Enabling runtime PM support for davinci mdio driver
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the netpoll function to support netconsole. Tested and works
fine on my "JMC250 PCI Express Gigabit Ethernet Controller" (PCI ID 0250).
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add OF support for the davinci_emac driver.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: netdev@vger.kernel.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatoly Sivov <mm05@mail.ru>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The condition is always true so WOL will never work.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers should pull only ethernet header from page frag
to skb->head.

Pulling 64 bytes is too much for TCP (without options) on IPv4.

However, it makes sense to pull all the frame if it fits the
128 bytes bloc allocated for skb->head, to free one page per
small incoming frame.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: NYan-Pai Chen <yanpai.chen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.

bonding currently disables IFF_XMIT_DST_RELEASE unconditionally.

If all slaves have the IFF_XMIT_DST_RELEASE bit set, then
bonding master can also have it in its priv_flags
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected.  usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.

There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table.  Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: NKevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer FW has added new capability checks for VFs.
Driver should only use those capabilities which are allowed for VFs.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change updates the descriptor macros to accept pointers, updates the
name to drop the _ADV suffix, and include the IXGBEVF name in the macro.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to make the code much more readable for MTQC and MRQC
configuration.

The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
         DCB
         En       Dis
VMDq En  VMDQ/DCB VMDq/RSS
     Dis DCB/RSS  RSS

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.

In this patch I basically did 3 things.  I updated the logic for getting
the first register index.  I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register.  Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues.  By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls.  Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go.  This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.

This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Tested-by: NFrancois Romieu <romieu@fr.zoreil.com>

It's done in very similar way this is done in bonding and bridge.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow).  Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.

On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again.  So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.

In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting.  Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 113952 in Coverity report on Linux.

This is the one instance where we don't, and shouldn't, check the
return code from efx_mcdi_rpc().  It wasn't immediately obvious to me
why we didn't, so I think an explanation is in order.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 102619 in the Coverity report on Linux.

efx_end_loopback() iterates over an array of skb pointers of which
some may be null (if efx_begin_loopback() failed).  It should not use
dev_kfree_skb_irq(), which requires non-null pointers.  In practice
this is safe because it does not run in interrupt context and
therefore always ends up calling dev_kfree_skb(), which does allow
null pointers.  But we should make that explicit.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 113703 in the Coverity report on Linux.

ethtool stats names are limited to 32 bytes including a null
terminator.  Use strlcpy() to ensure that we will always include the
null terminator even if a source string becomes longer than this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

There is nothing in the VLAN driver or core VLAN support that
invalidates the TCP and IP header offsets.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

tso_state::packet_space is always set in tso_start_packet(); the
value set in tso_start() is not used, and is also incorrect.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

With some gcc versions & optimisations, the compiler will warn that
'depth' in efx_filter_insert_filter() may be used without being
initialised, although this is not the case.

This is related to inlining of efx_filter_search(), which only has
one caller since commit 8db182f4
('sfc: Remove now-unused filter function').

Shut the compiler up by initialising it to 0.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The interrupt registers accessed in ixgbevf are more similar to the igb
style registers than they are to the ixgbe style registers.  As such we
would be better off setting up the code for the EICS, EIMS, EICS, EIAM, and
EIAC like we do in igb instead of ixgbe.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the VF driver is processing all of the transmits in interrupt
context.  This can be messy since the Rx is all handled in NAPI and this
may result in interrupts being disabled.  In order to resolve this move all
of the Tx packet processing into NAPI and combine all of the interrupt and
polling routines into just a pair of functions.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For most cases the ixgbevf driver will only ever contain a single Tx and
single Rx queue.  In order to track that it makes more sense to use a
pointer instead of using a bitmap which must be search in order to locate
the ring on an adapter index.  As such I am changing the code to use
pointers and an iterator to access all rings on a given q_vector.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the accounting needed at the start of xmit_frame so
that we can avoid doing too much work to determine how many descriptors we
will need.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch drops the use of eitr_low and eitr_high as values being stored
in the adapter structure.  Since the values have no external way to be
changed they might as well just be hard coded values and save us the space
on the adapter structure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The IXGBE_FLAG_RX_CSUM_ENABLED flag is redundant since NETIF_F_RXCSUM is
keeping the value we want to already have.  As such we can drop the
redundant flag and just make use of NETIF_F_RXCSUM.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no need to keep a separate netdev_registered value since that is
already stored in the netdev itself.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is a large amount of code present in this driver to support features
that either do no exist or are not supported such ask packet split, DCA, or
RSC.  This patch strips out almost all of that code and in the case of
conditionals based on unused flags I am flatting the code out to just the
path that would have been selected.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>