Changeset in MPI 2.0 Rev V(2.0.14) specification

        1) Bumped MPI2_HEADER_VERSION_UNIT.
        2) Added a product specific range to event values.
        3) Added clarification to Direct-Attached SAS PHY Power condition.
        4) Updated timing requirements for performing Hard Reset.
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When specifying the command line option "max_sectors" less than 64, then
warning message should provide correct upper boundary value 32767 instead of
8192.
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

A new sysfs shost attribute called "BMR_status" is implemented to
report Backup Rail Monitor status.

This attribute is located in the path
        /sys/class/scsi_host/host#/BMR_status

when reading this adapter attribute, then driver will output the state
of GPIO[24]. It returns "0" if BMR is healthy and it returns "1" for failure.

if it returns an empty string then it means that there was an error while
obtaining the BMR status. Then check dmesg for what error has occured.
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Updating the customer branding string for "SSD 910 Series" controller
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The Copyright String in all the drivers sources were changed to 2012
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.

This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id().
This is because smp_processor_id() is not called in preempt safe condition.

To fix this issue, use raw_smp_processor_id instead of smp_processor_id.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When scsi_add_host fails the scsi_host_put should be called.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The ioc->pfacts member in the IOC structure is getting set to zero
following a call to _base_get_ioc_facts due to the memset in that routine.
So if the ioc->pfacts was read after a host reset, there would be a NULL
pointer dereference. The routine _base_get_ioc_facts is called from context
of host reset.  The problem in _base_get_ioc_facts  is the size of
Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60,
so there is a four byte overflow resulting from the memset.

Also, there is memset in _base_get_port_facts using the incorrect structure,
it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Fix for hard drive going OFFLINE when hard reset issued and simultaneously another hard drive is hot unplugged

Following the host reset, the firmware discovery is reassigning another hard
drive in the topology to the same device handle as that device is getting hot
removed. Until the driver device removal routine is called, there will be two
hard drive with the matching device handle in the internal device link
list. In the device removal routine, a separate function which moves the
device from BLOCKED into OFFLINE state.  Since this routine is passed with the
device handle passed as input parameter, the routine will be traversing the
internal device link list searching for matching device handle. This results
in two devices with matching device handle, therefore both devices goes
OFFLINE.

To fix this issue,the input parameter is changed from device handle to SAS
address, therefore only the device that is hot unplugged will be placed in
OFFLINE state.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Set the phy identifier of the end device to the phy number of the parent device it is linked to

The phy_identifier inside the routine _transport_set_identify()
is set to sas_device_page_zero->PhyNum. This returns the
phy number of the parent device this device is linked to.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas : While enabling phy, read the current port number from sas iounit page 0 instead of page 1

The port number is changing after disabling/enabling phys using the SysFS
interface This is because the firmware behavour changed where it would read
the the port number then set it to some different value even though Auto Port
Config is turned on.  With this change of behavour in FW, it is possible that
the expanders are moved from one port to another after disabling /enabling
phys. This is occuring because the port number in sas iounit page 1 is not
matching up to the current port in page 0. In order to fix this the driver is
modified to read the current port number from sas iounit page 0 instead of
page 1.  Also copy the port and phy flags over from page 0 to page 1.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix several endian issues found by runing sparse.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Modified the source code as per the findings reported by the source
code analysis tool. Source code for the following functionalities
has been touched. None of the driver functionalities has changed.

- SMP Passthrough IOCTL
- Debug messages for MPT Replies (i.e. bit 9 of Logging Level)
- Task Management using sysfs
- Device removal, i.e. when a target device (including any PD within a volume)
  is removed, and Volume Deletion.
- Trace Buffer
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Improvement were made to better protect the sas_device, raid_device, and expander_device lists

There were possible race conditions surrounding reading an object
from the link list while from another context in the driver was
removing it. The nature of this enhancement is to rearrange locking
so the link lists are better protected.

Change set:
(1) numerous routines were rearranged so spin locks are held through
the entire time a link list object is being read from or written to.
(2) added new routines for object deletion from link list.  Thus ensuring
lock was held during the deletion of the link list object, then and memory
for object freed outside the lock. The memory was freed outside the lock
so driver had access to device object info which was required for
notifying the scsi mid layer that a device was getting deleted.
(3) added the ioc->blocking_handles parameter.  This is a bitmask used
to identify which devices need blocking when there is device loss.  This was
introduced so that lock can be held for the entire time traversing the link
list objects, and the bitmask was set to indicate which device handles need
blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed,
with the respective device handle the scsi mid layer is called for moving
devices into blocking state.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas : Perform Target Reset instead of HBA reset when a SATA_PASSTHROUGH cmd timeout happens
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added support for Block IO requests with multiple segments (vectors) in
the SMP handler of the SAS Transport Class. This is required by the
BSG driver. Multisegment support added for both, Request and Response.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When the lock_kernel and unlock_kernel routines were removed in the
2.6.39 kernel, a global mutex was added on top of the existing mutex
which already existed. With this implementation, only one IOCTL
will be active at any time no matter how many ever controllers
are present. This causes poor performance.

