This patch basically allows any HBA attached to the SPI transport class
to declare an extra area which the mid-layer will allocate as part of
its device and target allocations.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This gives the HBA driver notice when a target is created and
destroyed to allow it to manage its own target based allocations
accordingly.

This is a much reduced verson of the original patch sent in by
James.Smart@Emulex.com
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

	a) TYPE_SDAD renamed to TYPE_RBC and taken to scsi.h
	b) in sbp2.c remapping of TYPE_RPB to TYPE_DISK turned off
	c) relevant places in midlayer and sd.c taught to accept TYPE_RBC
	d) sd.c::sd_read_cache_type() looks into page 6 when dealing with
TYPE_RBC - these guys have writeback cache flag there and are not guaranteed
to have page 8 at all.
	e) sd_read_cache_type() got an extra sanity check - it checks that
it got the page it asked for before using its contents.  And screams if
mismatch had happened.  Rationale: there are broken devices out there that
are "helpful" enough to go for "I don't have a page you've asked for, here,
have another one".  For example, PL3507 had been caught doing just that...
	f) sbp2 sets sdev->use_10_for_rw and sdev->use_10_for_ms instead
of bothering to remap READ6/WRITE6/MOD_SENSE, so most of the conversions
in there are gone now.

	Incidentally, I wonder if USB storage devices that have no
mode page 8 are simply RBC ones.  I haven't touched that, but it might
be interesting to check...
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There's a basic need not to have parameters go under or over certain
values when doing domain validation.  The basic ones are

max_offset, max_width and min_period

This patch makes the transport class take and enforce these three
limits.  Currently they can be set by the user, although they could
obviously be read from the HBA's on-board NVRAM area during
slave_configure (if it has one).
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch adds a device driver for scsi media changer devices.
Signed-off-by: NGerd Knorr <kraxel@bytesex.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch removes volatile qualifier from scsi_device->device_busy,
Scsi_Host->host_busy and ->host_failed as the volatile qualifiers
don't serve any purpose now.  While at it, convert those fields from
unsigned short to unsigned int as suggested by Christoph.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We have a DID_IMM_RETRY to require a retry at once, but we could do with
a DID_REQUEUE to instruct the mid-layer to treat this command in the
same manner as QUEUE_FULL or BUSY (i.e. halt the submission until
another command returns ... or the queue pressure builds if there are no
outstanding commands).
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

scsi_cmnd->serial_number_at_timeout doesn't serve any purpose
anymore.  All serial_number == serial_number_at_timeout tests
are always true in abort callbacks.  Kill the field.  Also, as
->pid always equals ->serial_number and ->serial_number
doesn't have any special meaning anymore, update comments
above ->serial_number accordingly.  Once we remove all uses of
this field from all lldd's, this field should go.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

scsi_cmnd->internal_timeout field doesn't have any meaning
anymore.  Kill the field.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Adapted from a patch in SuSE's kernel SRPM.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We have a DID_IMM_RETRY to require a retry at once, but we could do with
a DID_REQUEUE to instruct the mid-layer to treat this command in the
same manner as QUEUE_FULL or BUSY (i.e. halt the submission until
another command returns ... or the queue pressure builds if there are no
outstanding commands).
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

scsi_cmnd->serial_number_at_timeout doesn't serve any purpose
anymore.  All serial_number == serial_number_at_timeout tests
are always true in abort callbacks.  Kill the field.  Also, as
->pid always equals ->serial_number and ->serial_number
doesn't have any special meaning anymore, update comments
above ->serial_number accordingly.  Once we remove all uses of
this field from all lldd's, this field should go.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

scsi_cmnd->internal_timeout field doesn't have any meaning
anymore.  Kill the field.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Adapted from a patch in SuSE's kernel SRPM.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- add a comment to the device structure that the device_busy field
  is now protected by the request_queue->queue_lock
- null out sdev->request_queue after the queue is released to trap
  any (and there shouldn't be any) use after the queue is freed.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The current problem seen is that the queue lock is actually in the
SCSI device structure, so when that structure is freed on device
release, we go boom if the queue tries to access the lock again.

The fix here is to move the lock from the scsi_device to the queue.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!