- 17 9月, 2015 3 次提交
-
-
由 Kuba Pawlak 提交于
SCO packet reassembler may have a fragment of SCO packet, from previous connection, cached and not removed when SCO connection is ended. Packets from new SCO connection are then going to be attached to that fragment, creating an invalid SCO packets. Controllers like Intel's WilkinsPeak are always fragmenting SCO packet into 3 parts (#1, #2, #3). Packet #1 contains SCO header and audio data, others just audio data. if there is a fragment cached from previous connection, i.e. #1, first SCO packet from new connection is going to be attached to it creating packet consisting of fragments #1-#1-#2. This will be forwarded to upper layers. After that, fragment #3 is going to be used as a starting point for another SCO packet. It does not contain a SCO header, but the code expects it, casts a SCO header structure on it, and reads whatever audio data happens to be there as SCO packet length and handle. From that point on, we are assembling random data into SCO packets. Usually it recovers quickly as initial audio data contains mostly zeros (muted stream), but setups of over 4 seconds were observed. Issue manifests itself by printing on the console: Bluetooth: hci0 SCO packet for unknown connection handle 48 Bluetooth: hci0 SCO packet for unknown connection handle 2560 Bluetooth: hci0 SCO packet for unknown connection handle 12288 It may also show random handles if audio data was non-zeroed. Hcidump shows SCO packets with random length and handles. Few messages with handle 0 at connection creation are OK for some controllers (like WilkinsPeak), as there are SCO packets with zeroed handle at the beginning (possible controller bug). Few of such messages at connection end, with a handle looking sane (around 256, 512, 768 ...) is also OK, as these are last SCO packets that were assembled and sent up, before connection was ended, but were not handled in time. This issue may still manifest itself on WilkinsPeak as it sometimes, at SCO connection creation, does not send third fragment of first SCO packet (#1-#2-#1-#2-#3...). This is a firmware bug and this patch does not address it. Signed-off-by: NKuba Pawlak <kubax.t.pawlak@intel.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Loic Poulain 提交于
btintel_load_ddc_config is now part of btintel. Signed-off-by: NLoic Poulain <loic.poulain@intel.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Johan Hedberg 提交于
Controllers claiming to be CSR with LMP subversion 0x0c5c don't actually seem to be authentic CSR controllers. They also don't have their USB bcdDevice value matching the LMP subversion like all other CSR controllers: HCI: > HCI Event: Command Complete (0x0e) plen 12 Read Local Version Information (0x04|0x0001) ncmd 1 Status: Success (0x00) HCI version: Bluetooth 2.0 (0x03) - Revision 3164 (0x0c5c) LMP version: Bluetooth 2.0 (0x03) - Subversion 3164 (0x0c5c) Manufacturer: Cambridge Silicon Radio (10) USB: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=16 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev= 1.34 C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms These controllers also have the HCI_Read_Stored_Link_Key command broken so it's important the right quirk is set for them. Reported-and-tested-by: NRhobison Alves Pereira <rhobison@hotmail.com> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 29 8月, 2015 1 次提交
-
-
由 Minjune Kim 提交于
Signed-off-by: NMinjune Kim <infinite.minjune.kim@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 16 8月, 2015 1 次提交
-
-
由 Peter Poklop 提交于
This patch enables quirk handling for Silicon Wave based devices and fixes kernel bug with id 42985. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0c10 ProdID=0000 Rev=15.00 S: Manufacturer=SiW S: Product=SiW S: SerialNumber=340A05F61100 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NPeter Poklop <peter.poklop@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 30 7月, 2015 1 次提交
-
-
由 Daniel Drake 提交于
btusb currently has a generic match on USB device descriptors: { USB_DEVICE_INFO(0xe0, 0x01, 0x01) }, However, http://www.usb.org/developers/defined_class states: Base Class E0h (Wireless Controller) This base class is defined for devices that are Wireless controllers. Values not shown in the table below are reserved. These class codes are to be used in Interface Descriptors, with the exception of the Bluetooth class code which can also be used in a Device Descriptor. Add a match on the interface descriptors accordingly. This fixes compatibility with the RTL8723AU device shown below. This device conforms to the USB Interface Association Descriptor specification, which requires the device to have class ef/02/01. The extra IAD descriptor then specifies that interfaces 0 and 1 belong to the same function/driver, which is true. Provided that the Bluetooth device class spec accepts use of the IAD, I imagine that technically, all btusb devices should be configured like this. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=0724 Rev= 2.00 S: Manufacturer=Realtek S: Product=802.11n WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=500us Signed-off-by: NDaniel Drake <drake@endlessm.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 23 7月, 2015 3 次提交
-
-
由 Marcel Holtmann 提交于
The Intel version information is shared between USB and UART drivers and with that move it into a generic function of the Intel module. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The Intel Secure Send command is used the same in USB and UART drivers and with that move a generic version into the Intel module. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The Intel specific Bluetooth module provides now an exported function for the hardware error. Use that instead of duplicating it inside the driver. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
