As the NIC PCI function may be used by other protocols, the chip interrupts
must be enabled in be_probe() itself rather than be_open().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows LRO aggregation on bonded devices that contain an
NX3031 device. It also adds a for_each_netdev_in_bond_rcu(bond, slave)
macro which executes for each slave that has bond as master.

V3: After testing and discussing this with Rajesh, I decided to keep the
    vlan ip cache and just rename it to ip_cache since it will store bond
    ip addresses too. A new master flag has been added to the ip cache to
    denote that the address has been added because of a master device.
    I've taken care of the enslave/release cases by checking for various
    combinations of events and flags (e.g. netxen has a master, it's a
    bond master and it's not marked as a slave means it is being enslaved
    and is dev_open()ed in bond_enslave).
    I've changed netxen_free_ip_list() to have a "master" parameter which
    causes all IP addresses marked as master to be deleted (used when a
    netxen is being released). I've made the patch use the new upper
    device API as well. The following cases were tested:
    - bond -> netxen
    - vlan -> netxen
    - vlan -> bond -> netxen

V2: Remove local ip caching, retrieve addresses dynamically and
    restore them if necessary.

Note: Tested with NX3031 adapter.
Tested-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAndy Gospodarek <agospoda@redhat.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It enables direct DMA by HW to memory region PBL arrays and fast register PBL
arrays from host memory, vs the T4 way of passing these arrays in the WR itself.
The result is lower latency for memory registration, and larger PBL array
support for fast register operations.

This patch also updates ULP_TX_MEM_WRITE command fields for T5. Ordering bit of
ULP_TX_MEM_WRITE is at bit position 22 in T5 and at 23 in T4.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All T5 adapters will only support VFs on PF0-3 despite the ability of the
hardware to support them on PF4-7.  This keeps our T4 and T5 adapters more
similar which simplifies host driver software.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements a low latency Write Combining (aka Write Coalescing) work
request path. PCIE maps User Space Doorbell BAR2 region writes to the new
interface to SGE. SGE pulls a new message from PCIE new interface and if its a
coalesced write work request then pushes it for processing. This patch copies
coalesced work request to memory mapped BAR2 space.
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable dev is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QLogic applications use these callbacks to perform

o  NIC Partitioning (NPAR) configuration and management
o  Diagnostic tests
o  Flash access and updates
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.

CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement to collect ethernet statistical information on ks8851_mll device.
Signed-off-by: NDavid J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: NMichael Stapelberg <michael@stapelberg.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: NMichael Stapelberg <michael@stapelberg.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI header is not needed, so get rid of it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using list_move() instead of list_del() + list_add().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x FW 1.78.17 properly supports DCBX configuration for 4-port devices,
enabling FCoE support on 57840 boards.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update appropriate HSI files and adapt driver accordingly.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Support sysfs interface for getting the maximal number of virtual functions
   of a given physical function.
2. Support sysfs interface for getting and setting the current number of
   virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.

This patch prevents said message.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>