Removed the global mutex so that the driver can work with the existing
semaphore that was already part of the existing code.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Changeset in MPI headers:
1) Bumped MPI2_HEADER_VERSION_UNIT
2) Added 4K sectors supported bit to CapabilitiesFlags field of IOC Page 6.
3) Added UEFIVersion field to BIOS Page 1 and defined additional
    BiosOptions bits to control UEFI behavior.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

commit 44c10138 (PCI: Change all
drivers to use pci_device->revision) converted all drivers to use
pci_dev->revision.  Convert these three drivers which got missed.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fix ensures that the IOP_LOGINFO_CODE_TASK_TERMINATED
messages do not clutter the sas_log_info messages.

Bugzilla 42142 - mpt2sas: Number specified in wrong base
https://bugzilla.kernel.org/show_bug.cgi?id=42142Signed-off-by: NSathisha Nanjappa <sathisha.nanjappa@hp.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The old pci_remove_bus_device actually did stop and remove.

Make the name reflect that to reduce confusion.

This patch is done by sed scripts and changes back some incorrect
__pci_remove_bus_device changes.
Suggested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The __get_free_pages can fail, so the return value should be checked.
Spotted thanks to Stanislaw.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.

The patch fixes the issue by jumping afer mutex_unlock() call.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Correct spelling "mappping" to "mapping"
in drivers/scsi/mpt2sas/mpt2sas_config.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Removed redundant calling of _scsih_probe_devices() from _scsih_probe as
it is getting called from _scsih_scan_finished.

Also moved the function scsi_scan_host(shost) to get called after the
volumes on warp drive are reported to the OS. Otherwise by the time
the (ioc->hide_drives) flags is set, the volumes on warp drive
are reported to the OS already.

Also modified the initialization of reply queues only in case of driver load
time in the function _base_make_ioc_operational().
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 921cd802 ("[SCSI] mpt2sas: New feature - Fast Load
Support") moved handling of the diag_buffer_enable module parameter
from mpt2sas_base.c to mpt2sas_scsih.c, but it left an old copy of the
parameter in mpt2sas_base.c.  Remove the unused stub.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When computing reply_queue_count (the number of MSI-X vectors to use),
the driver does

	ioc->reply_queue_count = min_t(u8, ioc->cpu_count,
	    ioc->msix_vector_count);

However, on a big machine, ioc->cpu_count could be outside the range
that fits in a u8; eg a system with 256 CPUs will end up
reply_queue_count set to 0.

Fix this by calculating the minimum as ints and then letting the
assignment to reply_queue_count handle integer demotion.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 911ae943 ("[SCSI] mpt2sas: Added NUNA IO support in driver
which uses multi-reply queue support of the HBA") added new
allocations to the beginning of mpt2sas_base_attach(), which means
directly returning an error on failure of mpt2sas_base_map_resources()
will leak those allocations.

Fix this by doing "goto out_free_resources" in this place too, as the
rest of the function does.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Bump driver vesion to 12.100.00.00
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The amount of memory required for tracking chain buffers is rather
large, and when the host credit count is big, memory allocation
failure occurs inside __get_free_pages.

The fix is to limit the number of chains to 100,000.  In addition,
the number of host credits is limited to 30,000 IOs. However this
limitation can be overridden this using the command line option
max_queue_depth.  The algorithm for calculating the
reply_post_queue_depth is changed so that it is equal to
(reply_free_queue_depth + 16), previously it was (reply_free_queue_depth * 2).
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When an I/O request to a WarpDrive is timed out by SML and if the
I/O request to the WarpDrive is sent as direct I/O then the aborted
direct I/O will be retried as normal Volume I/O and which results
in failure of Target Reset and results in host reset.

The fix is to not retry a failed IO to volume when the original
IO was sent as direct IO with an ioc status
MPI2_IOCSTATUS_SCSI_TASK_TERMINATED.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added code to release the spinlock that is used to protect the
raid device list before calling a function that can block. The
blocking was causing a reschedule, and subsequently it is tried
to acquire the same lock, resulting in a panic (NMI Watchdog
detecting a CPU lockup).
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

1)Removed Power Management Control option for PCIe link.
2)Added RAID Action for performing a compatibility check. Added
product-specific range to RAID Action values.
3)Added PhysicalPort field to SAS Device Status Change Event data.
4)Added SpinupFlags field containing a Disable Spin-up bit to the
SpinupGroupParameters fields of SAS IO Unit Page 4.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Increase max transfer support from 4MB to 16MB.
This is done by changing the shost->max_sector from 8192 to 32767
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The driver is modified to allow access to the greater than 2TB WarpDrive
and properly handle direct-io mapping for WarpDrive volumes greater than 2TB.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>