Teach the mcp23s08 driver about a curious feature of these chips: up to
four of them can share the same chipselect, with the SPI signals wired in
parallel, by matching two bits in the first protocol byte against two
address lines on the chip.

This is handled by three software changes:

  * Platform data now holds an array of per-chip structs, not
    just one chip's address and pullup configuration.

  * Probe() and remove() now use another level of structure,
    wrapping an instance of the original structure for each
    mcp23s08 chip sharing that chipselect.

  * The HAEN bit is set, so that the hardware address bits can no
    longer be ignored (boot firmware may not have enabled them).

The "one struct per chip" preserves the guts of the current code,
but platform_data will need minor changes.

    OLD:
	/* incorrect "slave" ID may not have mattered */
	.slave = 3,
	.pullups = BIT(3) | BIT(1) | BIT(0),

    NEW:
	/* slave address _must_ match chip's wiring */
	.chip[3] = {
		.is_present = true,
		.pullups = BIT(3) | BIT(1) | BIT(0),
	},

There's no change in how things _behave_ for spi_device nodes with a
single mcp23s08 chip.  New multi-chip configurations assign GPIOs in
sequence, without holes.  The spi_device just resembles a bigger
controller, but internally it has multiple gpio_chip instances.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a simple sysfs interface for GPIOs.

    /sys/class/gpio
    	/export ... asks the kernel to export a GPIO to userspace
    	/unexport ... to return a GPIO to the kernel
        /gpioN ... for each exported GPIO #N
	    /value ... always readable, writes fail for input GPIOs
	    /direction ... r/w as: in, out (default low); write high, low
	/gpiochipN ... for each gpiochip; #N is its first GPIO
	    /base ... (r/o) same as N
	    /label ... (r/o) descriptive, not necessarily unique
	    /ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)

GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.

Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:

  echo 23 > /sys/class/gpio/export
	... will gpio_request(23, "sysfs") and gpio_export(23);
	use /sys/class/gpio/gpio-23/direction to (re)configure it,
	when that GPIO can be used as both input and output.
  echo 23 > /sys/class/gpio/unexport
	... will gpio_free(23), when it was exported as above

The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO.  The additional I-space
footprint is about two thirds of the current size of gpiolib (!).  Since
no /dev node creation is involved, no "udev" support is needed.

Related changes:

  * This adds a device pointer to "struct gpio_chip".  When GPIO
    providers initialize that, sysfs gpio class devices become children of
    that device instead of being "virtual" devices.

  * The (few) gpio_chip providers which have such a device node have
    been updated.

  * Some gpio_chip drivers also needed to update their module "owner"
    field ...  for which missing kerneldoc was added.

  * Some gpio_chips don't support input GPIOs.  Those GPIOs are now
    flagged appropriately when the chip is registered.

Based on previous patches, and discussion both on and off LKML.

A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.

[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I noticed that there's a CONFIG_KPROBES check inside kernel/kprobes.c,
which is redundant.
Signed-off-by: NAbhishek Sagar <sagar.abhishek@gmail.com>
Acked-by: NMasami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently list of kretprobe instances are stored in kretprobe object (as
used_instances,free_instances) and in kretprobe hash table.  We have one
global kretprobe lock to serialise the access to these lists.  This causes
only one kretprobe handler to execute at a time.  Hence affects system
performance, particularly on SMP systems and when return probe is set on
lot of functions (like on all systemcalls).

Solution proposed here gives fine-grain locks that performs better on SMP
system compared to present kretprobe implementation.

Solution:

 1) Instead of having one global lock to protect kretprobe instances
    present in kretprobe object and kretprobe hash table.  We will have
    two locks, one lock for protecting kretprobe hash table and another
    lock for kretporbe object.

 2) We hold lock present in kretprobe object while we modify kretprobe
    instance in kretprobe object and we hold per-hash-list lock while
    modifying kretprobe instances present in that hash list.  To prevent
    deadlock, we never grab a per-hash-list lock while holding a kretprobe
    lock.

 3) We can remove used_instances from struct kretprobe, as we can
    track used instances of kretprobe instances using kretprobe hash
    table.