- 19 6月, 2015 1 次提交
-
-
由 Dmitry Tunin 提交于
BugLink: https://bugs.launchpad.net/bugs/1394368 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300d Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
-
- 17 6月, 2015 1 次提交
-
-
由 Tedd Ho-Jeong An 提交于
This patch adds the routine to apply the DDC parameter from device specific ddc file. Once the device is rest to operational mode, optionally, it can download the device specific configration (DDC) parameters before the BlueZ starts the stack initialization. It opens the DDC file based on HW_VARIANT and DEV_REVISION and send ID/Value with HCI_Intel_Write_DDC command. Format of DDC file DDC file contains one or more number of DDC structure. DDC Structure It has 'Length' field of one octet, DDC 'ID' field of two octets followed by the array of DDC 'Value' that gives the value of parameters itself. 'Length' contains the length of DDC 'ID' and DDC 'Value'. +------------+----------+ | Size(byte) | Name | +------------+----------+ | 1 | Length | +------------+----------+ | 2 | ID | +------------+----------+ | Length - 2 | Value | +------------+----------+ Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 09 6月, 2015 1 次提交
-
-
由 Marcel Holtmann 提交于
This patch fixes the command length alignment issue for Intel Bluetooth 8260. The length of parameters in the firmware downloading command must be multiplication of 4. If not, the command must append Intel_NOP command with extra parameters, zeros, at the end, and the firmware file is already included Intel_NOP command for alignment. This patch checks the next command and if the next command is Intel_NOP command, it reads the Intel_NOP command and send them together. For example, if the data from the firmware file looks like this: 8E FC 03 11 22 33 02 FC 03 00 00 00 Previously, btusb sends two commands: 09 FC 06 8E FC 03 11 22 33 09 FC 06 02 FC 03 00 00 00 This won't work because the length of parameters are 6 which violates the 4 byte alignment. This patch will append them together and send as one command: 09 FC 0C 8E FC 03 11 22 33 02 FC 03 00 00 00 Based on previous work from Tedd Ho-Jeong An <tedd.an@intel.com> Reported-by: NTedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Tested-by: NTedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
-
- 08 6月, 2015 4 次提交
-
-
由 Aleksei Volkov 提交于
That patch corrects the typo in usb vendor id for Roper Class 1 Bluetooth Dongle. Problem with typo is present since 4.0 kernel. Content /sys/kernel/debug/usb/devices for these dongle: T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1310 ProdID=0001 Rev=15.00 S: Manufacturer=SiW S: Product=SiW S: SerialNumber=E7BB050D0B00 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NAleksei Volkov <info@dv2c.ru> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org # 4.0.x
-
由 Marcel Holtmann 提交于
The btusb_read_local_version function has only a single user and with that just move its functionality in place where it belongs. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The __hci_cmd_sync function already handles the command status and command complete errors. No need to check the status field again. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The SKB returned from the Intel specific version information command is missing a kfree_skb. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
-
- 07 6月, 2015 2 次提交
-
-
由 Dmitry Tunin 提交于
BugLink: https://bugs.launchpad.net/bugs/1427680 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3474 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
-
由 Dmitry Tunin 提交于
BugLink: https://bugs.launchpad.net/bugs/1462614 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=06 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e076 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
-
- 26 5月, 2015 3 次提交
-
-
由 Daniel Drake 提交于
Realtek btusb devices don't currently work after suspend/resume because the updated firmware is quietly lost - the USB hub doesn't notice any status change upon resume, but some kind of reset has definitely happened as the LMP subversion has reverted to its original value. Set the reset_resume flag to trigger probe and upload the new firmware again. Like the vendor code, I assume this is not needed when the device is selected as a wakeup source and hence will retain power during suspend. On the 2 products I have to hand, when trying this configuration the hardware seems unable to keep the device powered up during suspend. The USB hub then detects a status change on resume and does a reset, so we do not end up in broken state. Signed-off-by: NDaniel Drake <drake@endlessm.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Shailendra Verma 提交于
The reset is a bool type variable. So assigning true to reset instead of 1. Signed-off-by: NShailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Chan-yeol Park 提交于
The previous commit(3267c884) missed QCA61x4 ROME v2.0 info on Samsung so its BT is not activated and the below message is shown. [ 8.009638] usb 1-1: New USB device found, idVendor=0cf3, idProduct=e300 [ 8.012637] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 8.102901] Bluetooth: hci0: don't support firmware rome 0x200 This patch adds QCA61x4 ROME v2.0 info in qca_devices_table[], and is verified on Samsung with the firmware provided by Kim, Ben Young Tae <ytkim@qca.qualcomm.com>. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 15 5月, 2015 1 次提交
-
-
由 Frederic Danis 提交于
Remove test of command reply status as it is already performed by __hci_cmd_sync(). __hci_cmd_sync_ev() function already returns an error if it got a non-zero status either through a Command Complete or a Command Status event. For both of these events the status is collected up in the event handlers called by hci_event_packet() and then passed as the second parameter to req_complete_skb(). The req_complete_skb() callback in turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores the status in hdev->req_result. The hdev->req_result is then further converted through bt_to_errno() back in __hci_cmd_sync_ev(). Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 14 5月, 2015 4 次提交
