Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.

In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'weight' field is only used to pass the weigth to napi initialization
function. This commit removes the field, and instead uses a fixed value to
initialize the napi context.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver does not support multiple rx queues, and so it's a waste
of resources to have a default number larger than one (1).
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_prepare_mac_addr_change and eth_commit_mac_addr_change, instead
of manually checking and storing the MAC address, which makes the
code slightly more robust. This fixes the lack of valid MAC address check
in the driver's .ndo_set_mac_address hook.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit cleans-up mvneta_init(), which initializes the hardware
and allocates the rx/qx queues. The queue allocation is simplified
by using devm_kcalloc instead of kzalloc. The unused phy_addr parameter
is removed. While here, the 'hal' references in the comments are removed.
This commit makes no functionality change.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit checks the return code of mvneta_setup_txq() call
in mvneta_change_mtu(). Also, use the netdevice pointer directly
instead of dereferencing the port structure. While here, let's
fix a tiny comment typo.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A tiny clean-up to improve readability. This commit makes no functionality
change.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the TSO helper API has been introduced, this commit makes use
of it to implement the TSO in this driver.

Using iperf to test and vmstat to check the CPU usage, shows a substantial
CPU usage drop when TSO is on (~15% vs. ~25%). HTTP-based tests performed
by Willy Tarreau have shown performance improvements.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rework mvneta_tx() so that the code that performs the final handling
before a sk_buff is transmitted is done only if the numbers of fragments
processed if positive.

This is preparation work to add the support for software TSO.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to ease the addition of new features, let's factorize the
feature list.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following the introduction of of_phy_register_fixed_link(), this patch
introduces fixed link support in the mvneta driver, for Marvell Armada
370/XP SOCs.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5445eaf3 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.

However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.

In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.

Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:

 - QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
   the SERDES is configured in QSGMII. Technically speaking,
   configuring the SERDES of the first port would be sufficient, but
   it is simpler to do it on all ports.

 - SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
   the SERDES is configured as SGMII.

 - RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
   cleared, and no SERDES configuration is done, because RGMII is not
   using SERDES lanes.

 - other: an error is returned. For this reason, the
   mvneta_port_power_up() now returns an int instead of nothing, and
   the return value is checked by mvneta_probe().

This has been successfully tested on:

 * Armada XP DB, which has two RGMII and two SGMII connections
 * Armada XP GP, which uses QSGMII for its four interfaces
 * Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit e3a8786c. While
this commit allows to use the mvneta driver as a module on some
configurations, it breaks other configurations even if mvneta is used
built-in.

This breakage is due to the fact that on some RGMII platforms, the PCS
bit has to be set, and on some other platforms, it has to be
cleared. At the moment, we lack informations to know exactly the
significance of this bit (the datasheet only says "enables PCS"), and
so we can't produce a patch that will work on all platforms at this
point. And since this change is breaking the network completely for
many users, it's much better to revert it for now. We'll come back
later with a proper fix that takes into account all platforms.

Basically:

 * Armada XP GP is configured as RGMII-ID, and needs the PCS bit to be
   set.
 * Armada 370 Mirabox is configured as RGMII-ID, and needs the PCS bit
   to be cleared.

And at the moment, we don't know how to make the distinction between
those two cases. One hint is that the Armada XP GP appears in fact to
be using a QSGMII connection with the PHY (Quad-SGMII), but
configuring it as SGMII doesn't work, while RGMII-ID works. This needs
more investigation, but in the mean time, let's unbreak the network
for all those users.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: NArnaud Ebalard <arno@natisbad.org>
Reported-by: NAlexander Reuter <Alexander.Reuter@gmx.net>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=73401
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.

This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.

This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5445eaf3 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.

However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.

However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.

Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.

In detail, to achieve this, the commit:

 * Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
   not specific to SGMII, but also used on RGMII configurations.

 * Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
   the MVNETA_SERDES_CFG value in RGMII configurations.

 * Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
   functions, and instead directly do the SGMII/RGMII configuration in
   mvneta_port_up(), from where those functions where called. It is
   worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
   parameter that was always passed as '1', so it was pretty useless.

 * Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
   register to the appropriate value depending on the RGMII vs. SGMII
   configuration. It also unconditionally set the PCS_ENABLE bit (was
   already done for SGMII, but is now also needed for RGMII), and sets
   the PORT_RGMII bit (which was already done for both SGMII and
   RGMII).

