Add support for revision 2 of the DViCO FusionHDTV DVB-T Dual Digital 4
which has new tuners and demodulators (2 x DIB7070p). With this patch
both DVB reception and IR works.

The dib7000p driver currently hardwires the output mode to
OUTMODE_MPEG2_SERIAL regardless of what we ask for. Modify it to allow
OUTMODE_MPEG2_PAR_GATED_CLK to be set. Longer term we should remove the
check completely and set the output mode correctly in all the callers.

Add Kconfig bits to ensure the dib7000p and dib0070 modules are enabled.
It would be nice to only do this for the !DVB_FE_CUSTOMISE case, but
this is what the other DIB7070 module does (there are a number of
module dependencies in the attach code).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After commit d9b19199
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NIgor M Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

After adding support for AVerTVHD Volar, DVB_USB_CXUSB must
select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add missing auto-selects for MEDIA_TUNER_XC2028 and DVB_TDA1004X at
dvb-usb/Kconfig.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

$ find linux/drivers/media/dvb -exec grep -l tda827x_attach '{}' \;
linux/drivers/media/dvb/dvb-usb/m920x.c
linux/drivers/media/dvb/ttpci/budget-ci.c
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- select DVB_PLL
- fix typos in comments
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- driver for Anysee DVB-T/C receiver
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

testing of the -tip tree found the following build failures on
2.6.26-rc3:

  drivers/built-in.o: In function `ttusb_dec_disconnect':
  ttusb_dec.c:(.text+0xa2c95): undefined reference to `input_unregister_device'

  drivers/built-in.o: In function `dvb_usb_read_remote_control':
  dvb-usb-remote.c:(.text+0xa6a94): undefined reference to `input_event'

with this config:

  http://redhat.com/~mingo/misc/config-Tue_May_20_03_48_57_CEST_2008.bad

these are due to the media/dvb/usb layer having dependencies on INPUT
functionality, without having that spelled out in the Kconfig file.

this patch makes that dependency explicit (for the drivers affected),
which solves the build error.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since:
1) FW_LOADER is defined as:

config FW_LOADER
        tristate "Userspace firmware loading support"
        depends on HOTPLUG

2) several V4L/DVB driver just selects it;

3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.

So, All drivers that select FW_LOADER should also depend on HOTPLUG.

An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:

drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

namespace for all of them.

Update Kconfig for the hybrid devices recently converted
to use tuner-simple rather than dvb-pll.

dvb-bt8xx no longer uses dvb-pll at all, so remove all
references to dvb-pll within that driver.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This changeset adds support for DiB7070P-based devices by adding the
dib0070-driver and putting the appropriate layouts into
dib0700_devices.c

It also includes a new firmware for the dib0700 which is necessary to
make the DiB7070-boards work and it also should fix the i2c-problems
on some boards.
Signed-off-by: NJean-Philippe Sibers <jpsibers@dibcom.fr>
Signed-off-by: NPatrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add initial support for Dual-DVB-T stick based on DiB7700 and MT2266

- Microtune MT2266 driver.
- Preliminary support for these dual tuner devices :
  - Pinnacle Dual DVB-T diversity
  - Terratec Cinergy DT USB XS diversity
  - Hauppauge Nova TD USB
Signed-off-by: NOlivier DANET <odanet@caramail.com>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch removes all static dependencies on the dvb-pll module.
All exported dvb_pll_desc's have been UNexported, and the caller
will reference the individual dvb_pll_desc by it's index in the
pll_list array.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Acked-by: NOliver Endriss <o.endriss@gmx.de>
Acked-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Marked af9005 driver as experimental and add dependency for qt1010;
Added a dependency on qt1010 in Kconfig;
Corrected the experimental gain  reduction of the mt2060 in case of
strong signal (though it is code included in #ifdef 0).
Signed-off-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for DVB-Opera S1 USB 2.0 BOX.
Signed-off-by: NMarco Gittler <g.marco@freenet.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The code of the dvb-pll driver and the lgh06xf driver is nearly
identical.  The main difference is that the lgh06xf driver would set the
AGC TOP value on every tune call.  The dvb-pll driver now has the ability
to set the AGC TOP when the front-end device is opened, which is a better
way to go about it.  By using this ability of dvb-pll, the lgh06xf driver
is made unnecessary.

