When KVM emulates an exit from L2 to L1, it loads L1 CR4 into the
guest CR4. Before this CR4 loading, the guest CR4 refers to L2
CR4. Because these two CR4's are in different levels of guest, we
should vmx_set_cr4() rather than kvm_set_cr4() here. The latter, which
is used to handle guest writes to its CR4, checks the guest change to
CR4 and may fail if the change is invalid.

The failure may cause trouble. Consider we start
  a L1 guest with non-zero L1 PCID in use,
     (i.e. L1 CR4.PCIDE == 1 && L1 CR3.PCID != 0)
and
  a L2 guest with L2 PCID disabled,
     (i.e. L2 CR4.PCIDE == 0)
and following events may happen:

1. If kvm_set_cr4() is used in load_vmcs12_host_state() to load L1 CR4
   into guest CR4 (in VMCS01) for L2 to L1 exit, it will fail because
   of PCID check. As a result, the guest CR4 recorded in L0 KVM (i.e.
   vcpu->arch.cr4) is left to the value of L2 CR4.

2. Later, if L1 attempts to change its CR4, e.g., clearing VMXE bit,
   kvm_set_cr4() in L0 KVM will think L1 also wants to enable PCID,
   because the wrong L2 CR4 is used by L0 KVM as L1 CR4. As L1
   CR3.PCID != 0, L0 KVM will inject GP to L1 guest.

Fixes: 4704d0be ("KVM: nVMX: Exiting from L2 to L1")
Cc: qemu-stable@nongnu.org
Signed-off-by: NHaozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

------------[ cut here ]------------
 WARNING: CPU: 4 PID: 5280 at /home/kernel/linux/arch/x86/kvm//vmx.c:11394 nested_vmx_vmexit+0xc2b/0xd70 [kvm_intel]
 CPU: 4 PID: 5280 Comm: qemu-system-x86 Tainted: G        W  OE   4.13.0+ #17
 RIP: 0010:nested_vmx_vmexit+0xc2b/0xd70 [kvm_intel]
 Call Trace:
  ? emulator_read_emulated+0x15/0x20 [kvm]
  ? segmented_read+0xae/0xf0 [kvm]
  vmx_inject_page_fault_nested+0x60/0x70 [kvm_intel]
  ? vmx_inject_page_fault_nested+0x60/0x70 [kvm_intel]
  x86_emulate_instruction+0x733/0x810 [kvm]
  vmx_handle_exit+0x2f4/0xda0 [kvm_intel]
  ? kvm_arch_vcpu_ioctl_run+0xd2f/0x1c60 [kvm]
  kvm_arch_vcpu_ioctl_run+0xdab/0x1c60 [kvm]
  ? kvm_arch_vcpu_load+0x62/0x230 [kvm]
  kvm_vcpu_ioctl+0x340/0x700 [kvm]
  ? kvm_vcpu_ioctl+0x340/0x700 [kvm]
  ? __fget+0xfc/0x210
  do_vfs_ioctl+0xa4/0x6a0
  ? __fget+0x11d/0x210
  SyS_ioctl+0x79/0x90
  entry_SYSCALL_64_fastpath+0x23/0xc2

A nested #PF is triggered during L0 emulating instruction for L2. However, it
doesn't consider we should not break L1's vmlauch/vmresme. This patch fixes
it by queuing the #PF exception instead ,requesting an immediate VM exit from
L2 and keeping the exception for L1 pending for a subsequent nested VM exit.

This should actually work all the time, making vmx_inject_page_fault_nested
totally unnecessary.  However, that's not working yet, so this patch can work
around the issue in the meanwhile.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

This fixes a compilation failure on 32-bit systems.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The simplify part: do not touch pi_desc.nv, we can set it when the
VCPU is first created.  Likewise, pi_desc.sn is only handled by
vmx_vcpu_pi_load, do not touch it in __pi_post_block.

The fix part: do not check kvm_arch_has_assigned_device, instead
check the SN bit to figure out whether vmx_vcpu_pi_put ran before.
This matches what the previous patch did in pi_post_block.

