X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.

X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the i40e and i40evf register.h file with the registers for X722.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does the firmware API update to support the new X722 device.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add capabilities flags specific to X722.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding device ids for new hardware X722
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.

NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.

Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up a little confusion in reporting error status in phy and fcoe
setup error reports by separating the return status from the AQ error.

Add two decoder functions to make this easier.

Change-ID: I960bcdeef3978a15fec1cdb5eff781d5cbae42fb
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This driver fully supports VF drivers using both the 1.0 and 1.1
versions of the virtual channel API. However, VF drivers using
version 1.0 get upset if we provide them with a version other than
that, and refuse to play with us.

Correct this by checking the VFs API version at the time that we
store it off, and provide the correct version number back to the VF
so we can all get along.

Change-ID: I86dfe02e67b2bef336b4b49a1bb072f3e7229abc
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store off the PF's API version, then use it to determine whether or not
to send it our capabilities. Change the version checking to allow for PF
drivers with lower API versions than our current version, so we can
still talk to PF drivers over the 1.0 API.

Change-ID: I8edc55d1229c7decf0ed3f285a63032694007c2e
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The most common type of reset that the VF will encounter is a PF reset
that cascades down into a VF reset for each VF. In this case, the VF
will always be assigned the same VSI and recovery is fairly simple.

However, in the case of 'bigger' resets, such as a Core or EMP reset,
when the device is reinitialized, it's probable that the VF will NOT get
the same VSI. When this happens, the VF will not be able to recover, as
it will continue to request resources for its original VSI.

Add an extra state to the admin queue state machine so that the driver
can re-request its configuration information at runtime. During reset
recovery, set this bit in the aq_required field, and fetch the (possibly
new) configuration information before attempting to bring the driver
back up. Since the driver doesn't know what kind of reset it has
encountered, this step is done even for a PF reset, but it doesn't hurt
anything - it just gets the same VSI back.

Change-ID: I915d59ffb40375215117362f4ac7a37811aba748
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store off the VF API version for use when figuring out the VF driver
capabilities. Add support for the VF driver handing its capabilities to
the PF driver and then use this information when sending VF resource
information back to the VF driver.

Change-ID: Ic00d0eeeb5b8118085e12f068ef857089a8f7c2d
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that we've rolled the virtual channel API version to 1.1, add some
macros to test what version is being used by our partner in crime. For the
VF, add some macros to determine what our device capabilities are.

Change-ID: I79f6683d4c23bd76a8ad9fd492776fcc1208e1dc
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To prepare for the changes coming up in the X722 device and future
devices, the virtual channel interface has to change slightly. The VF
driver can now report what its capable of supporting, which then informs
the PF driver when it sends the configuration information back to the
VF.

A 1.1 VF driver on a 1.0 PF driver should not send its capabilities.
Likewise, a 1.1 PF driver controlling a 1.0 VF driver should not expect
or depend upon receiving the VF capabilities.

All other aspects of the API are unchanged.

Change-ID: I530cc55f107edd1ee8bdf95830aa90b87854058a
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NAnjali Singhai <anjali.singhai@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With a little work we can clean up some unnecessary logic jumping and
drop a variable.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Cc: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the switch statement for dynamic interrupt throttling
and adds a default case. With this patch, we check the latency setting
instead of the current ITR settings and the included refactor improves
performance.

Without this patch, the ITR setting would never change dynamically, and
there was no default.

Change-ID: Idb5a8a14c7109ec47c90f6e94bd43baa17d7ee37
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the ARRAY_SIZE macro rather than calculating sizeof(a)/sizeof(a[0]).
Also directly replace the code rather than using an unnecessary define.
Reported-by: NManinder Singh <maninder1.s@samsung.com>
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are many settings possible using ethtool -C/--coalesce, but not
all of them are supported in igb. Report failure when an unsupported
option is set.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver lacks pm_qos_remove_request in error handling (err_req_irq) of
e1000_open, and qos request inserted by pm_qos_add_request is not removed.
This patch add pm_qos_remove_request in error handling to fix it.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the reporting of the RSS key and hash table by
adding support for X550 VFs. The difference is that X550 VFs have
their own registers for RSS key and indirection table, so there is
no need to query the PF.

The RSS key and indirection table are stored in the adapter structure
during the configuration of VFRSSRK and VFRETA which in turn can be
used in ethtool for reporting.

The logic for writing VFRETA is also changed to make sure that the
indirection table is reported correctly.