This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: NSteve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf3 mvneta: Try to fix mvneta when compiled as module
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.

Cc: stable@vger.kernel.org
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the bh safe variant with the hard irq safe variant.

We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.

Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function return parameter is not used in mvneta_tx_done_gbe(),
where the function is called. This patch makes the function return
void.
Reviewed-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mvneta_tx_done_gbe() return value and third parameter are no more
used. This patch changes the function prototype and removes a useless
variable where the function is called.
Reviewed-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped. We set the limit to 256 bytes which seems to give good results both
on the XP-GP board and on the AX3/4.

The Rx small packet rate increased by 16.4% doing this, from 486kpps to
573kpps. It is worth noting that even the call to the function
dma_sync_single_range_for_cpu() is expensive (300 ns) although less
than dma_unmap_single(). Without it, the packet rate raises to 711kpps
(+24% more). Thus on systems where coherency from device to CPU is
guaranteed by a snoop control unit, this patch should provide even more
gains, and probably rx_copybreak could be increased.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of build_skb() to allocate frags on the RX path. When frag size
is lower than a page size, we can use netdev_alloc_frag(), and we fall back
to kmalloc() for larger sizes. The frag size is stored into the mvneta_port
struct. The alloc/free functions check the frag size to decide what alloc/
free method to use. MTU changes are safe because the MTU change function
stops the device and clears the queues before applying the change.

With this patch, I observed a reproducible 2% performance improvement on
HTTP-based benchmarks, and 5% on small packet RX rate.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the mvneta driver tries to prefetch the current Rx
descriptor during read. Tests have shown that prefetching the
next one instead increases general performance by about 1% on
HTTP traffic.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At several places, we already know the value of the rx status but
we call functions which dereference the pointer again to get it
and don't need the descriptor for anything else. Simplify this
task by replacing the rx desc pointer by the status word itself.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make mvneta_rxq_fill() use mvneta_rx_refill() instead of using
duplicate code.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, mvneta_txq_bufs_free() calls mvneta_tx_done_policy() with
a non-null cause to retrieve the pointer to the next queue to process.
There are useless tests on the return queue number and on the pointer,
all of which are well defined within a known limited set. This code
path is fast, although not critical. Removing 3 tests here that the
compiler could not optimize (verified) is always desirable.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now the mvneta driver doesn't handle Tx IRQ, and relies on two
mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx()
and a timer. If a burst of packets is emitted faster than the device
can send them, then the queue is stopped until next wake-up of the
timer 10ms later. This causes jerky output traffic with bursts and
pauses, making it difficult to reach line rate with very few streams.

A test on UDP traffic shows that it's not possible to go beyond 134
Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed
traffic tends to observe pauses as well if the traffic is bursty,
making it even burstier after the wake-up.

It seems that this feature was inherited from the original driver but
nothing there mentions any reason for not using the interrupt instead,
which the chip supports.

Thus, this patch enables Tx interrupts and removes the timer. It does
the two at once because it's not really possible to make the two
mechanisms coexist, so a split patch doesn't make sense.

First tests performed on a Mirabox (Armada 370) show that less CPU
seems to be used when sending traffic. One reason might be that we now
call the mvneta_tx_done_gbe() with a mask indicating which queues have
been done instead of looping over all of them.

The same UDP test above now happily reaches 987 Mbps / 87.7 kpps.
Single-stream TCP traffic can now more easily reach line rate. HTTP
transfers of 1 MB objects over a single connection went from 730 to
840 Mbps. It is even possible to go significantly higher (>900 Mbps)
by tweaking tcp_tso_win_divisor.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell has not published the chip's datasheet yet, so it's very hard
to find the relevant bits to manipulate to change the IRQ behaviour.
Fortunately, these bits are described in the proprietary LSP patch set
which is publicly available here :

    http://www.plugcomputer.org/downloads/mirabox/

So let's put them back in the driver in order to reduce the burden of
current and future maintenance.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a queue timeout is reported, we can oops because of some
schedules while the caller is atomic, as shown below :

  mvneta d0070000.ethernet eth0: tx timeout
  BUG: scheduling while atomic: bash/1528/0x00000100
  Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv]
  CPU: 2 PID: 1528 Comm: bash Tainted: G        WC   3.13.0-rc4-mvebu-nf #180
  [<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc)
  [<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64)
  [<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c)
  [<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec)
  [<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118)
  [<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14)
  [<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194)
  [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24)
  [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4)
  [<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c)
  [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170)
  [<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8)
  [<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98)
  [<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60)
  [<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8)
  [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60)

Ben Hutchings attempted to propose a better fix consisting in using a
scheduled work for this, but while it fixed this panic, it caused other
random freezes and panics proving that the reset sequence in the driver
is unreliable and that additional fixes should be investigated.