Cc: Huangweidong <weidong.huang@huawei.com>
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: wangxin <wangxinxin.wang@huawei.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: NLongpeng (Mike) <longpeng2@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

In some cases, for example involving hot-unplug of assigned
devices, pi_post_block can forget to remove the vCPU from the
blocked_vcpu_list.  When this happens, the next call to
pi_pre_block corrupts the list.

Fix this in two ways.  First, check vcpu->pre_pcpu in pi_pre_block
and WARN instead of adding the element twice in the list.  Second,
always do the list removal in pi_post_block if vcpu->pre_pcpu is
set (not -1).

The new code keeps interrupts disabled for the whole duration of
pi_pre_block/pi_post_block.  This is not strictly necessary, but
easier to follow.  For the same reason, PI.ON is checked only
after the cmpxchg, and to handle it we just call the post-block
code.  This removes duplication of the list removal code.

Cc: Huangweidong <weidong.huang@huawei.com>
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: wangxin <wangxinxin.wang@huawei.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: NLongpeng (Mike) <longpeng2@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Simple code movement patch, preparing for the next one.

Cc: Huangweidong <weidong.huang@huawei.com>
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: wangxin <wangxinxin.wang@huawei.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: NLongpeng (Mike) <longpeng2@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

For inline asm statements which have a CALL instruction, we list the
stack pointer as a constraint to convince GCC to ensure the frame
pointer is set up first:

  static inline void foo()
  {
	register void *__sp asm(_ASM_SP);
	asm("call bar" : "+r" (__sp))
  }

Unfortunately, that pattern causes Clang to corrupt the stack pointer.

The fix is easy: convert the stack pointer register variable to a global
variable.

It should be noted that the end result is different based on the GCC
version.  With GCC 6.4, this patch has exactly the same result as
before:

	defconfig	defconfig-nofp	distro		distro-nofp
 before	9820389		9491555		8816046		8516940
 after	9820389		9491555		8816046		8516940

With GCC 7.2, however, GCC's behavior has changed.  It now changes its
behavior based on the conversion of the register variable to a global.
That somehow convinces it to *always* set up the frame pointer before
inserting *any* inline asm.  (Therefore, listing the variable as an
output constraint is a no-op and is no longer necessary.)  It's a bit
overkill, but the performance impact should be negligible.  And in fact,
there's a nice improvement with frame pointers disabled:

	defconfig	defconfig-nofp	distro		distro-nofp
 before	9796316		9468236		9076191		8790305
 after	9796957		9464267		9076381		8785949

So in summary, while listing the stack pointer as an output constraint
is no longer necessary for newer versions of GCC, it's still needed for
older versions.
Suggested-by: NAndrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/3db862e970c432ae823cf515c52b54fec8270e0e.1505942196.git.jpoimboe@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

For nested virt we maintain multiple VMCS that can run on a vCPU. So it is
incorrect to keep vmcs_host_cr3 and vmcs_host_cr4, whose purpose is caching
the value of the rarely changing HOST_CR3 and HOST_CR4 VMCS fields, in
vCPU-wide data structures.

Hyper-V nested on KVM runs into this consistently for me with PCID enabled.
CR3 is updated with a new value, unlikely(cr3 != vmx->host_state.vmcs_host_cr3)
fires, and the currently loaded VMCS is updated. Then we switch from L2 to
L1 and the next exit reverts CR3 to its old value.

Fixes: d6e41f11 ("x86/mm, KVM: Teach KVM's VMX code that CR3 isn't a constant")
Signed-off-by: NLadi Prosek <lprosek@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

WARN_ON_ONCE(pi_test_sn(&vmx->pi_desc)) in kvm_vcpu_trigger_posted_interrupt()
intends to detect the violation of invariant that VT-d PI notification
event is not suppressed when vcpu is in the guest mode. Because the
two checks for the target vcpu mode and the target suppress field
cannot be performed atomically, the target vcpu mode may change in
between. If that does happen, WARN_ON_ONCE() here may raise false
alarms.