Time duration for kernel compilation ("make -j 8") on a 8-way ppc64 system
with return probes set on all systemcalls looks like this.

cacheline              non-cacheline             Un-patched kernel
aligned patch 	       aligned patch
===============================================================================
real    9m46.784s       9m54.412s                  10m2.450s
user    40m5.715s       40m7.142s                  40m4.273s
sys     2m57.754s       2m58.583s                  3m17.430s
===========================================================

Time duration for kernel compilation ("make -j 8) on the same system, when
kernel is not probed.
=========================
real    9m26.389s
user    40m8.775s
sys     2m7.283s
=========================
Signed-off-by: NSrinivasa DS <srinivasa@in.ibm.com>
Signed-off-by: NJim Keniston <jkenisto@us.ibm.com>
Acked-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The sm501_gpio_pin2nr() routine returns the wrong values for gpios in the
upper bank.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the build problems if CONFIG_MFD_SM501_GPIO is not set, which is
generally when there is no gpiolib support available as currently happens
on x86 when building PCI SM501.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Tested-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixup the comments from the patch that added the gpiolib support from
Andrew Morton.  These include spotting some missing frees on error or
release, and changing a memcpy for a type-safe assingment.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for adding the GPIO based I2C resources.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The SM501 PCI card requires a dyanmic gpio allocation as the number of
cards is not known at compile time.  Fixup the platform data and
registration to deal with this.
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NArnaud Patard <apatard@mandriva.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for exporting the GPIOs on the SM501 via gpiolib.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add callback to get or set the power control if the device has the sleep
connected to some form of GPIO.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All ratelimit user use same jiffies and burst params, so some messages
(callbacks) will be lost.

For example:
a call printk_ratelimit(5 * HZ, 1)
b call printk_ratelimit(5 * HZ, 1) before the 5*HZ timeout of a, then b will
will be supressed.

- rewrite __ratelimit, and use a ratelimit_state as parameter.  Thanks for
  hints from andrew.

- Add WARN_ON_RATELIMIT, update rcupreempt.h

- remove __printk_ratelimit

- use __ratelimit in net_ratelimit
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the %p format string which already accounts for the padding you need
with a pointer type on a particular architecture.

Also replace the macro with a static inline function to match the rest of
the file.

Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Arjan noted that the list_head debugging is BUG'ing when it detects
corruption.  By causing the box to panic immediately, we're possibly
losing some bug reports.  Changing this to a WARN() should mean we at the
least start seeing reports collected at kerneloops.org
Signed-off-by: NDave Jones <davej@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that WARN() exists, we can fold some of the printk's into it.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace a printk+WARN_ON() by a WARN(); this increases the chance of the
string making it into the bugreport (ie: it goes inside the
---[ cut here ]--- section)
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a WARN() macro that acts like WARN_ON(), with the added feature that it
takes a printk like argument that is printed as part of the warning message.

[akpm@linux-foundation.org: fix printk arguments]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We want to use WARN() as a variant of WARN_ON(), however a few drivers are
using WARN() internally.  This patch renames these to WARNING() to avoid the
namespace clash.  A few cases were defining but not using the thing, for those
cases I just deleted the definition.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Acked-by: NGreg KH <greg@kroah.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k allmodconfig:

drivers/misc/hpilo.c: In function 'ilo_ccb_close':
drivers/misc/hpilo.c:225: error: implicit declaration of function 'pci_free_consistent'
drivers/misc/hpilo.c: In function 'ilo_ccb_open':
drivers/misc/hpilo.c:244: error: implicit declaration of function 'pci_alloc_consistent'
drivers/misc/hpilo.c:245: warning: assignment makes pointer from integer without a cast

Cc: David Altobelli <david.altobelli@hp.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Describe a setup that integrates better with Emacs' cc-mode and also fixes
up the alignment of continuation lines to really only use tabs.
Signed-off-by: NJohannes Weiner <hannes@saeurebad.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

int Version_* is only used with ksymoops, which is only needed (according
to README and Documentation/Changes) if CONFIG_KALLSYMS is NOT defined.
Therefore this patch defines version_string only if CONFIG_KALLSYMS is not
defined.
Signed-off-by: NDaniel Guilak <daniel@danielguilak.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDaniel Guilak <daniel@danielguilak.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove apparently obsolete content from init.h referring to gcc 2.9x
and to "no_module_init".
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Add MODULE_ALIAS() to the hotpluggable parport platform drivers, to
re-enable auto loading.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Add MODULE_ALIAS() to the MFD platform drivers, to re-enable auto loading.

[dbrownell@users.sourceforge.net: one was missing]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee ("platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Add MODULE_ALIAS() to the hotpluggable "power" drivers drivers, to
re-enable auto loading.

[dbrownell@users.sourceforge.net: one was missing]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Inflate requires some dynamic memory allocation very early in the boot
process and this is provided with a set of four functions:
malloc/free/gzip_mark/gzip_release.