When sending multiple streams over a link limited to 100 Mbps, Tx timeouts
happen from time to time, and the driver correctly recovers only when the
function is disabled.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything
when they update the stats, and as a result, it randomly happens that
the stats freeze on SMP if two updates happen during stats retrieval.
This is very easily reproducible by starting two HTTP servers and binding
each of them to a different CPU, then consulting /proc/net/dev in loops
during transfers, the interface should immediately lock up. This issue
also randomly happens upon link state changes during transfers, because
the stats are collected in this situation, but it takes more attempts to
reproduce it.

The comments in netdevice.h suggest using per_cpu stats instead to get
rid of this issue.

This patch implements this. It merges both rx_stats and tx_stats into
a single "stats" member with a single syncp. Both mvneta_rx() and
mvneta_rx() now only update the a single CPU's counters.

In turn, mvneta_get_stats64() does the summing by iterating over all CPUs
to get their respective stats.

With this change, stats are still correct and no more lockup is encountered.

Note that this bug was present since the first import of the mvneta
driver.  It might make sense to backport it to some stable trees. If
so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats
out of the hot path".

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Better count packets and bytes in the stack and on 32 bit then
accumulate them at the end for once. This saves two memory writes
and two memory barriers per packet. The incoming packet rate was
increased by 4.7% on the Openblocks AX3 thanks to this.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code unmaps the DMA mapping created for rx skb_buff's by
using the data_size as the the mapping size. This is wrong since the
correct size to specify should match the size used to create the mapping.

This commit removes the following DMA_API_DEBUG warning:

------------[ cut here ]------------
WARNING: at lib/dma-debug.c:887 check_unmap+0x3a8/0x860()
mvneta d0070000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002eb80000] [map size=1600 bytes] [unmap size=66 bytes]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.21-01444-ga88ae13-dirty #92
[<c0013600>] (unwind_backtrace+0x0/0xf8) from [<c0010fb8>] (show_stack+0x10/0x14)
[<c0010fb8>] (show_stack+0x10/0x14) from [<c001afa0>] (warn_slowpath_common+0x48/0x68)
[<c001afa0>] (warn_slowpath_common+0x48/0x68) from [<c001b01c>] (warn_slowpath_fmt+0x30/0x40)
[<c001b01c>] (warn_slowpath_fmt+0x30/0x40) from [<c018d0fc>] (check_unmap+0x3a8/0x860)
[<c018d0fc>] (check_unmap+0x3a8/0x860) from [<c018d734>] (debug_dma_unmap_page+0x64/0x70)
[<c018d734>] (debug_dma_unmap_page+0x64/0x70) from [<c0233f78>] (mvneta_rx+0xec/0x468)
[<c0233f78>] (mvneta_rx+0xec/0x468) from [<c023436c>] (mvneta_poll+0x78/0x16c)
[<c023436c>] (mvneta_poll+0x78/0x16c) from [<c02db468>] (net_rx_action+0x94/0x160)
[<c02db468>] (net_rx_action+0x94/0x160) from [<c0021e68>] (__do_softirq+0xe8/0x1d0)
[<c0021e68>] (__do_softirq+0xe8/0x1d0) from [<c0021ff8>] (do_softirq+0x4c/0x58)
[<c0021ff8>] (do_softirq+0x4c/0x58) from [<c0022228>] (irq_exit+0x58/0x90)
[<c0022228>] (irq_exit+0x58/0x90) from [<c000e7c8>] (handle_IRQ+0x3c/0x94)
[<c000e7c8>] (handle_IRQ+0x3c/0x94) from [<c0008548>] (armada_370_xp_handle_irq+0x4c/0xb4)
[<c0008548>] (armada_370_xp_handle_irq+0x4c/0xb4) from [<c000dc20>] (__irq_svc+0x40/0x50)
Exception stack(0xc04f1f70 to 0xc04f1fb8)
1f60:                                     c1fe46f8 00000000 00001d92 00001d92
1f80: c04f0000 c04f0000 c04f84a4 c03e081c c05220e7 00000001 c05220e7 c04f0000
1fa0: 00000000 c04f1fb8 c000eaf8 c004c048 60000113 ffffffff
[<c000dc20>] (__irq_svc+0x40/0x50) from [<c004c048>] (cpu_startup_entry+0x54/0x128)
[<c004c048>] (cpu_startup_entry+0x54/0x128) from [<c04c1a14>] (start_kernel+0x29c/0x2f0)
[<c04c1a14>] (start_kernel+0x29c/0x2f0) from [<00008074>] (0x8074)
---[ end trace d4955f6acd178110 ]---
Mapped at:
 [<c018d600>] debug_dma_map_page+0x4c/0x11c
 [<c0235d6c>] mvneta_setup_rxqs+0x398/0x598
 [<c0236084>] mvneta_open+0x40/0x17c
 [<c02dbbd4>] __dev_open+0x9c/0x100
 [<c02dbe58>] __dev_change_flags+0x7c/0x134
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.