As the previous patch fixed the real invariant breaker, remove this
WARN_ON_ONCE() to avoid false alarms, and document the allowed cases
instead.
Signed-off-by: NHaozhong Zhang <haozhong.zhang@intel.com>
Reported-by: N"Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com>
Reported-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Fixes: 28b835d6 ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted")
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

In kvm_vcpu_trigger_posted_interrupt() and pi_pre_block(), KVM
assumes that PI notification events should not be suppressed when the
target vCPU is not blocked.

vmx_update_pi_irte() sets the SN field before changing an interrupt
from posting to remapping, but it does not check the vCPU mode.
Therefore, the change of SN field may break above the assumption.
Besides, I don't see reasons to suppress notification events here, so
remove the changes of SN field to avoid race condition.
Signed-off-by: NHaozhong Zhang <haozhong.zhang@intel.com>
Reported-by: N"Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com>
Reported-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Fixes: 28b835d6 ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted")
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

When emulating a nested VM-entry from L1 to L2, several control field
validation checks are deferred to the hardware. Should one of these
validation checks fail, vcpu_vmx_run will set the vmx->fail flag. When
this happens, the L2 guest state is not loaded (even in part), and
execution should continue in L1 with the next instruction after the
VMLAUNCH/VMRESUME.

The VMCS12 is not modified (except for the VM-instruction error
field), the VMCS12 MSR save/load lists are not processed, and the CPU
state is not loaded from the VMCS12 host area. Moreover, the vmcs02
exit reason is stale, so it should not be consulted for any reason.
Signed-off-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

On an early VMLAUNCH/VMRESUME failure (i.e. one which sets the
VM-instruction error field of the current VMCS), the launch state of
the current VMCS is not set to "launched," and the VM-exit information
fields of the current VMCS (including IDT-vectoring information and
exit reason) are stale.

On a late VMLAUNCH/VMRESUME failure (i.e. one which sets the high bit
of the exit reason field), the launch state of the current VMCS is not
set to "launched," and only two of the VM-exit information fields of
the current VMCS are modified (exit reason and exit
qualification). The remaining VM-exit information fields of the
current VMCS (including IDT-vectoring information, in particular) are
stale.
Signed-off-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

After a successful VM-entry, RFLAGS is cleared, with the exception of
bit 1, which is always set. This is handled by load_vmcs12_host_state.
Signed-off-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The value of the guest_irq argument to vmx_update_pi_irte() is
ultimately coming from a KVM_IRQFD API call. Do not BUG() in
vmx_update_pi_irte() if the value is out-of bounds. (Especially,
since KVM as a whole seems to hang after that.)

Instead, print a message only once if we find that we don't have a
route for a certain IRQ (which can be out-of-bounds or within the
array).

This fixes CVE-2017-1000252.

Fixes: efc64404 ("KVM: x86: Update IRTE for posted-interrupts")
Signed-off-by: NJan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If L1 does not specify the "use TPR shadow" VM-execution control in
vmcs12, then L0 must specify the "CR8-load exiting" and "CR8-store
exiting" VM-execution controls in vmcs02. Failure to do so will give
the L2 VM unrestricted read/write access to the hardware CR8.

This fixes CVE-2017-12154.
Signed-off-by: NJim Mattson <jmattson@google.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Modify struct kvm_x86_ops.arch.apicv_active() to take struct kvm_vcpu
pointer as parameter in preparation to subsequent changes.
Signed-off-by: NSuravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

With removal of lguest some of the paravirt functions are no longer
needed:

	->read_cr4()
	->store_idt()
	->set_pmd_at()
	->set_pud_at()
	->pte_update()

Remove them.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akataria@vmware.com
Cc: boris.ostrovsky@oracle.com
Cc: chrisw@sous-sol.org
Cc: jeremy@goop.org
Cc: rusty@rustcorp.com.au
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20170904102527.25409-1-jgross@suse.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The first 32 bits of gate struct are the same for 32 and 64 bit kernels.

The 32-bit version uses desc_struct and no designated data structure,
so we need different accessors for 32 and 64 bit kernels.

Aside of that the macros which are necessary to build the 32-bit
gate descriptor are horrible to read.