The old inflate code used a mark/release strategy rather than implement
free.  This new version instead keeps a count on the number of outstanding
allocations and when it hits zero, it resets the malloc arena.

This allows removing all the mark and release implementations and unifying
all the malloc/free implementations.

The architecture-dependent code must define two addresses:
 - free_mem_ptr, the address of the beginning of the area in which
   allocations should be made
 - free_mem_end_ptr, the address of the end of the area in which
   allocations should be made. If set to 0, then no check is made on
   the number of allocations, it just grows as much as needed

The architecture-dependent code can also provide an arch_decomp_wdog()
function call.  This function will be called several times during the
decompression process, and allow to notify the watchdog that the system is
still running.  If an architecture provides such a call, then it must
define ARCH_HAS_DECOMP_WDOG so that the generic inflate code calls
arch_decomp_wdog().

Work initially done by Matt Mackall, updated to a recent version of the
kernel and improved by me.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fs/exec.c used to need mman.h pagemap.h swap.h and rmap.h when it did
mm-ish stuff in install_arg_page(); but no need for them after 2.6.22.

[akpm@linux-foundation.org: unbreak arm]
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We duplicate alloc/free_thread_info defines on many platforms (the
majority uses __get_free_pages/free_pages).  This patch defines common
defines and removes these duplicated defines.
__HAVE_ARCH_THREAD_INFO_ALLOCATOR is introduced for platforms that do
something different.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver adds support for reading and configuring certain information
on modern HP laptops with WMI BIOS interfaces.  It supports enabling and
disabling the ambient light sensor, querying attached displays and hard
drive temperature, sending events on docking and querying the state of the
dock and toggling the state of the wifi, bluetooth and wwan hardware via
rfkill.  It also makes the little "(i)" button work on machines that send
that via WMI rather than via the keyboard controller.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Presently call_usermodehelper_setup() uses GFP_ATOMIC.  but it can return
NULL _very_ easily.

GFP_ATOMIC is needed only when we can't sleep.  and, GFP_KERNEL is robust
and better.

thus, I add gfp_mask argument to call_usermodehelper_setup().

So, its callers pass the gfp_t as below:

call_usermodehelper() and call_usermodehelper_keys():
	depend on 'wait' argument.
call_usermodehelper_pipe():
	always GFP_KERNEL because always run under process context.
orderly_poweroff():
	pass to GFP_ATOMIC because may run under interrupt context.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Paul Menage" <menage@google.com>
Reviewed-by: NLi Zefan <lizf@cn.fujitsu.com>
Acked-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some bits were missed when the tipar driver was removed.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Several compilers offer "long long" without claiming to support C99.

Considering how frequent __s64/__u64 are used our userspace headers are
anyway unusable without __s64/__u64 available.

Always offer __s64/__u64 to non-gcc non-C99 compilers - if they provide
"long long" that makes the headers compiling and if they don't they are
anyway screwed.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cc: Adrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Build kernel/profile.o only if CONFIG_PROFILING is enabled.

This makes CONFIG_PROFILING=n kernels smaller.

As a bonus, some profile_tick() calls and one branch from schedule() are
now eliminated with CONFIG_PROFILING=n (but I doubt these are
measurable effects).

This patch changes the effects of CONFIG_PROFILING=n, but I don't think
having more than two choices would be the better choice.

This patch also adds the name of the first parameter to the prototypes
of profile_{hits,tick}() since I anyway had to add them for the dummy
functions.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All uses of list_for_each_rcu() can be profitably replaced by the
easier-to-use list_for_each_entry_rcu().  This patch makes this change for
networking, in preparation for removing the list_for_each_rcu() API
entirely.
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This will probably never trigger... but it won't hurt to be careful.

http://googleresearch.blogspot.com/2006/06/extra-extra-read-all-about-it-nearly.htmlSigned-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Cc: Joshua Bloch <jjb@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In many cases, especially in networking, it can be beneficial to know at
compile time whether the architecture can do unaligned accesses efficiently.
This patch introduces a new Kconfig symbol

	HAVE_EFFICIENT_UNALIGNED_ACCESS

for that purpose and adds it to the powerpc and x86 architectures.  Also add
some documentation about alignment and networking, and especially one intended
use of this symbol.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: Ingo Molnar <mingo@elte.hu> [x86 architecture part]
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the conditional surrounding the definition of list_add() from list.h
since, if you define CONFIG_DEBUG_LIST, the definition you will subsequently
pick up from lib/list_debug.c will be absolutely identical, at which point you
can remove that redundant definition from list_debug.c as well.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>