The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.

This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.

Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.

Feedback would be appreciated!
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Acked-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address().
Signed-off-by: NLuka Perkov <luka@openwrt.org>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes a long-standing bug that has been reported by many
users: on some Armada 370 platforms, only the network interface that
has been used in U-Boot to tftp the kernel works properly in
Linux. The other network interfaces can see a 'link up', but are
unable to transmit data. The reports were generally made on the Armada
370-based Mirabox, but have also been given on the Armada 370-RD
board.

The network MAC in the Armada 370/XP (supported by the mvneta driver
in Linux) has a functionality that allows it to continuously poll the
PHY and directly update the MAC configuration accordingly (speed,
duplex, etc.). The very first versions of the driver submitted for
review were using this hardware mechanism, but due to this, the driver
was not integrated with the kernel phylib. Following reviews, the
driver was changed to use the phylib, and therefore a software based
polling. In software based polling, Linux regularly talks to the PHY
over the MDIO bus, and sees if the link status has changed. If it's
the case then the adjust_link() callback of the driver is called to
update the MAC configuration accordingly.

However, it turns out that the adjust_link() callback was not
configuring the hardware in a completely correct way: while it was
setting the speed and duplex bits correctly, it wasn't telling the
hardware to actually take into account those bits rather than what the
hardware-based PHY polling mechanism has concluded. So, in fact the
adjust_link() callback was basically a no-op.

However, the network happened to be working because on the network
interfaces used by U-Boot for tftp on Armada 370 platforms because the
hardware PHY polling was enabled by the bootloader, and left enabled
by Linux. However, the second network interface not used for tftp (or
both network interfaces if the kernel is loaded from USB, NAND or SD
card) didn't had the hardware PHY polling enabled.

This patch fixes this situation by:

 (1) Making sure that the hardware PHY polling is disabled by clearing
     the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL
     register in the driver ->probe() function.

 (2) Making sure that the duplex and speed selections made by the
     adjust_link() callback are taken into account by clearing the
     MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the
     MVNETA_GMAC_AUTONEG_CONFIG register.

This patch has been tested on Armada 370 Mirabox, and now both network
interfaces are usable after boot.

[ Problem introduced by commit c5aff182 ("net: mvneta: driver for
  Marvell Armada 370/XP network unit") ]
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Jochen De Smet <jochen.armkernel@leahnim.org>
Cc: Peter Sanford <psanford@nearbuy.io>
Cc: Ethan Tuttle <ethan@ethantuttle.com>
Cc: Chény Yves-Gael <yves@cheny.fr>
Cc: Ryan Press <ryan@presslab.us>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: vdonnefort@lacie.com
Cc: stable@vger.kernel.org
Acked-by: NJason Cooper <jason@lakedaemon.net>
Tested-by: NVincent Donnefort <vdonnefort@gmail.com>
Tested-by: NYves-Gael Cheny <yves@cheny.fr>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the mvneta driver is compiled as module, the clock is disabled before
it's loading. This will reset the registers values and all configuration
made by the bootloader.

This patch sets the "sgmii serdes configuration" register to a magical value
found in:
https://github.com/yellowback/ubuntu-precise-armadaxp/blob/master/arch/arm/mach-armadaxp/armada_xp_family/ctrlEnv/mvCtrlEnvLib.c

With this change, the interrupts are working/generated and ethernet is
working.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>