Unify the gate structs and switch all code fiddling with it over.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170828064957.861974317@linutronix.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

According to the SDM, if the "use TPR shadow" VM-execution control is
1, bits 11:0 of the virtual-APIC address must be 0 and the address
should set any bits beyond the processor's physical-address width.
Signed-off-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Move it to struct kvm_arch_vcpu, replacing guest_pkru_valid with a
simple comparison against the host value of the register.  The write of
PKRU in addition can be skipped if the guest has not enabled the feature.
Once we do this, we need not test OSPKE in the host anymore, because
guest_CR4.PKE=1 implies host_CR4.PKE=1.

The static PKU test is kept to elide the code on older CPUs.
Suggested-by: NYang Zhang <zy107165@alibaba-inc.com>
Fixes: 1be0e61c
Cc: stable@vger.kernel.org
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

------------[ cut here ]------------
WARNING: CPU: 7 PID: 3861 at /home/kernel/ssd/kvm/arch/x86/kvm//vmx.c:11299 nested_vmx_vmexit+0x176e/0x1980 [kvm_intel]
CPU: 7 PID: 3861 Comm: qemu-system-x86 Tainted: G        W  OE   4.13.0-rc4+ #11
RIP: 0010:nested_vmx_vmexit+0x176e/0x1980 [kvm_intel]
Call Trace:
 ? kvm_multiple_exception+0x149/0x170 [kvm]
 ? handle_emulation_failure+0x79/0x230 [kvm]
 ? load_vmcs12_host_state+0xa80/0xa80 [kvm_intel]
 ? check_chain_key+0x137/0x1e0
 ? reexecute_instruction.part.168+0x130/0x130 [kvm]
 nested_vmx_inject_exception_vmexit+0xb7/0x100 [kvm_intel]
 ? nested_vmx_inject_exception_vmexit+0xb7/0x100 [kvm_intel]
 vmx_queue_exception+0x197/0x300 [kvm_intel]
 kvm_arch_vcpu_ioctl_run+0x1b0c/0x2c90 [kvm]
 ? kvm_arch_vcpu_runnable+0x220/0x220 [kvm]
 ? preempt_count_sub+0x18/0xc0
 ? restart_apic_timer+0x17d/0x300 [kvm]
 ? kvm_lapic_restart_hv_timer+0x37/0x50 [kvm]
 ? kvm_arch_vcpu_load+0x1d8/0x350 [kvm]
 kvm_vcpu_ioctl+0x4e4/0x910 [kvm]
 ? kvm_vcpu_ioctl+0x4e4/0x910 [kvm]
 ? kvm_dev_ioctl+0xbe0/0xbe0 [kvm]

The flag "nested_run_pending", which can override the decision of which should run
next, L1 or L2. nested_run_pending=1 means that we *must* run L2 next, not L1. This
is necessary in particular when L1 did a VMLAUNCH of L2 and therefore expects L2 to
be run (and perhaps be injected with an event it specified, etc.). Nested_run_pending
is especially intended to avoid switching  to L1 in the injection decision-point.

This can be handled just like the other cases in vmx_check_nested_events, instead of
having a special case in vmx_queue_exception.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

vmx_complete_interrupts() assumes that the exception is always injected,
so it can be dropped by kvm_clear_exception_queue().  However,
an exception cannot be injected immediately if it is: 1) originally
destined to a nested guest; 2) trapped to cause a vmexit; 3) happening
right after VMLAUNCH/VMRESUME, i.e. when nested_run_pending is true.

This patch applies to exceptions the same algorithm that is used for
NMIs, replacing exception.reinject with "exception.injected" (equivalent
to nmi_injected).

exception.pending now represents an exception that is queued and whose
side effects (e.g., update RFLAGS.RF or DR7) have not been applied yet.
If exception.pending is true, the exception might result in a nested
vmexit instead, too (in which case the side effects must not be applied).

exception.injected instead represents an exception that is going to be
injected into the guest at the next vmentry.
Reported-by: NRadim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Use kvm_event_needs_reinjection() encapsulation.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

This patch exposes 5 level page table feature to the VM.
At the same time, the canonical virtual address checking is
extended to support both 48-bits and 57-bits address width.
Signed-off-by: NYu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Extends the shadow paging code, so that 5 level shadow page
table can be constructed if VM is running in 5 level paging
mode.

