to be
consistently indented without wrapping. Additionally we also rename
"cont" label to "discard" and add one new label called "unlock_discard"
to make code clearer. In all, these are cosmetic changes that do not
alter the operation of TIPC in any way.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Cc: David Laight <david.laight@aculab.com>
Cc: Andreas Bofjäll <andreas.bofjall@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address(). While at it, reorganize checking so it matches checks in
other drivers.
Signed-off-by: NLuka Perkov <luka@openwrt.org>
CC: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address().
Signed-off-by: NLuka Perkov <luka@openwrt.org>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address().
Signed-off-by: NLuka Perkov <luka@openwrt.org>
Acked-by: NDavid Daney <david.daney@cavium.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fast Open currently has a fall back feature to address SYN-data being
dropped but it requires the middle-box to pass on regular SYN retry
after SYN-data. This is implemented in commit aab48743 ("net-tcp:
Fast Open client - detecting SYN-data drops")

However some NAT boxes will drop all subsequent packets after first
SYN-data and blackholes the entire connections.  An example is in
commit 356d7d88 "netfilter: nf_conntrack: fix tcp_in_window for Fast
Open".

The sender should note such incidents and fall back to use the regular
TCP handshake on subsequent attempts temporarily as well: after the
second SYN timeouts the original Fast Open SYN is most likely lost.
When such an event recurs Fast Open is disabled based on the number of
recurrences exponentially.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to vxlan, net, ixgbe, ixgbevf, and i40e.

Joseph provides a single patch against vxlan which removes the burden
from the NIC drivers to check if the vxlan driver is enabled in the
kernel and also makes available the vxlan headrooms to the drivers.

Jacob provides majority of the patches, with patches against net, ixgbe
and ixgbevf.  His net patch adds might_sleep() call to napi_disable so
that every use of napi_disable during atomic context will be visible.
Then Jacob provides a patch to fix qv_lock_napi call in
ixgbe_napi_disable_all.  The other ixgbe patches cleanup
ixgbe_check_minimum_link function to correctly show that there are some
minor loss of encoding, even though we don't calculate it and remove
unnecessary duplication of PCIe bandwidth display.  Lastly, Jacob
provides 4 patches against ixgbevf to add ixgbevf_rx_skb in line with
how ixgbe handles the variations on how packets can be received, adds
support in order to track how many packets were cleaned during busy poll
as part of the extended statistics.

Wei Yongjun provides a fix for i40e to return -ENOMEN in the memory
allocation error handling case instead of returning 0, as done
elsewhere in this function.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amend the documentation in the mvmdio driver to note the fact
that it is now used by both the mvneta and mv643xx_eth drivers.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make only a single call to mutex_unlock in orion_mdio_write.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace manual poll of MVMDIO_SMI_READ_VALID with a call to
orion_mdio_wait_ready.  This ensures a consistent timeout,
eliminates a busy loop, and allows for use of interrupts on
systems that support them.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amend orion_mdio_wait_ready so that the same timeout is used when
polling or using wait_event_timeout.  Set the timeout to 1ms.

Replace udelay with usleep_range to avoid a busy loop, and set the
polling interval range as 45us to 55us, so that the first sleep
will be enough in almost all cases.

Generate the same log message at timeout when polling or using
wait_event_timeout.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function needn't to be public, so to make it as static.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interface type, which is being traced by "struct be_adapter::
if_type", isn't used currently. So we can remove that safely
according to Sathya's comments.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

Convert printks to pr_<level>.

Consolidate multiple printks into a single printk to avoid
any possible dmesg interleaving.  Add a default "event" msg
in case the listed types are ever expanded.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This work contains a lightweight BPF-based traffic classifier that can
serve as a flexible alternative to ematch-based tree classification, i.e.
now that BPF filter engine can also be JITed in the kernel. Naturally, tc
actions and policies are supported as well with cls_bpf. Multiple BPF
programs/filter can be attached for a class, or they can just as well be
written within a single BPF program, that's really up to the user how he
wishes to run/optimize the code, e.g. also for inversion of verdicts etc.
The notion of a BPF program's return/exit codes is being kept as follows:

     0: No match
    -1: Select classid given in "tc filter ..." command
  else: flowid, overwrite the default one

As a minimal usage example with iproute2, we use a 3 band prio root qdisc
on a router with sfq each as leave, and assign ssh and icmp bpf-based
filters to band 1, http traffic to band 2 and the rest to band 3. For the
first two bands we load the bytecode from a file, in the 2nd we load it
inline as an example:

echo 1 > /proc/sys/net/core/bpf_jit_enable

tc qdisc del dev em1 root
tc qdisc add dev em1 root handle 1: prio bands 3 priomap 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

tc qdisc add dev em1 parent 1:1 sfq perturb 16
tc qdisc add dev em1 parent 1:2 sfq perturb 16
tc qdisc add dev em1 parent 1:3 sfq perturb 16

tc filter add dev em1 parent 1: bpf run bytecode-file /etc/tc/ssh.bpf flowid 1:1
tc filter add dev em1 parent 1: bpf run bytecode-file /etc/tc/icmp.bpf flowid 1:1
tc filter add dev em1 parent 1: bpf run bytecode-file /etc/tc/http.bpf flowid 1:2
tc filter add dev em1 parent 1: bpf run bytecode "`bpfc -f tc -i misc.ops`" flowid 1:3

BPF programs can be easily created and passed to tc, either as inline
'bytecode' or 'bytecode-file'. There are a couple of front-ends that can
compile opcodes, for example:

1) People familiar with tcpdump-like filters:

   tcpdump -iem1 -ddd port 22 | tr '\n' ',' > /etc/tc/ssh.bpf

2) People that want to low-level program their filters or use BPF
   extensions that lack support by libpcap's compiler:

   bpfc -f tc -i ssh.ops > /etc/tc/ssh.bpf

   ssh.ops example code:
   ldh [12]
   jne #0x800, drop
   ldb [23]
   jneq #6, drop
   ldh [20]
   jset #0x1fff, drop
   ldxb 4 * ([14] & 0xf)
   ldh [%x + 14]
   jeq #0x16, pass
   ldh [%x + 16]
   jne #0x16, drop
   pass: ret #-1
   drop: ret #0

It was chosen to load bytecode into tc, since the reverse operation,
tc filter list dev em1, is then able to show the exact commands again.
Possible follow-up work could also include a small expression compiler
for iproute2. Tested with the help of bmon. This idea came up during
the Netfilter Workshop 2013 in Copenhagen. Also thanks to feedback from
Eric Dumazet!
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cleans code a bit and will be useful when allocating buffers in
other places (like RX path, to avoid skb_copy_from_linear_data_offset).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return -ENOMEM in the memory alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the need to keep a zero_base variable in the adapter
structure. Now we just use two different macros to set the non-zero and
zero base. This adds to readability and shortens some of the structure
initialization under 80 columns. The gathering of status for ethtool was
slightly modified to again better fit into 80 columns and become a bit
more readable.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the extended statistics similar to the ixgbe driver. These
statistics keep track of how often the busy polling yields, as well as how many
packets are cleaned or missed by the polling routine.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables CONFIG_NET_RX_BUSY_POLL support in the VF code. This enables
sockets which have enabled the SO_BUSY_POLL socket option to use the
ndo_busy_poll_recv operation which could result in lower latency, at the cost
of higher CPU utilization, and increased power usage. This support is similar
to how the ixgbe driver works.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rather than return true/false indicating whether there was budget left, return
the total packets cleaned. This currently has no use, but will be used in a
following patch which enables CONFIG_NET_RX_BUSY_POLL support in order to track
how many packets were cleaned during the busy poll as part of the extended
statistics.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds ixgbevf_rx_skb in line with how ixgbe handles the variations on
how packets can be received. It will be extended in a following patch for
CONFIG_NET_RX_BUSY_POLL support.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the unnecessary display of PCIe bandwidth twice. Since the
ixgbe_check_minimum_link does a better job, and ensures accurate detection on
even complex chains, this older check is no longer necessary.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the ixgbe_check_minimum_link function to correctly show that
there is some minor loss of encoding, even though we don't calculate it in the
max GT/s equation. It is small enough to not bother, but is better to report it
than not.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>