Update the magic values of the wl1271 boot time config according to the new
reference driver.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the change to the new firmware, there was a change to firmware memory
partitioning. Along with that change, the translation of all partitions was
unified, and separate functions for reg and mem access became unnecessary.

Cleanup the unnecessary functions.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the TX path block calculation algorithm based on TI reference.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable and configure smart reflex. This should have a reducing impact on
power consumption.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new firmware has fixed a firmware crash problem related to ELP entry.
Enable ELP to conserve power.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove separate interrupt register reading from the interrupt handling
routine. This will slightly improve interrupt performance.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Updated RefClk configuration based on reference sources. Apparently this
change will improve RF performance.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add top register access function.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove RX workaround which is not needed with newer firmware revisions. This
will reduce one SPI register transaction per RX packet.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the memory regions and memory mapping to support firmware revision
6.1.0.0.241.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to listen to HW_AVAILABLE interrupts when using ELP with firmware
revision 6.1.0.0.241.  Add WL1271_ACX_INTR_HW_AVAILABLE to the interrupts that
are enabled by default.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We still don't have proper calibration for our devices, so we are using way
too much power for TX, which causes a lot of distortion.  This hack hardcodes
the txpower to 7dBm.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't get any indication from the stack when we have disassociated.  In
wl1271, it is important to send a CMD_DISCONNECT before joining again,
because the firmware cleans some things up.  So we check if we're already
joined and disconnect if that's the case.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements the CMD_DISCONNECT command, which should be sent to the
firmware when we are disassociated.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Channel switch host command has different data structure for
different devices. Adding additional structures to support 5000 and 6000
NICs. unlike 4965, starting with 5000 series, the tx power is managed by
uCode, there is no tx power db information need to be passing from driver to
uCode; but the space needs to be reserved to match uCode expection.

1000 NIC do not support channel switch operation since it is 'bgn'
device, there is no need to have data structure defined for it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rearrange the code and groups setting of
retry_limit and data_retry_limits code together.
Make 'data_retry_limit' setting similar to iwlwifi
for better readability.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the ununsed variable data_retry_limit
from priv.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename iwl3945_tx_cmd variable tx to tx_cmd for better
readability.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 and 4965 share the functionality for setting RTS and CTS to
the tx_cmd. Unify these functions and move the common
functionality to core.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding accumulative statistics counters in iwlwifi driver.
Statistics counters are reported by uCode every beacon interval; but can
be reset by uCode when needed. The accumulative statistics counters is
maintained by driver to keep track of the history of all the counters.

Update the ucode stats files in debugfs to display both latest and
accumulative counters.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_power_initialize() initializes driver data (not device hardware), and does
not need to execute more than once (when the driver initializes).  Therefore, it
does not belong in iwl3945_apm_init(), which initializes hardware, and may run
more than once.

Move it to iwl3945_pci_probe(), where it will run only once.  This agrees
with similar placement in iwl-agn.c's iwl_pci_probe(), although placement
under "services" seemed more appropriate than under "mac80211".
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl3945_rfkill_poll() has been silently calling wiphy_rfkill_set_hw_state()
every 2 seconds, regardless of whether hardware RF KILL switch changed state.

Call wiphy_rfkill_set_hw_state() only when RFKILL switch changes.
Add IWL_DEBUG_RF_KILL log message and documentation.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sleep_level_override debugfs file is used by the user to request a
static power index instead of the dynamic sleep values. Users are expected
to provide value from 1 to 5 as an index or -1 to disable it.

The problem at the moment is that users can also provide 0 to this file
which, together with the value 1, is translated to index 1. This is
confusing and even more so when users write 0 to sleep_level_override and
then read 1 from it afterwards.

Modify checking to treat 0 as invalid.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add more items to sensitivity range table to avoid using hardcoded values.
Initialize the table per device since unique per device information is
required to perform sensitivity calibration.

additional items in sensitivity range table:
   .barker_corr_th_min: Barker correlation threshold minimum
   .barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC
   .nrg_th_cca: Energy threshold for Clear Channel Assessment

Barker codes are a technique used in WLAN encoding for transmission.
MRC is "Maximal Ratio Combining", a technique for optimally combining the
signals from 2 or more receivers to achieve a better signal.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"IWL_CMD_QUEUE_NUM" is being defined in multiple places and used by all
the devices. move it to iwl-dev.h file and shared by all the devices.

Remove "IWL_CMD_FIFO_NUM", replaced by "IWL49_CMD_FIFO_NUM" and IWL50_CMD_FIFO_NUM"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up device-specific apm_reset() functions and library infrastructure,
now that these reset() functions are no longer being used.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we're unconditionally using apm_ops.stop() to reset and power-down
the device in __iwl3945_down(), the apm_ops.reset() is redundant.  Removing
this call will also allow us to remove iwl3945_apm_reset().

Remove unneeded iwl_clear_bit(CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ) because
this bit will be set again very soon in iwl3945_hw_txq_ctx_stop() and other
following calls.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user
no longer wants device active), device has not been going into low power state
via __iwl_down().  apm_ops.reset() does not put device into low power state;
instead it resets the device, then puts it into a powered-up state ready to be
re-loaded with uCode and re-started.  This has needlessly warmed up user's
laptops and drained batteries.

With current architecture in which mac80211 controls device up/down (including
resetting device after firmware errors), there is no need for apm_ops.reset()
any more; apm_ops.reset() is basically a combination of apm_ops.stop() and
apm_ops.init().

Instead, __iwl_down() now unconditionally places the device into a low-power
state via apm_ops.stop(). Device may be re-started via __iwl_up() calling
apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors),
but in the meantime, device will stop wasting energy.

Note that, even in this low power state, if driver re-enables interrupts,
the device retains the ability to sense the hardware RF-KILL switch, and
(except for 3945) interrupt the host when it changes.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update iwl3945_apm_init() to set up device registers in sequence most recently
recommended by factory.

Add resets for APMG interrupts and radio chip, formerly done only in
iwl3945_apm_reset(); moving them here assures that apm_init() will do
a complete job of preparing hardware not only after platform boot,
but also after apm_stop() has executed (due to rfkill, ifconfig down,
driver unload, etc.).  This is in preparation to completely remove apm_reset().

Add some comments.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some airo card don't support power Management [1].
Don't abort suspend with those cards.

00:06.0 Network controller: AIRONET Wireless Communications PC4800 (rev 01)
        Flags: medium devsel, IRQ 17
        Memory at dffffe00 (32-bit, non-prefetchable) [size=128]
        I/O ports at d000 [size=128]
        I/O ports at cc00 [size=64]
        Kernel driver in use: airo
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We must check the bustype before using the host_pci pointer.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX is hung, the chip is reset. Ensure that
the chip is awake by using the PS wrappers.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return status of lbs_prepare_and_send_command and lbs_cmd_with_response
functions is not checked at some places. Those checks are added.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently several events are enabled from the firmware for which there
is no handling. This wakes up the host unnecessarily. Mask those
unneeded events.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable beacon filtering when PSM is enabled
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable beacon filtering with the mac80211 stack.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use vmalloc to allocate memory for the firmware image, and use a smaller
linear buffer for the actual transfer of the firmware to the chipset.

This patch is an adaptation of a similar patch for wl1251 by Kalle Valo.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable multicast filtering. This way by default no multicast frames will
reach the host, and when needed, only required multicast frames can be
passed from the WLAN chipset to the host.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>