This patch adds needed nodes and properties to support suspend/resume
on the MPC8610HPCD boards.

There is a dedicated switch (SW9) that is used to wake up the boards.
By default the SW9 button is routed to IRQ8, but could be re-routed
(via PIXIS) to sreset.

With 'no_console_suspend' kernel command line argument specified, the
board is also able to wakeup upon serial port input.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com> [dts]
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- Add power management controller nodes;
- Add interrupts for RTC nodes, the RTC interrupt may be used as a
  wakeup source;
- Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds suspend/resume support for MPC8540 and MPC8641D-
compatible CPUs. To reach sleep state, we just write the SLP bit
into the PM control and status register.

So far we don't support Deep Sleep mode as found in newer MPC85xx
CPUs (i.e. MPC8536). It can be relatively easy implemented though,
and for it we reserve 'mem' suspend type.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

So far the driver is used to reset QE upon resume, which is needed on
85xx. Later we can move some QE initialization steps into probe().
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is needed to avoid ugly #ifdefs in drivers. Also update fsl_qe_udc
driver so that now it doesn't define its own versions that cause build
breakage when the generic stubs are used.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The bits are generic to CPM devices, so let's move them to the
common header file, so drivers won't need to privately reintroduce
another bunch of the same bits (as we can't include cpm2.h header
together with cpm1.h).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

struct mcc defined in both immap_qe.h and immap_cpm2.h, so they will
conflic when included in a single file. The mcc struct is easy to deal
with, since it isn't used in any driver (yet), so let's just rename QE
version to qe_mcc.

The ucb_ctlr is a bit trickier, since it is used by fsl_qe_udc driver,
and the driver supports both CPM and QE UDCs, plus the QE version is
used to form a bigger immap struct.

I don't want to touch too much of USB code in this series, so for now
let's just copy most generic version into the common cpm.h header,
later we'll create cpm_usb.h where we'll place common USB structs that
are used by QE/CPM UDC and QE Host drivers (FHCI).

And as for the structs in qe.h and cpm2.h, just prefix them with qe_
and cpm_.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

When cpm2.h included into spi_mpc8xxx driver, the SPI defines
in the header conflict with defines in the driver.

We don't need them in the header file, so remove them. Plus
remove "struct spi", we'll use a better version in the driver.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1020 is another member of Freescale QorIQ series of processors.
It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences from P2020:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities(new controller).

From board perspective P1020RDB is same as P2020RDB.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

It appears that QE shuts down on all MPC85xx CPUs (i.e. MPC8568 and
MPC8569) and thus needs reset upon resume.

So modify qe_alive_during_sleep() to account that.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

For MPC8569 CPUs we'll need to reset QE after each suspend, so make
qe_reset() code path suitable for repeated invocation, that is:

- Don't initialize rheap structures if already initialized;
- Don't allocate muram for SDMA if already allocated, just reinitialize
  registers with previously allocated muram offset;
- Remove __init attributes from qe_reset() and cpm_muram_init();
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch creates the dts files for each core and splits the devices
between the two cores for P2020RDB.

core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto,
		global-util, pci0,
core1 has L2, dma2, eth0, pci1, msi.

MPIC is shared between two cores but each core will protect its
interrupts from other core by using "protected-sources" of mpic.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is needed to avoid #ifdefs in MPC85xx suspend/resume code.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

MPC8569 CPUs have four QE RISCs, so we need to increase MAX_QE_RISC
constant, otherwise qe_upload_firmware() fails at sanity checking.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

pasemi_defconfig hasn't been updated for a year.

Mostly a refresh of defaults, but this also disables 64K pages.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Updated mpc85xx_{smp_}defconfig to enable:
* XES_MPC85xx board
* PCI MSI
* RapidIO
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

u-boot partition size should be 0x80000 (512 KB), not 0x8000 (32 KB).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.

This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: NLiu Yu <Yu.Liu@freescale.com>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Prevent NULL dereference if kmalloc() fails. Also clean up if
of_mdiobus_register() returns an error.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e.  Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board.  This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).

This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.

With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Patch f598282f exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.

The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Doing so causes xtime to be negative which crashes the timekeeping
code in funny ways when doing suspend/resume
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Following S390's good example we should use hrtimers for the decrementer too!
This patch converts the timer from the old mechanism to hrtimers.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It looks like the variable "pc" is defined. At least the current code always
failed on me stating that "pc" is already defined somewhere else.

Let's use _pc instead, because that doesn't collide.

Is this the right approach? Does it break on 440 too? If not, why not?
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Now we have everything in place to be able to build KVM, so let's add it
as config option and in the Makefile.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In order to access fields in the PACA from assembly code, we need
to generate offsets using asm-offsets.c.

So let's add the new PACA related bits, we just introduced!
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For KVM we need to store some information in the PACA, so we
need to extend it.

This patch adds KVM SLB shadow related entries to the PACA and
a field that indicates if we're inside a guest.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

To be able to keep KVM as module, we need to export the SLB trampoline
addresses to the module, so it knows where to jump to.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For KVM we need to allocate a new context id, but don't really care about
all the mm context around it.

So let's split the alloc and destroy functions for the context id, so we can
grab one without allocating an mm context.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We want to be able to build KVM as a module. To enable us doing so, we
need some more exports from core Linux parts.

This patch exports all functions and variables that are required for KVM.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to access some VCPU fields from assembly code. In order to get
the proper offsets, we have to define them in asm-offsets.c.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to run some KVM trampoline code in real mode. Unfortunately, real mode
only covers 8MB on Cell so we need to squeeze ourselves as low as possible.

Also, we need to trap interrupts to get us back from guest state to host state
without telling Linux about it.

This patch adds interrupt traps and includes the KVM code that requires real
mode in the real mode parts of Linux.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Little opcodes behave differently on desktop and embedded PowerPC cores.
In order to reflect those differences, let's add some #ifdef code to emulate.c.

We could probably also handle them in the core specific emulation files, but I
would prefer to reuse as much code as possible.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We support setting the DEC to a certain value right now. Doing that basically
triggers the CPU local timer.

But there's also an mfdec command that enabled the OS to read the decrementor.

This is required at least by all desktop and server PowerPC Linux kernels. It
can't really hurt to allow embedded ones to do it as well though.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are generic parts of PowerPC that can be shared across all
implementations and specific parts that only apply to BookE or desktop PPCs.

This patch adds emulation for desktop specific opcodes that don't apply
to BookE CPUs.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds an implementation for a G3/G4 MMU, so we can run G3 and
G4 guests in KVM on Book3s_64.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>