Also extends the ept code, so that 5 level ept table can be
constructed if maxphysaddr of VM exceeds 48 bits. Unlike the
shadow logic, KVM should still use 4 level ept table for a VM
whose physical address width is less than 48 bits, even when
the VM is running in 5 level paging mode.
Signed-off-by: NYu Zhang <yu.c.zhang@linux.intel.com>
[Unconditionally reset the MMU context in kvm_cpuid_update.
 Changing MAXPHYADDR invalidates the reserved bit bitmasks.
 - Paolo]
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

A guest may not be configured to support XSAVES/XRSTORS, even when the host
does. If the guest does not support XSAVES/XRSTORS, clear the secondary
execution control so that the processor will raise #UD.

Also clear the "allowed-1" bit for XSAVES/XRSTORS exiting in the
IA32_VMX_PROCBASED_CTLS2 MSR, and pass through VMCS12's control in
the VMCS02.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

A guest may not be configured to support RDSEED, even when the host
does. If the guest does not support RDSEED, intercept the instruction
and synthesize #UD. Also clear the "allowed-1" bit for RDSEED exiting
in the IA32_VMX_PROCBASED_CTLS2 MSR.
Signed-off-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

A guest may not be configured to support RDRAND, even when the host
does. If the guest does not support RDRAND, intercept the instruction
and synthesize #UD. Also clear the "allowed-1" bit for RDRAND exiting
in the IA32_VMX_PROCBASED_CTLS2 MSR.
Signed-off-by: NJim Mattson <jmattson@google.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Currently, secondary execution controls are divided in three groups:

- static, depending mostly on the module arguments or the processor
  (vmx_secondary_exec_control)

- static, depending on CPUID (vmx_cpuid_update)

- dynamic, depending on nested VMX or local APIC state

Because walking CPUID is expensive, prepare_vmcs02 is using only
the first group.  This however is unnecessarily complicated.  Just
cache the static secondary execution controls, and then prepare_vmcs02
does not need to compute them every time.  Computation of all static
secondary execution controls is now kept in a single function,
vmx_compute_secondary_exec_control.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We already always set that type but don't check if it is supported. Also
for nVMX, we only support WB for now. Let's just require it.
Signed-off-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Don't use shifts, tag them correctly as EPTP and use better matching
names (PWL vs. GAW).
Signed-off-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

There is currently some confusion between nested and L1 GPAs.  The
assignment to "direct" in kvm_mmu_page_fault tries to fix that, but
it is not enough.  What this patch does is fence off the MMIO cache
completely when using shadow nested page tables, since we have neither
a GVA nor an L1 GPA to put in the cache.  This also allows some
simplifications in kvm_mmu_page_fault and FNAME(page_fault).

The EPT misconfig likewise does not have an L1 GPA to pass to
kvm_io_bus_write, so that must be skipped for guest mode.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
[Changed comment to say "GPAs" instead of "L1's physical addresses", as
 per David's review. - Radim]
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

When a guest causes a page fault which requires emulation, the
vcpu->arch.gpa_available flag is set to indicate that cr2 contains a
valid GPA.

Currently, emulator_read_write_onepage() makes use of gpa_available flag
to avoid a guest page walk for a known MMIO regions. Lets not limit
the gpa_available optimization to just MMIO region. The patch extends
the check to avoid page walk whenever gpa_available flag is set.
Signed-off-by: NBrijesh Singh <brijesh.singh@amd.com>
[Fix EPT=0 according to Wanpeng Li's fix, plus ensure VMX also uses the
 new code. - Paolo]
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
[Moved "ret < 0" to the else brach, as per David's review. - Radim]
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Calling handle_mmio_page_fault() has been unnecessary since commit
e9ee956e ("KVM: x86: MMU: Move handle_mmio_page_fault() call to
kvm_mmu_page_fault()", 2016-02-22).

handle_mmio_page_fault() can now be made static.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Let's reuse the function introduced with eptp switching.