In addition this patch adds defines for the VFRETA entries and number
of VFRSSRK registers as well as some whitespace cleanups.
Reported-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000_check_for_link_media_swap() checks PHY page 0 for copper and PHY
page 1 for "other" (fiber) link. The switch back from page 1 to page 0
happened too soon, before e1000_check_for_link_82575() is executed, and
link on fiber (other) was never detected. Check for link while still on
the proper PHY page.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For two reasons I want to disable this:
1. Not any part actually check the report status(Alexander Duyck)
2. To report hash value of a packet to stack,
   RSS -> 32bits hash value
   Perfect match fdir filter -> 13bits hash value
   Hashed-based fdir filter -> 31bits hash value

   fdir filter might hash on masked tuples for IP address,
   so it's still not desirable for usage.

So for now, just stick to RSS 32bits hash value.
Signed-off-by: NFan Du <fan.du@intel.com>
Suggested-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set hash type for ingress packets according to NIC
advanced receive descriptors RSS type part.
Signed-off-by: NFan Du <fan.du@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RSS could be leveraged by taking account L4 src/dst ports
as ingredients, thus ingress skb Rx hash type should honor
such the real configuration.
Signed-off-by: NFan Du <fan.du@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change folds the ixgbevf_pull_tail call into ixgbevf_add_rx_frag.  The
advantage to doing this is that the fragment doesn't have to be modified
after it is added to the skb.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we pull the timestamp from the fragment before
we add it to the skb.  By doing this we can avoid a possible issue in which
the fragment can possibly be less than IGB_RX_HDR_LEN due to the timestamp
being pulled after the copybreak check.

While making this change I realized we could also pull the rest of the
igb_pull_tail function into igb_add_rx_frag since in the case of igb,
unlike ixgbe, we are able to unmap the entire buffer before calling
add_rx_frag so merging the two allows for sharing of code between the two
merged functions.
Reported-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: I84573d9fa51effc5b29bf5b8c74e3cc8b2673f48
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change a warning message to indicate what may have really happened when
the init_shared_code call fails.

Change-ID: I616ace40fed120d0dec86dfc91ab2d7cde466904
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e_add_pd_table_entry() routine is being modified to handle both
cases where a backing page is passed and where backing page is allocated
in i40e_add_pd_table_entry().

For PBLE resource management, it is more efficient for it to manage its
backing pages. For VF, PBLE backing page addresses will be send to PF
driver for PBLE resource.

The i40e_remove_pd_bp() is also modified to not free pre-allocated pages and
free only ones which were allocated in i40e_add_pd_table_entry().

Change-ID: Ie673f0403f22979e9406f5a94048dceb91bcf9a8
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During close, all of the MAC filters are cleared, so the driver would be
unable to receive unicast packets after being closed and reopened.

Add the adapter's "hardware" MAC address filter in open, not init. This
ensures that the correct filter is present each time.

Change-ID: I51a11e9c1200139dab6f66a5353bd38c7d26f875
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to an inverted conditional, the driver was marking all of its MAC
filters for deletion every time set_rx_mode was called. Depending upon
the timing of the calls to set_rx_mode and the processing of the admin
queue, the driver would (accidentally) end up with a varying number of
functional filters.

Correct this logic so that MAC filters are added and removed correctly.
Add a check for the driver's "hardware" MAC address so that this filter
doesn't get removed incorrectly.

Change-ID: Ib3e7c4a5b53df6835f164fe44cb778cb71f8aff8
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a VF is disabled, there is no way for it to recover until either
the PF driver is reloaded or SR-IOV is disabled and enabled. To correct
this, enable the VF after a successful reset.

Change-ID: I9e0788476c4d53d5407961b503febdfff2b8a7c6
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF disable code was just whanging on the reset bit without properly
cleaning up the VF, which would leave the VF in an indeterminate state
from which it could not recover. Fix this by notifying the VF and then
by calling the normal VF reset routine.

Change-ID: I862b9dfa919368773cbdc212b805b520db2f7430
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

MAC filters for VFs were being programmed with 0 for the VLAN value when
there was no VLAN assigned. This is incorrect and actually assigns the
VF to VLAN 0. Instead, we must use -1 to indicate that no VLAN is in
use. This change programs the filters correctly and gets rid of a bogus
error message when setting a port VLAN on an active VF.

Change-ID: Ica9a9906d768405377ff3308e27f7d0b5b2ea96e
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make the necessary updates to i40e_adminq_cmd.h.

Change-ID: Ib031c86cc6cab78e5aa44c64d8ce5474be8d7e42
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes some #ifdef's that should not be there. They
were stopping code that is needed from being compiled in.

With these #ifdef's removed, changes are needed in the driver
to fix some compile errors: adding missing parameters to
the definition of ndo_bridge_setlink and a ndo_dflt_brige_getlink call.

Change-ID: I5516614e1bc50b6bca0647cef971bc96161ba2de
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>