The ASPM workaround setting obtained from NVRAM only works with devices
older than 5717.  This patch enforces the restriction.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the code to only manage the PCIe gphy power for
CPMU-less devices only.  The CPMU takes over management for newer
chips.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy test register location has been repurposed for 5717+ devices.
This patch changes the code to avoid this location for these devices.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch creates a TG3_FLG3_5717_PLUS flag to collectively describe
the set of changes in the ASIC that will apply to all future chip
revisions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TSS flag needs to be turned off during tg3_close().  If the device
fails to allocate more than one MSI-X vector the next time the device is
brought up, transmits will fail.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3 commit e7126997 entitled
"tg3: Preserve PCIe MPS setting for new devs" attempted to ensure the
PCIe link negotiated Maximum Payload Size (MPS) setting was 128 bytes
for all devices that didn't support higher speeds.  The 5784 device was
mistakenly added to this list when it shouldn't have.  This patch
removes the 5784 ASIC rev devices from that list.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use skb->len for accounting as xt_quota does. Since nf_conntrack works
at the network layer, skb_network_offset should always returns ZERO.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

The tuple got from unique_tuple() doesn't need to be really unique, so the
check for the unique tuple isn't necessary, when there isn't any other
choice. Eliminating the unnecessary nf_nat_used_tuple() can save some CPU
cycles too.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

The only user of unique_tuple() get_unique_tuple() doesn't care about the
return value of unique_tuple(), so make unique_tuple() return void (nothing).
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Use local variable hdrlen instead of ip_hdrlen(skb).
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

This removes duplicate code by providing a default implementation
which is used by 3 of the 4 modules that provide these call.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

IPVS was merged into the kernel quite a long time ago and
has been seeing wide-spread production use for even longer.

It seems appropriate for it to be no longer tagged as EXPERIMENTAL

Signed-off-as: Simon Horman <horms@verge.net.au>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

some users of nf_ct_ext_exist() know ct->ext isn't NULL. For these users, the
check for ct->ext isn't necessary, the function __nf_ct_ext_exist() can be
used instead.

the type of the return value of nf_ct_ext_exist() is changed to bool.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

We currently disable BH for the whole duration of get_counters()

On machines with a lot of cpus and large tables, this might be too long.

We can disable preemption during the whole function, and disable BH only
while fetching counters for the current cpu.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

If user misconfigures ingress and causes a redirection loop, don't
overwhelm the log.  This is also a error case so make it unlikely.
Found by inspection, luckily not in real system.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The other calls to kmalloc in the same function use GFP_ATOMIC, and indeed
two locks are held within the body of the function.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ identifier f; @@

*f(...,GFP_ATOMIC,...)
... when != spin_unlock(...)
    when != read_unlock(...)
    when != write_unlock(...)
    when != read_unlock_irq(...)
    when != write_unlock_irq(...)
    when != read_unlock_irqrestore(...)
    when != write_unlock_irqrestore(...)
    when != spin_unlock_irq(...)
    when != spin_unlock_irqrestore(...)
*f(...,GFP_KERNEL,...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GET_STATS request uses the same memory region as the response.
If a new request for get stats is fired before the response for
the previous get_stats request is received, the response will
corrupt the new request, causing the f/w to misbehave.
Signed-off-by: NSomnath K <somnathk@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

link status is wrongly displayed under certain circumstances.
This change fixes it.
Signed-off-by: NSomnath K <somnathk@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when the BE device becomes unresponsive, dump the registers to help debugging
Signed-off-by: NSomnath K <somnathk@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move be_check_sriov_fn_type to appropriate place to correctly determine
if the be2net driver needs to work as a VF driver or a PF driver.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix selected style problems reported by checkpatch.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAC modules control registers vary as per the version of the
EMAC module. EMAC_CTRL_EWCTL,EMAC_CTRL_EWINTTCNT are available
only on EMAC_VERSION_1. The emac_dump_regs() function accesses
these indiscriminately. This patch fixes the issue.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of NAPI poll function in the driver does not service
Rx packets, error condition even if a single Tx packet gets serviced in
the napi poll call. This behavior severely affects performance for specific use
cases. This patch modifies the poll function implementation to service tx/rx
packets in an identical manner.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DaVinci EMAC module includes an interrupt pacing block that can
be programmed to throttle the rate at which interrupts are
generated. This patch implements interrupt pacing logic that can
be controlled through the ethtool interface(only rx_coalesce_usecs
param is honored)
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently you cannot disable multicast snooping while a device is
down.  There is no good reason for this restriction and this patch
removes it.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were two problems here.  We returned success if dnet_mii_init()
failed and there was a release_mem_region() missing.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using module options arp monitoring and balance-alb/balance-tlb
are mutually exclusive options.  Anytime balance-alb/balance-tlb are
enabled mii monitoring is forced to 100ms if not set.  When configuring
via sysfs no checking is currently done.

Handling these cases with sysfs has to be done a bit differently because
we do not have all configuration information available at once.  This
patch will not allow a mode change to balance-alb/balance-tlb if
arp_interval is already non-zero.  It will also not allow the user to
set a non-zero arp_interval value if the mode is already set to
balance-alb/balance-tlb.  They are still mutually exclusive on a
first-come, first serve basis.

Tested with initscripts on Fedora and manual setting via sysfs.
Signed-off-by: NAndy Gospodarek <gospo@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use pr_fmt, pr_<level> and netdev_<level> where appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ks8842 uses dma channel functions, so it should depend on DMA_ENGINE.

ERROR: "__dma_request_channel" [drivers/net/ks8842.ko] undefined!
ERROR: "dma_release_channel" [drivers/net/ks8842.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains a fix for UCC device number in verbose debug message.
Signed-off-by: NSergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, only ethtool can get accurate link state of a tap device.
With this patch, IFF_RUNNING and IF_OPER_UP/DOWN are kept up to date as
well.
Signed-off-by: NNolan Leake <nolan@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem

Cc: Joe Perches <joe@perches.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some features require knowing the DTIM period
before associating. This implements the ability
to wait for a beacon in mac80211 before assoc
to provide this value. It is optional since
most likely not all drivers will need this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix possible double priv->mutex lock introduced by commit
a69b03e9
"iwlwifi: cancel scan watchdog in iwl_bg_abort_scan" .
We can not call cancel_delayed_work_sync(&priv->scan_check) with
priv->mutex locked because workqueue function iwl_bg_scan_check()
take that lock internally.

We do not need to synchronize when canceling priv->scan_check work.
We can avoid races (sending double abort command or send no
command at all) using STATUS_SCAN_ABORT bit. Moreover
current iwl_bg_scan_check() code seems to be broken, as
we should not send abort commands when currently aborting.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 8366 AP support in particular is still rather incomplete, but
this is unlikely to be addressed any time soon.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes the information available through ethtool...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>

This makes the information available through ethtool...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NKalle Valo <kvalo@adurom.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>