-
-
由 Carlo Caione 提交于
As already done for btintel and btbcm export setup as separate function in a vendor-specific module to hold all the Realtek specific commands. Signed-off-by: NCarlo Caione <carlo@endlessm.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Dmitry Tunin 提交于
BugLink: https://bugs.launchpad.net/bugs/1449730 T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300f Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Wen-chien Jesse Sung 提交于
Device 0cf3:e007 is one of the QCA ROME family. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e007 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Wen-chien Jesse Sung 提交于
Device info in /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e006 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 30 4月, 2015 3 次提交
-
-
由 Dan Carpenter 提交于
The ">" should be ">=" so that we don't read past the end of the array. Fixes: 9d9a113e3695 ('Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A support') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Reviewed-by: NDaniel Drake <drake@endlessm.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Marcel Holtmann 提交于
ERROR: spaces required around that '<' (ctx:WxV) + if (err <0) ^ ERROR: code indent should use tabs where possible +^I^I^I^I sizeof(ver));$ Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Daniel Drake 提交于
Realtek ship a variety of bluetooth USB devices that identify themselves with standard USB Bluetooth device class values, but require a special driver to actually work. Without that driver, you never get any scan results. More recently however, Realtek appear to have wisened up and simply posted a firmware update that makes these devices comply with normal btusb protocols. The firmware needs to be uploaded on each boot. Based on Realtek code from https://github.com/lwfinger/rtl8723au_bt ('new' branch). This enables bluetooth support in the Gigabyte Brix GB-BXBT-2807 which has this RTL8723BE USB device: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3410 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms There is no change to the USB descriptor after firmware update, however the version read by HCI_OP_READ_LOCAL_VERSION changes from 0x8723 to 0x3083. This has also been tested on RTL8723AE and RTL8821AE. Support for RTL8761A has also been added, but that is untested. Signed-off-by: NDaniel Drake <drake@endlessm.com> Tested-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 09 4月, 2015 1 次提交
-
-
由 Marcel Holtmann 提交于
The Intel vendors events indicating firmware loading result and the bootup of the operational firmware are currently hardcoded byte comparisons. So intead of doing that, provide proper data structures and actually use them. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
- 08 4月, 2015 6 次提交
-
-
由 Marcel Holtmann 提交于
Since the Intel Bluetooth support has its own header, it makes sense to move all command structs into it. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The Bluetooth address handling for Intel devices is provided by a generic module now. Start using that module instead of relying it being included in the driver. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The version number is cosmetic, but pretty handy for debugging purposes and since the Broadcom protocol support is now optional, just increase it to indicate the difference. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The quirks for Broadcom devices can be set from the setup function and to keep the code simple, just move them into Broadcom support module. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
With the generic Broadcom Bluetooth support module, it is possible to turn support for firmware and patchram download into an optional feature. To keep backwards compatibility with previous kernel configurations, the new option defaults to enabled. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
由 Marcel Holtmann 提交于
The new Broadcom Bluetooth support module provides generic functionality for changing and checking the Bluetooth device address. Use these new features instead of keeping a duplicate in the driver. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
- 28 3月, 2015 1 次提交
-
-
由 Marcel Holtmann 提交于
For all modern Bluetooth USB devices from Broadcom it makes a lot more sense to use USB_VENDOR_AND_INTERFACE_INFO instead of manually adding USB_DEVICE for each one of them. There are already interface entries for these vendors and so just remove the duplicate device entries. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
- 23 3月, 2015 1 次提交
-
-
由 Marcel Holtmann 提交于
For the Apple Bluetooth devices that are Broadcom based, it makes sense to read the chip information. It is a single HCI command and might help gathering more information about these devices. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
- 21 3月, 2015 1 次提交
-
-
由 Marcel Holtmann 提交于
The Broadcom devices expose their chip id via Read Verbose Config Version Info command. While this information is not used at the moment, it might be useful for debugging purposes and so read it before patching the firmware. This makes it show up in dmesg and HCI traces taken for the system. Signed-off-by: NMarcel Holtmann <marcel@holtmann.org> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-
- 18 3月, 2015 1 次提交
-
-
由 Jakub Pawlowski 提交于
CSR controllers can do both LE scan and BR/EDR inquiry at once. Signed-off-by: NJakub Pawlowski <jpawlowski@google.com> Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
-