There is one other difference.  dvb-pll will probe for the presence of an
I2C pll chip by doing a one byte read, the lgh06xf driver did not do
this.  In some devices the PLL is not reachable over I2C at the timer the
tuner is attached.  Some more initialization, such as firmware loading,
must take place first.  None of the devices using a LG-H06xF should have
this problem.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A number of drivers selected DVB_PLL when they did not need it, and some
that did need it did not select it.

The DVB_PLL option is given a name and help text, so that it will show up
in the config menu.  DVB_PLL support can be turned on if an out-of-tree
driver needs it.

The standard dvb fe customization support is added to dvb-pll.h.  Since
all modules which select DVB_PLL do so unconditionally, it is not
possible to turn dvb-pll off when an enabled module selects it, unlike
most of the other frontend/tuner drivers.  This is because the users of
dvb-pll have static references to dvb-pll symbols other than the attach
function.  If these references are removed, then dvb-pll will be
disablable as the other frontend/tuner drivers are.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds driver for Sigmatek DVB-110 USB DVB-T stick. Stick has based
on hardware of Qtuantek QT1010 tuner, Zarlink ZL10353 (Intel CE 6353)
demodulator and Alcor Micro AU6610 DVB-T USB controller. HW is rather similar
as used in MSI Megasky GL861.
Currently, the driver works only in USB 2.0. In my understanding USB 1.1 is
also supported by hw but I cannot test it due to lack of USB 1.1 port. Device
supports only isochronous mode transfers. There is also eeprom in usb
controller(at least in address range 0x80 - 0xbf) for storing data, eg.
firmware. Anyway, firmware loading is not used / required by the device.
There seems to be at least one unknown I2C device in address 0xa0, probably
remote control or GPIO. Windows drivers reads registers from 0x00 to 0x07
from this unknown address.
Driver is based on gl861 module. Tuner has a lot of problems to lock with
megasky qt1010 module with this hardware with some broadcasting standards.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0
Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs
to be changed. If I read the code correctly setting parallel_ts will
take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead
of 0x03 too. I guess these changes needs to be done only for this
device, not sure how to do that.
The zl10353 changes have been split apart from this patch, into the next
patch, soon to follow.
Signed-off-by: NCarl Lundqvist <comabug@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

update code to use dvb_attach()
update code to reflect recent changes to the dvb_usb framework
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Currently, the driver works in bulk mode supporting both USB 2.0 and
1.0 with and without hardware pid filters.
The ULi m9205 also supports isochronous transfer mode, but I have
dropped support for it because it depends on firmware and does not work
on all USB host chips. Further, I have no firmware with remote
controller support for this mode.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Adding support for Pinnacle PCTV 400e DVB-S. The module name is called ttusb2,
because it this device (and other Pinnacle devices) is using the USB-protocol
originally used by Technotrend device. I'm suspecting Technotrend as the
device-designer.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch creates a new atsc tuner module for the LG TDVS-H06xF ATSC tuners,
called lgh06xf.  The purpose of this change is to reduce some duplicated
code, and to allow the lgh06xf tuner code to take advantage of dvb_attach().
As a side effect, the dependency of dvb-bt8xx on dvb-pll has been removed,
since the lgh06xf module itself will use dvb-pll, while remaining optional
for the dvb-bt8xx driver through the use of DVB_FE_CUSTOMISE
Acked-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch contains support for the DiB7000PC-driver.
Signed-off-by: NFrancois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: NPatrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Initial commit for the driver for the DiB7000M COFDM demodulator.
Signed-off-by: NFrancois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: NPatrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Let the MT2060 be customized like most of the other DVB PLLs/front-ends. 
Also, add a missing dependency on I2C.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support for DiB7000M frontend were not included on 2.6.19, since still not
completed. Removing Kconfig item.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Several fixes for dib0700-module. (Firmware error checking, dependency)
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch is the first commit of the Multiple Input Patch for the DVB-USB frame
work.
It changes the DVB-USB-device to be able to have more than one streaming input
(e.g. multiple DVB-T sources) on one device. This is a necessary feature for
the upcoming DiB7700 driven devices.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some minor code cleanups and added the MT2060 to new v4l-dvb-build-system, preliminarily under dvb/frontends.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Several DVB modules depends on I2C
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for a newer version of this device
using the zl10353 frontend instead of the mt352 frontend.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>