We don't explicitly have to check against enable_ept_ad_bits, as this
is implicitly done when checking against nested_vmx_ept_caps in
valid_ept_address().
Signed-off-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

This is the same as commit 14727754 ("kvm: svm: Add support for
additional SVM NPF error codes", 2016-11-23), but for Intel processors.
In this case, the exit qualification field's bit 8 says whether the
EPT violation occurred while translating the guest's final physical
address or rather while translating the guest page tables.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Reported by syzkaller:

The kvm-intel.unrestricted_guest=0

   WARNING: CPU: 5 PID: 1014 at /home/kernel/data/kvm/arch/x86/kvm//x86.c:7227 kvm_arch_vcpu_ioctl_run+0x38b/0x1be0 [kvm]
   CPU: 5 PID: 1014 Comm: warn_test Tainted: G        W  OE   4.13.0-rc3+ #8
   RIP: 0010:kvm_arch_vcpu_ioctl_run+0x38b/0x1be0 [kvm]
   Call Trace:
    ? put_pid+0x3a/0x50
    ? rcu_read_lock_sched_held+0x79/0x80
    ? kmem_cache_free+0x2f2/0x350
    kvm_vcpu_ioctl+0x340/0x700 [kvm]
    ? kvm_vcpu_ioctl+0x340/0x700 [kvm]
    ? __fget+0xfc/0x210
    do_vfs_ioctl+0xa4/0x6a0
    ? __fget+0x11d/0x210
    SyS_ioctl+0x79/0x90
    entry_SYSCALL_64_fastpath+0x23/0xc2
    ? __this_cpu_preempt_check+0x13/0x20

The syszkaller folks reported a residual mmio emulation request to userspace
due to vm86 fails to emulate inject real mode interrupt(fails to read CS) and
incurs a triple fault. The vCPU returns to userspace with vcpu->mmio_needed == true
and KVM_EXIT_SHUTDOWN exit reason. However, the syszkaller testcase constructs
several threads to launch the same vCPU, the thread which lauch this vCPU after
the thread whichs get the vcpu->mmio_needed == true and KVM_EXIT_SHUTDOWN will
trigger the warning.

   #define _GNU_SOURCE
   #include <pthread.h>
   #include <stdio.h>
   #include <stdlib.h>
   #include <string.h>
   #include <sys/wait.h>
   #include <sys/types.h>
   #include <sys/stat.h>
   #include <sys/mman.h>
   #include <fcntl.h>
   #include <unistd.h>
   #include <linux/kvm.h>
   #include <stdio.h>

   int kvmcpu;
   struct kvm_run *run;

   void* thr(void* arg)
   {
     int res;
     res = ioctl(kvmcpu, KVM_RUN, 0);
     printf("ret1=%d exit_reason=%d suberror=%d\n",
         res, run->exit_reason, run->internal.suberror);
     return 0;
   }

   void test()
   {
     int i, kvm, kvmvm;
     pthread_t th[4];

     kvm = open("/dev/kvm", O_RDWR);
     kvmvm = ioctl(kvm, KVM_CREATE_VM, 0);
     kvmcpu = ioctl(kvmvm, KVM_CREATE_VCPU, 0);
     run = (struct kvm_run*)mmap(0, 4096, PROT_READ|PROT_WRITE, MAP_SHARED, kvmcpu, 0);
     srand(getpid());
     for (i = 0; i < 4; i++) {
       pthread_create(&th[i], 0, thr, 0);
       usleep(rand() % 10000);
     }
     for (i = 0; i < 4; i++)
       pthread_join(th[i], 0);
   }

   int main()
   {
     for (;;) {
       int pid = fork();
       if (pid < 0)
         exit(1);
       if (pid == 0) {
         test();
         exit(0);
       }
       int status;
       while (waitpid(pid, &status, __WALL) != pid) {}
     }
     return 0;
   }

This patch fixes it by resetting the vcpu->mmio_needed once we receive
the triple fault to avoid the residue.
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Tested-by: NDmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

get_cpl requires vcpu_load, so we must cache the result (whether the
vcpu was preempted when its cpl=0) in kvm_vcpu_arch.
Signed-off-by: NLongpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).

But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.

This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted.  kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: NLongpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Add guest_cpuid_clear() and use it instead of kvm_find_cpuid_entry().
Also replace some uses of kvm_find_cpuid_entry() with guest_cpuid_has().
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>