This patch adds the ethtool callbacks necessary to change the rss
indirection table from userspace.  Should the number of interrupts
change (e.g.  across a close / open call, or through a reset) and
any one of the indirection table values fall out-of-range, the driver
will reset the indirection table to a default layout.

[Integrated many suggestions made by Ben Hutchings.]

Changes since v3

* Removed TG3_FLAG_SUPPORT_MSIX checks at the start of
  tg3_get_rxfh_indir() and tg3_set_rxfh_indir().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2-mips-06-6.2.3 and bnx2-mips-09-6.2.1.b

New firmware fixes iSCSI problems with some LeftHand targets that don't
set TTT=0xffffffff for Data-In according to spec.  Firmware generates
exception warnings for this condition and becomes very slow.  This is
fixed by suppressing these warnings when using default error mask.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer does not have HW registers to indicate the EQ causing the INTx
interrupt. As a result EQE entries of one EQ may be consumed when interrupt
is caused by another EQ. Fix this by arming CQs at the end of NAPI poll
routine to regenerate the EQEs.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVinson Lee <vlee@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 5c3ddec7.

S390 qeth driver actually still uses the setup ops.
Reported-by: NFrank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The communication channel is HW interface from PF point of view
So the command return status should be stored as HW error code
and only then translated to errno values.
Reporetd-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is always called from irq context, changing the call
to spin_lock().
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Solves an issue where we tried to free the same page twice after
the port has been opened and closed.
Signed-off-by: NAlexander Guller <alexg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ConnectX3 devices, we allow link sensing only if FW explicitly
reported it supports the feature.
For older versions (ConnectX1 and 2), if the card supports both link layer types
(Ethenet and Infiniband), link sensing is supported.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

"result" isn't used.  We ignore errors here because there is not much we
can do about them.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: NIgor Maravić <igorm@etf.rs>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: NIgor Maravić <igorm@etf.rs>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: NIgor Maravić <igorm@etf.rs>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: NIgor Maravić <igorm@etf.rs>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In control path, its better to use GFP_KERNEL allocations where
possible.

Before taking qdisc spinlock, we preallocate memory just in case we'll
need it in gred_change_vq()

This is a followup to commit 3f1e6d3f (sch_gred: should not use
GFP_KERNEL while holding a spinlock)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGlauber Costa <glommer@parallels.com>
CC: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can't scan the proto_list to initialize sock cgroups, as it
holds a rwlock, and we also want to keep the code generic enough to
avoid calling the initialization functions of protocols directly,

Convert proto_list_lock into a mutex, so we can sleep and do the
necessary allocations. This lock is seldom taken, so there shouldn't
be any performance penalties associated with that
Signed-off-by: NGlauber Costa <glommer@parallels.com>
CC: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a compile error that occurs when the driver
is compile into the kernel and not as a module.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I didn't resolve the merge properly during the last pull of the net
tree into net-next.

The code in the final resolution should set flags to TT_CLIENT_ROAM
not TT_CLIENT_PENDING.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation.  Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.

In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new ethtool operation (get_rxfh_indir_size) to get the
indirectional table size.  Use this to validate the user buffer size
before calling get_rxfh_indir or set_rxfh_indir.  Use get_rxnfc to get
the number of RX rings, and validate the contents of the new
indirection table before calling set_rxfh_indir.  Remove this
validation from drivers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to find out the device's RX flow hash table size, ethtool
initially uses ETHTOOL_GRXFHINDIR with a buffer size of zero.  This
must be supported, but it is not necessary to support any other user
buffer size less than the device table size.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When establishing a unix connection on stream sockets the
server end receives an skb with socket in its receive queue.

Report who is waiting for these ends to be accepted for
listening sockets via NLA.

There's a lokcing issue with this -- the unix sk state lock is
required to access the peer, and it is taken under the listening
sk's queue lock. Strictly speaking the queue lock should be taken
inside the state lock, but since in this case these two sockets
are different it shouldn't lead to deadlock.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report the peer socket inode ID as NLA. With this it's finally
possible to find out the other end of an interesting unix connection.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Actually, the socket path if it's not anonymous doesn't give
a clue to which file the socket is bound to. Even if the path
is absolute, it can be unlinked and then new socket can be
bound to it.

With this NLA it's possible to check which file a particular
socket is really bound to.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report the sun_path when requested as NLA. With leading '\0' if
present but without the leading AF_UNIX bits.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The socket inode is used as a key for lookup. This is effectively
the only really unique ID of a unix socket, but using this for
search currently has one problem -- it is O(number of sockets) :(

Does it worth fixing this lookup or inventing some other ID for
unix sockets?
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Walk the unix sockets table and fill the core response structure,
which includes type, state and inode.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Includes basic module_init/_exit functionality, dump/get_exact stubs
and declares the basic API structures for request and response.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sk address is used as a cookie between dump/get_exact calls.
It will be required for unix socket sdumping, so move it from
inet_diag to sock_diag.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've made a mistake when fixing the sock_/inet_diag aliases :(

1. The sock_diag layer should request the family-based alias,
   not just the IPPROTO_IP one;
2. The inet_diag layer should request for AF_INET+protocol alias,
   not just the protocol one.

Thus fix this.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should belong to sock_diag, not inet_diag.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>